2016 Seat Ibiza ST light

Fuses and bulbs
Fuse arrangement in engine compart-
ment Read the additional information carefully
›››
 p
age 44
Only replace fuses with a fuse of the same
amperage (same colour and markings) and
size.
No.Consumer/Amps
1Fan, condenser40
TK8 fan, condenser50
2Glow plugs50
3ABS Pump40
EMBOX2-13 (TA8)20
4PTC glow phase 250
5PTC glow phase 350
6BDM, 30 ReF5
7MSG (KL30)7.5
8Windscreen wipers30
9Automatic gear box control, AQ 160
Control box30
10ABS Ventil25
EMBOX2-11 (TA8)5
No.Consumer/Amps
12
Injectors
10TDI fuel metering adjuster, TA8 ex-
haust temperature sensor
13Servo sensor5
14coolant pump high/low temperature,
gauge (relay EKP)10
1550 controls motor diag5
16Starter motor30
17Controls motor (MSG KL87)20
18PTC Relays, TOG sensor, engine
valves, PWM fan10
19Interior AUX Fuses30
20Glow plug relay, Heizrohr5
Ignition coil20 Changing bulbs
Gener al
not

es Read the additional information carefully
› ›
›
 p

age 45
Before changing any bulb, first turn off the
failed device. Do not touch the glass part of the bulb with
your bare h

ands. The fingerprints left on the
glass will vaporise as a result of the heat gen-
erated by the bulb, reducing bulb life and
causing condensation on the reflector sur-
face, thus reducing effectiveness.
A bulb must only be replaced by one of the
same type. The type is indicated on the bulb,
either on the glass part or on the base.
Xenon headlights
With this type of headlight, the user can re-
place the turn signal bulb. Replacement of
the dipped/main beam bulb must be done by
Technical Services, given that complex ele-
ments must be removed from the vehicle and
the automatic control system that incorpo-
rates it must be reset.
The Xenon bulbs discharge 2.5 times the
light flux and have an average lifespan of 5
times more than that of halogen bulbs, this
means that, except due to unusual circum-
stances, there is no need to change the bulbs
for the whole life of the vehicle. WARNING
● Take p ar

ticular care when working on com-
ponents in the engine compartment if the en-
gine is warm, there is a risk of burns.
● Bulbs are highly sensitive to pressure. The
glass
can break when you touch the bulb,
causing injury. » 83
Technical data
Advice
Operation
Emergencies
Safety

Emergencies
●
The high vo lt
age element of gas discharge
bulbs* (xenon light) must be handled correct-
ly. Otherwise, there is a risk of death.
● When changing bulbs, please take care not
to injure y
ourself on sharp parts in the head-
light housing. CAUTION
● Remov e the ignition k

ey before working on
the electric system. Otherwise, a short circuit
could occur.
● Switch off the lights or parking lights be-
fore y
ou change a bulb. For the sake of the environment
Please ask your specialist retailer how to dis-
pose of u sed b

ulbs in the proper manner. Note
● Depending on w e

ather conditions (cold or
wet), the front lights, the fog lights, the tail
lights and the turn signals may be temporari-
ly misted. This has no influence on the useful
life of the lighting system. By switching on
the lights, the area through which the beam
of light is projected will quickly be demisted.
However, the edges may continue to be mis-
ted.
● Please check at regular intervals that all
lighting (espec
ially the exterior lighting) on
your vehicle is functioning properly. This is not only in the interest of your own safety,
but a
l

so that of all other road users.
● Before changing a bulb, make sure you
have the corr
ect new bulb.
● Do not touch the glass part of the bulb with
your bare h
ands, use a cloth or paper towel
instead. The residue left by the fingerprints
would vaporise as a result of the heat gener-
ated by the bulb, they will be deposited on
the reflector and will impair its surface. Single headlight bulb change
P o
sition of

the bulbs Fig. 91
Single headlight. Side lights - Dipped beam/main beam.
T
urn s
ignal

light.
DRL (day light)
A B
C Turn signal and DRL (day light) light
Fig. 92
Single headlight DRL light (day light). Fig. 93
Single turn signal lamp. –
Raise the bonnet.
– Turn the bulb holder ››
›
Fig. 92
1 or
› ›
›
Fig. 93
2 to the left and pull.
– Remove the bulb by pressing on the bulb
ho l
der and t urnin

g it anti-clockwise at the
same time.
84

Fuses and bulbs
– Ins
tal
lation involves all of the above steps
in reverse sequence.
Dipped/main beam headlights and
side light Fig. 94
Single headlight. Fig. 95
Dipped beam/main beam and side
light of
the s in

gle headlight. Remove the cover
– Raise the bonnet.
– Move the loop ›
››
Fig. 94
1 in the direction
of the arr
ow and r
emove the cover.
Changing the dipped/main beam headlight – Remove connector ››› Fig. 95
3 from the
b u
lb
.
– Unclip the retainer spring ››› Fig. 95
2 pressing inwards to the right.
– Extract the bulb and fit the replacement so
th at
the lug on the b a

se fits into the recess
on the reflector.
– Fit the connector.
– Fit the cover and close the strap. Make sure
that the ga

sket sits well on the casing cover
during the operation.
– Check whether the new bulb is working.
Changing the s
ide light
– Extract the bulb holder ››› Fig. 95
4 out-
w ar
ds.
– R
emove the bulb by pulling it out and fit-
ting the new one.
– Inst

allation involves all of the above steps
in reverse sequenc
e.
– Fit the cover and close the strap. Make sure
that the ga

sket sits well on the casing cover
during the operation. –
Check whether the new bu
lb is working.
Double headlight bulb change Position of
the bulbs Fig. 96
Double headlight. Side lights
M
ain be
am hea

dlights
Dipped beam headlights
Turn signal
DRL (LED day light)
A B
C
D
E
85
Technical data
Advice
Operation
Emergencies
Safety

Emergencies
Side light and main beam Fig. 97
Double headlight. Fig. 98
Side light and main beam headlights. Remove the cover
– Raise the bonnet.
– Move the loop 1 in the direction of the ar-
r o
w and r emo
ve the cover ››› Fig. 97. Changing the side light
– Remove connector ››› Fig. 98
2 by pulling
outw ar
d.
– Remo
ve the bulb by pulling it out and fit-
ting the new one.
– Inst

allation involves all of the above steps
in reverse sequenc
e.
– Fit the cover and close the strap. Make sure
that the ga

sket sits well on the casing cover
during the operation.
– Check whether the new bulb is working.
Changing the m
ain beam bulb
– Remove connector ››› Fig. 98
3 by pulling
outw ar
d.
– Extr act
the bulb and fit the replacement so
that it s
its correctly into the cut-out on the
reflector.
– Installation involves all of the above steps
in reverse sequenc

e.
– Fit the cover and close the strap. Make sure
that the ga

sket sits well on the casing cover
during the operation.
– Check whether the new bulb is working. Dipped beam headlight
Fig. 99
Double headlight. Fig. 100
Dipped beam headlights. –
Raise the bonnet.
– Move the loop ››
›
Fig. 99
1 in the direction
of the arr
ow and r
emove the cover.
– Remove connector ››› Fig. 100
2 from the
b u
lb
.
86

Fuses and bulbs
– Unc lip the r
etainer s
pring ››› Fig. 100 3 pressing inwards to the right.
– Extract the bulb and fit the replacement so
th at
the lug on the b a

se fits into the recess
on the reflector.
– Fit the connector.
– Fit the cover and close the strap. Make sure
that the ga

sket sits well on the casing cover
during the operation.
– Check whether the new bulb is working.
Turn signal light Fig. 101
Turn signal light. –
Raise the bonnet.
– Turn the bulb holder ››
›
Fig. 101
1 to the
l ef t
and p
ull. –
Remove the b
ulb by pressing on the bulb
holder and turning it anti-clockwise at the
same time.
– Installation involves all of the above steps
in reverse sequenc

e.
Changing the AFS headlight
bulb
s
Position of the bulbs Fig. 102
AFS headlight bulbs. Turn signal
X
enon he
adlight

(dipped beam/main
beam)
A B Changing the xenon bulb
The procedure for changing the bulb is the
same on both side
s

of the vehicle. WARNING
This type of bulb should be changed at a spe-
cia li

sed workshop. Turn signal bulb
Fig. 103
Turn signal light. –
Raise the bonnet.
– Turn bulb holder ››
›
Fig. 103
A to the left
and p u
ll
.
– Remove the bulb by pressing on the bulb
holder and turnin

g it anti-clockwise at the
same time.
– Installation involves all of the above steps
in reverse sequenc

e.
87
Technical data
Advice
Operation
Emergencies
Safety

Emergencies
Changing the fog light bulbs Fr ont
fog light
bulbFig. 104
Front fog light. Fig. 105
Front fog light. –
Remove the bolt ››
›
Fig. 104
1 from the fog
light gri
ll
e with a screwdriver.
– Subsequently, remove the clips located on
the edge of the gril

l with gentle leverage. –
Remove the 3 bo
lts ››› Fig. 105 2 to re-
mo v
e the f og light
.
– Remove the metal clip situated on the up-
per part of

the fog light by pulling towards
the exterior of the vehicle ››› Fig. 105 3 .
FR version fog-light bulb Fig. 106
Fog light: access to the connector
and t o the light
bu

lb holder. –
Remove the 4 bolts A
› ›
› Fig. 106 fr

om the
inside of the wheel housing and the 2 bot-
tom bolts B
› ›
› Fig. 106 fr

om the bumper
with a screwdriver.
– Pull the bumper to release it from its an-
chorage

s to access the connector and the
light bulb holder. Note
Due to the difficulty of accessing fog light
bul b

s, have them replaced at a Technical
Service or specialised workshop. Remove the bulb holder
Fig. 107
Front fog light. –
Remove connector ››
›
Fig. 107
1 from the
b u
lb
.
– Turn the bulb holder ››› Fig. 107
2 to the
l ef
t and p
ull.
– Remove the bulb by pressing on the bulb
holder and turnin

g it counter-clockwise at
the same time.
– Installation involves all of the above steps
in reverse sequenc

e.
– Check that the bulb works properly.
88

Fuses and bulbs
Changing the tail light bulbs S umm
ary
of LED tail lights3 Applies to the model: IBIZA/IBIZA SC
LED
● Brak e lights
● Side lights
B

ulb
s
● Retro fog light
● Reverse lights
● Turn signal
Tail light summary 3 Applies to the model: IBIZA ST
T ai

l lights on side panel Bulb lamps
● Brake lights
● Side lights
● Turn signal
Lights on the r e

ar lid Bulb lamps
● Reverse lights
● Side lights
● Fog lights Tail lights on side panel LED lamps
●
Brake light (LED)
● Side light (LED)
● Turn signal
Lights on the re
ar lid LED lamps
● Reverse lights
● Side light (LED)
● Fog lights
Access to tail lights 3 Applies to the model: IBIZA/IBIZA SC
Fig. 108
Access to tail lights. ●
Open the rear lid.
● Turn the bolt in the direction of the arrow,
b y
h and or w

ith a screwdriver ››› Fig. 108.
● Remove the tail light, by pulling it out-
wards. Ch

anging the tail light bulbs 3 Applies to the model: IBIZA/IBIZA SC
Fig. 109
Changing the tail light bulbs Fig. 110
Changing the tail light bulbs ●
Remove the connector from housing A ›››
Fig. 108. »
89
Technical data
Advice
Operation
Emergencies
Safety

Emergencies
● Remo
ve the b
ulb holder, separating it from
the casing. To do this, press tabs B in the
dir ection of
the arro
ws ››› Fig. 109.
● When the bulb holder has been removed,
press
in the direction of the arrow 1 and at
the s ame time, t
urn in the dir ection of
the ar-
row 2
› ››
Fig. 110
Ch angin

g bulbs. LED lamps
Carry out the same operations as in lights fit-
ted with bulbs.
If necessary, remove the socket, as if it were
a bulb.
If the brake light and/or side light with LEDs
have to be replaced, the tail light must be re-
placed. Changing the tail light bulbs (on the
side panel) 3 Applies to the model: IBIZA ST
Fig. 111
Lights on the side. Fig. 112
Removing the bulb holder. Accessing the side light bulbs
● Open the rear lid.
● Look for a lid with a grill behind the side
lights. ●
Remo
ve the lid w

ith a flat screwdriver, plac-
ing it in notch A
› ››
Fig. 111
.
Ch an
ging bulbs
● Remove the bulb holder by pressing the
fast
ening clip B
› ››
Fig. 112
and pu
lling it
outwards.
● Replace the faulty bulb, rotating it to the
left and outw
ards.
● To refit follow the steps in reverse order,
taking s
pecial care when fitting the bulb
holder.
Changing bulbs. LED lamps
Carry out the same operations as in lights fit-
ted with bulbs.
If necessary, remove the socket, as if it were
a bulb.
If the brake light and/or side light with LEDs
have to be replaced, the tail light must be re-
placed.
90