2016 RENAULT MEGANE HATCHBACK light

trip computer and warning system......................... (current page)
warning lights......................................................... (current page)
instrument panel messages................................... (current page)
instrument panel .................................................... (current page)
1.63
ENG_UD23625_1
Ordinateur de bord : messages d’information (X95 - B95 - D95 - K95 -\
Renault)
ENG_NU_837-8_BDK95_Renault_1
TRIp c O mp UTER AN d WARNIN g s Y s TE m : information messages
Examples of messages Interpreting the display selected
“Battery low start engine” Indicates that the vehicle must be started to recharge the battery (eg. after the engine has been
switched off for some time whilst listening to the radio).
“
p lease remove keycard” Request to remove the RENAULT card from the reader when you leave the vehicle.
“
c hecking control functions” Displayed with the ignition on when the vehicle is running self-diagnost\
ics.
“Traction control off” Indicates that you have deactivated the ASR function.
“Turn steeringwheel +
s TART” Turn the steering wheel slightly whilst pressing the vehicle start button to unlock the steering
column.
“No message available” No warning is stored.
“
s teering wheel
not locked” Indicates that the steering column has not been locked.
“
s top vehicle” Indicates an electronic parking brake fault. Apply the electronic parking brake manually and ensure
that the vehicle is immobilised using a chock.
These can help in the vehicle starting phase, or give information about \
a selection or a driving status.
Examples of information messages are given in the following pages.

trip computer and warning system......................... (current page)
instrument panel messages................................... (current page)
warning lights......................................................... (current page)
instrument panel .................................................... (current page)
1.64
ENG_UD23626_1
Ordinateur de bord : messages d’anomalies de fonctionnement (X95 - B\
95 - D95 - K95 - Renault)
ENG_NU_837-8_BDK95_Renault_1
TRIp c O mp UTER AN d WARNIN g s Y s TE m : operating fault messages
These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as
soon as possible. If you fail to follow this recommendation, you risk da\
maging your vehicle.
They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The
©
warning light stays on. Examples of operating fault messages are given i\
n the following pages.
Examples of messages Interpreting the display selected
“
c
lean diesel filter” Indicates the presence of water in the diesel filter.
“
c
heck lighting” Indicates a fault in the directional headlights.
“
c
heck vehicle” Indicates a fault on one of the pedal sensors or in the battery management
system.
“
c
heck airbag” Indicates a fault in the restraint system in addition to the seat belts. In the event
of an accident, it is possible that they may not be triggered.
“
c
heck antipollution system” Indicates a fault in the vehicle’s particle filter system.
“
c
heck injection” Indicates an engine fault.

trip computer and warning system......................... (current page)
warning lights......................................................... (current page)
instrument panel messages................................... (current page)
instrument panel .................................................... (current page)
1.65
ENG_UD23627_1
Ordinateur de bord : messages d’alerte (X95 - B95 - D95 - K95 - Rena\
ult)
ENG_NU_837-8_BDK95_Renault_1
TRIp c O mp UTER AN d WARNIN g s Y s TE m : warning message
These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic
conditions allow.
s
top your engine and do not restart it. c ontact an approved d ealer.
Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually
or alternately (when there are several messages to be displayed), and \
may be accompanied by a warning light and/or a beep.
Examples of messages Interpreting the display selected
“Engine failure hazard” Indicates engine overheating, or an injection or engine oil pressure fau\
lt.
“
p
ower steering fault” or
“Risk of steering locking” Indicates a fault in the steering.
“
p
arking brake fault” Indicates an electronic parking brake fault. Apply the electronic parking brake manually
and ensure that the vehicle is immobilised using a chock.
“Battery charging fault” Indicates a fault in the vehicle battery charging circuit (alternator e\
tc.).
“
p
uncture” Indicates a puncture on the tyre displayed on the instrument panel.

menu for customising the vehicle settings
(up to the end of the DU)
customising the vehicle settings ........... (up to the end of the DU)
customised vehicle settings .................. (up to the end of the DU)
1.66
ENG_UD11347_2
Menu de personnalisation des réglages du véhicule (X95 - B95 - D9\
5 - Renault)
ENG_NU_837-8_BDK95_Renault_1
vehicle settings customisation menu
vEHIcLE sETTINgs cUsTOmIsATION mENU
Adjusting the settingsPress one of buttons 2 or 3 to select a
function to change:
a)

Auto door locking while driving;
b)


Unlock driver
’s door only;
c)

Auto rear wipe with reverse gear;
d)


Auto dipped-beam headlights;
e)


Front parking sensor;
f)


Rear parking sensor;
g)


Parking sensor volume ;
h)


LANGUAGE
.
= function activated
< function deactivated
On equipped vehicles, this function,
which is integrated in the trip compu-
ter and warning system
1
,

allows you
to activate/deactivate some of the vehi-
cle’s functions.
Accessing the settings
customisation menu
With the vehicle stationary, press
either button 2
or 3
until the mes-
sage “Settings menu: press and hold”
appears on display
1 .

Press either
button
2 or 3 for longer than 2 seconds
to enter the menu.
Once a line has been selected, keep
pressing either button 2 or 3 to change
the function: If you select either “Parking
sensor volume” or “LANGUAGE”, you
will be given a new choice of options
(parking distance control volume or in-
strument panel language). In this case,
make your selection and confirm it by
holding either button
2

or
3,

the value
selected is shown by a
~ in front
of the line.
To exit the menu, select “EXIT” or
“BACK” then confirm by holding either
button
2

or
3 .

It may be necessary to
carry out this operation several times.
2
3
1
The vehicle settings customisation
menu cannot be used when driv-
ing. At speeds of above 12 mph (20
km/h) for vehicles with a manual
gearbox (0 mph for vehicles with an
automatic gearbox), the on-board
display returns automatically to the
trip computer and warning system
mode.

rear view mirrors ................................... (up to the end of the DU)
1.69
ENG_UD21504_2
Rétroviseurs (X95 - B95 - D95 - Renault)
ENG_NU_837-8_BDK95_Renault_1
Door mirrors
folding door mirrors
T he door mirrors automatically fold in
when the vehicle is locked (switch
2 in
position
B )

. In this case, they will fold
out when the ignition is next switched
on.
In any case, you can make the door
mirrors fold in (switch
2 in position C) or
fold out (switch
2 in position
A
).
Automatic mode is then deactivated. To
reactivate it, position switch

2
to B.
REAR vIEW mIRRORs
door mirrors
Adjustment
Select the door mirror using switch 3,
then
use button 1 to adjust it to the de-
sired position.
Heated door mirrors
Mirror de-icing is carried out at the
same time as rear screen de-icing.
The driver ’s door mirror
may have two clearly de-
fined zones. Zone
E shows
what can normally be seen
in an ordinary rear view mirror.
Zone

D increases rear side visibility.
The objects in zone
D look much
further away than they really are.
Interior rear view mirror
Its position can be adjusted.
Rear view mirror with lever
4
When driving at night, to avoid being
dazzled by the headlights of the vehicle
behind, depress the little lever located
behind rear view mirror

4
.
Rear view mirror without lever
4
The rear view mirror darkens automati-
cally at night if you are being followed
by a vehicle with its lights on.
1
2
A
c
B
4
dE
3

warning buzzer ..................................... (up to the end of the DU)
headlight flashers ................................. (up to the end of the DU)
indicators .............................................. (up to the end of the DU)
lights: hazard warning ............................... (up to the end of the DU)
lights: direction indicators .......................... (up to the end of the DU)
indicators: direction indicators .......................... (up to the end of the DU)
hazard warning lights signal ................. (up to the end of the DU)
hazard warning lights signal ................. (up to the end of the DU)
horn ...................................................... (up to the end of the DU)
horn: flash ................................................................. (current page)
horn: sounding the horn ............................................ (current page)
horn ....................................................................... (current page)
audible and visual signals..................... (up to the end of the DU)
1.70
ENG_UD6289_1
Avertisseurs sonore et lumineux (X95 - B95 - D95 - Renault)
ENG_NU_837-8_BDK95_Renault_1
Audible and visual signals
AUdIBLE ANd vIsUAL sIgNALs
Horn
Press on the sides of the steering wheel
boss
A.
Headlight flasher
Pull stalk 1 towards you to flash the
headlights.
éHazard warning lights
Press switch 2. This switch ac-
t
ivates all four direction indicators and
the side indicator lights simultaneously.
It must only be used in an emergency to
warn drivers of other vehicles that you
have had to stop in an area where stop-
ping is prohibited or unexpected or that
you are obliged to drive under special
conditions.
Depending on the vehicle, the hazard
warning lights may come on automati-
cally under heavy deceleration. You can
switch them off by pressing switch
2.
direction indicators
Move stalk 1 parallel to the steering
wheel and in the direction you are going
to turn it.
When driving on the motorway, the
steering wheel is not often turned
enough to return the stalk automatically
to
0 .

There is an intermediate position
in which the stalk may be held when
changing lanes.
When the stalk is released, it automati-
cally returns to
0.
A
2
1
0

lighting:exterior ............................................ (up to the end of the DU)
instrument panel .................................................... (current page)
lights: side lights ......................................................... (current page)
lights: dipped beam headlights ................................... (current page)
hazard warning lights signal .................................. (current page)
signals and lights .................................. (up to the end of the DU)
lighting: instrument panel .............................................. (current page)
daytime running lights............................................ (current page)
1.71
ENG_UD24014_3
Éclairages et signalisations extérieurs (X95 - B95 - Renault)
ENG_NU_837-8_BDK95_Renault_1
daytime running lights
function
Depending on the vehicle, the daytime
running lights come on automatically
when the engine is started. To activate
or deactivate this function, refer to the
information on the “Vehicle settings
customisation menu” in Section 1.
ámain beam headlightsWith the dipped beam head-
lights lit, pull stalk 1
towards you. This
indicator light on the instrument panel
comes on.
To return to the dipped headlight posi-
tion, pull stalk
1 towards you again.
Exterior lighting and signals
Before driving at night,
check that the electrical
equipment is operating cor-
rectly and adjust the head-
light beams (if your vehicle is not
carrying its normal load). As a gen-
eral precaution, check that the lights
are not obscured (by dirt, mud,
snow or objects being transported).
EXTERIOR LIgHTINg AN d s I g NAL s (1/3)
1
31
uside lights
Turn the ring 2 until the symbol
i
s opposite mark 3 .
This indicator light
on the instrument panel comes on.
kdipped beam
headlights
manual operation
T urn the ring 2 until the symbol is oppo-
site mark
3 .

This indicator light on the
instrument panel comes on. Automatic operation
(depending on vehicle)
Turn ring
2 until the AUTO symbol is op-
posite mark 3: with the engine running,
the dipped beam headlights switch on
or off automatically depending on the
brightness of the light outside, without
any action on stalk 1.
2
If driving on the right in a left-hand
drive vehicle (or vice versa), drivers
are recommended to have the lights
adjusted by an authorised dealer for
the duration of the trip.

lights:main beam headlights ...................................... (current page)
warning buzzer ...................................................... (current page)
see-me-home lighting ............................................ (current page)
lights mobile directional ............................................. (current page)
1.72
ENG_UD24014_3
Éclairages et signalisations extérieurs (X95 - B95 - Renault)
ENG_NU_837-8_BDK95_Renault_1
Jaune NoirNoir texte
EXTERIOR LIgHTINg AN d s I g NAL s (2/3)
1
special note:
– I f the dipped beam headlights are
manually switched on and if the light
is sufficient, the directional head-
lights will remain fixed;
–

I
f the lights come on automatically
when cornering, the directional
headlights will start working from the
next time the vehicle corners;
–

W
hen the dipped beam headlights
are switched on with the engine
running and the vehicle stationary,
the lights move to reinitialise them-
selves. If not, there is a system fault.
switching off the lights
There are two possibilities:
– Manually , move ring 2 to position 0;
–

a
utomatically, the lights will go out
when the engine is switched off, the
driver’s door is opened or the vehicle
is locked. In this case, the next time
the engine is started the lights will be
switched back on according to the
position of the ring

2
.
NB: if the fog lights are lit, the lights are
not switched off automatically.
“see-me-home lighting”
function
This function allows you to briefly switch
on the dipped beam headlights (to pro-
vide light when opening a gate, etc.).
With the engine and lights off and
ring

2
in the 0 position, pull stalk

1
to-
wards you: the dipped beam headlights
light up for approximately thirty sec-
onds. To increase this duration, you
may pull the stalk up to four times (total
time restricted to two minutes). The
message “See-me-home _ _ _” along
with the times the lights will be on for
is displayed on the instrument panel to
confirm this action.
To switch off the lights before they go
out automatically, turn ring
2 to any po-
sition, then return it to position 0.
directional headlights
Depending on the vehicle, with the
dipped beam headlights on and under
certain conditions (speed, steering
wheel angle, forwards gear selected,
etc.) when cornering, the dipped beam
headlights move to light the inside of
the bend.
Operating faults
When the message “Check lighting”,
accompanied by the
© warning
light is displayed on the instrument
panel, there is a lighting fault.
Consult an approved dealer.
2