2016 RENAULT MEGANE HATCHBACK light

speed limiter ......................................... (up to the end of the DU)
cruise control-speed limiter................... (up to the end of the DU)
cruise control ........................................ (up to the end of the DU)
driving ................................................... (up to the end of the DU)
2.23
ENG_UD18934_2
Régulateur-limiteur de vitesse : fonction limiteur (X95 - B95 - D95 \
- Renault)
ENG_NU_837-8_BDK95_Renault_2
Speed limiter
CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3)
The speed limiter function helps you
stay within the driving speed limit that
you choose, known as the limit speed.Controls
1 Main “On/Off” switch.
2
L
imit speed activation, storage and
increase switch (+).
3

Decrease limit speed (-).
4


Switch
the function to standby (with
memorisation of the limit speed) (O).
5

A
ctivation and recall of stored limit
speed (R).
Switching on
Press switch 1 on the side showing .
Indicator light 7
comes on, lit orange,
and the message “Speed limiter” ap- pears on the instrument panel, accom-
panied by dashes in zone

6 to indicate
that the speed limiter function is acti-
vated and waiting to store a limit speed.
To store the current speed, press
switch
2

(+): The limited speed will
appear in zone

6. The minimum stored
speed is 20 mph (30 km/h).
2
3
5
4
76
1

2.24
ENG_UD18934_2
Régulateur-limiteur de vitesse : fonction limiteur (X95 - B95 - D95 \
- Renault)
ENG_NU_837-8_BDK95_Renault_2
Jaune NoirNoir texte
Driving
When a limited speed has been stored
and this speed is not reached, driving is
similar to driving a vehicle without the
speed limiter function.
Once you have reached the stored
speed, no effort on the accelera-
tor pedal will allow you to exceed
the programmed speed except in an
emergency (refer to information on
“Exceeding the limit speed”).
Varying the limit speed
The limit speed may be changed by re-
peatedly pressing:
–

switch
2 (+) to increase the speed;
–

switch
3 (-) to decrease the speed.
Exceeding the limit speed
It is possible to exceed the limit speed
at any moment. To do this: press the
accelerator pedal firmly and fully
(beyond the kickdown point).
While the speed is being exceeded, the
limit speed flashes on the instrument
panel and area

C
lights up red.
Then, as far as is possible, release
the accelerator pedal: the speed lim-
iter function will return as soon as you
reach a speed lower than the stored
speed.
Limited speed cannot be maintained
If driving up or down a steep gradient,
the system is unable to maintain the
limit speed: the stored speed on the
instrument panel will flash and zone


C
will light up in red to inform you of this
situation.
The speed limiter function is
in no way linked to the brak-
ing system.
C
2
3
5
4
CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3)

JauneNoirNoir texte
2.25
ENG_UD18934_2
Régulateur-limiteur de vitesse : fonction limiteur (X95 - B95 - D95 \
- Renault)
ENG_NU_837-8_BDK95_Renault_2
Recalling the limit speed
If a speed has been stored, it can be re-
called by pressing switch
5 (R).
CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3)
Putting the function on
standby
The speed limiter function is sus-
pended when you press switch 4
(O).
In this case, the limit speed will remain
stored and is no longer displayed in
zone
6

and the message “Memorised”
along with the stored speed will appear
on the display.
1
When the speed limiter is put on
standby, pressing switch 2
(+) re-
activates the function without taking
into account the stored speed: it is
the speed at which the vehicle is
moving that is taken into account.
Switching off the function
The speed limiter function is deacti-
vated if you press switch 1: in this case
a speed is no longer stored. The in-
strument panel orange indicator light
7
goes out to confirm that the function is
deactivated.
6
2
3
5
4
7

JauneNoirNoir texte
2.27
ENG_UD18935_2
Régulateur-limiteur de vitesse : fonction régulateur (X95 - B95 -\
D95 - Renault)
ENG_NU_837-8_BDK95_Renault_2
CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4)
Switching on
Press switch 1 on the side showing .
Indicator light

7 comes on, lit green, and
the message “Cruise control” appears
on the instrument panel and dashes
appear in zone
6

to indicate that the
cruise control function is activated and
waiting to store a cruising speed.
Activating cruise control
At a steady speed (above 20 m ph
( 3 0 k m / h ) a p p r o x i m a t e l y ) p r e s s
switch
2

(+): the speed is stored. The
cruising speed will appear in zone

6
.
Cruise control activation is confirmed
when area

A
lights up green in addition
to indicator light
7 .

Area
B

also lights
up green to indicate that the cruising
speed has been reached.
Driving
Once a cruising speed is stored and
the cruise control function is active,
you may lift your foot off the accelera-
tor pedal.
Important: you are never-
theless advised to keep
your feet close to the pedals
in order to react if neces-
sary.
7
A
bC6
2
3
5
4
1

2.28
ENG_UD18935_2
Régulateur-limiteur de vitesse : fonction régulateur (X95 - B95 -\
D95 - Renault)
ENG_NU_837-8_BDK95_Renault_2
Jaune NoirNoir texte
Putting the function on
standby
The function is suspended when you:
–

press switch
4 (O);
–

depress the brake pedal;
–


depress
the clutch pedal or shift into
neutral if the vehicle has an auto-
matic gearbox.
In all three cases, the cruising speed re-
mains stored, it is no longer displayed in
zone
6

and the message “Memorised”
along with the stored speed will appear
on the instrument panel.
Standby is confirmed when zones
A, B
and
C go out.
Exceeding the cruising speed
The cruising speed may be exceeded
at any time by depressing the acceler-
ator pedal. The cruising speed flashes
on the instrument panel along with the
illumination of zone
C
in red.
Then, release the accelerator: after a
few seconds, the vehicle will automati-
cally return to its set cruising speed.
Cruising speed cannot be
maintained
If driving up or down a steep gradient,
the system is unable to maintain the
cruising speed: the stored speed on the
instrument panel will flash and zone


C
will light up in red to inform you of this
situation.
CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4)
Adjusting the cruising speed
The cruising speed may be changed by
pressing the following repeatedly:
–
switch
2 (+) to increase the speed;
–

switch
3 (-) to decrease the speed.
The cruise control function
is in no way linked to the
braking system.
A
bC6
2
3
5
4

JauneNoirNoir texte
2.29
ENG_UD18935_2
Régulateur-limiteur de vitesse : fonction régulateur (X95 - B95 -\
D95 - Renault)
ENG_NU_837-8_BDK95_Renault_2
CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4)
Note: if the speed previously stored is
much higher than the current speed,
the vehicle will accelerate more rapidly
to reach this threshold.
When the cruise control function is
put on standby, pressing switch
2 (+)
reactivates the cruise control func-
tion without taking into account the
stored speed: it is the speed at
which the vehicle is moving that is
taken into account.
Switching off the function
The cruise control function is deacti-
vated if you press switch 1: in this case
a speed is no longer stored. The instru-
ment panel green indicator light
7

and
zones
A , B

and
C

go out, confirming
that the function is deactivated.
Putting the cruise control
on standby or switching it
off does not cause a rapid
reduction in speed: you
must brake by depressing the brake
pedal.
1
Returning to the cruising speed
If a speed is stored, it can be recalled,
once you are sure that the road condi-
tions are suitable (traffic, road surface,
weather conditions, etc.).
Press switch
5 (R) if the vehicle speed
is above 20 mph (30 km/h).
When recalling the stored speed
zone
A

lights up to confirm activation.
Zone
B lights up as soon as the cruis-
ing speed is reached.
A
bC
2
3
5
4
7

2.32
ENG_UD14786_3
Aide au parking (X95 - B95 - D95 - Renault)
ENG_NU_837-8_BDK95_Renault_2
PARkING DISTANCE CONTROL (3/3)
Special features
Ensure that the ultrasonic sensors are
not obscured (by dirt, mud, snow, etc.).
Operating faultsWhen the system detects an operating
fault there will be a 5-second continu-
ous beep as a warning. Consult an ap-
proved dealer.
When the vehicle is being driven at
a speed below approximately 6 mph
(10 km/h), certain noises (motorcy-
cle, lorry, pneumatic drill, etc.) may
trigger the beeping sound.
Temporary deactivation of
the system
(depending on the vehicle)
Press switch 1 to deactivate the system.
The message “Parking sensor off” is
displayed to remind you that the system
is deactivated.
Pressing the switch again will reacti-
vate the system and switch off the in-
dicator light.
The system will reactivate automatically
each time the engine is switched off.
Prolonged deactivation of the
system
You may permanently activate or deac-
tivate the front or rear parking distance
control separately.
From the vehicle settings customisa-
tion menu (refer to the information on
the “Vehicle settings customisation
menu” in Section 1), select the line
“Front parking sensor” or “Rear parking
sensor” then activate or deactivate the
system:
<: function deactivated;
= function activated.
Adjusting the parking
distance control volume
From the vehicle settings customisa-
tion menu (refer to the information on
“Vehicle setting customisation menu”
in Section 1), select the line “Parking
sensor volume” to adjust the parking
distance control volume and confirm by
pressing key

2
or 3.
2
3

automatic gearbox (use) ....................... (up to the end of the DU)
automatic gearbox selector lever.......... (up to the end of the DU)
changing gear ....................................... (up to the end of the DU)
reverse gear selecting .......................................... (up to the end of the DU)
driving ................................................... (up to the end of the DU)
2.33
ENG_UD21799_7
Boîte automatique (X95 - B95 - D95 - Renault)
ENG_NU_837-8_BDK95_Renault_2
Selector lever 1
Display 3 on the instrument panel
shows the mode and gear selected.
4:

P:

park
5

:


R:

reverse gear
6

:
N:

neutral
7

:
D:

automatic mode
8

:
manual mo
de
9:



zone
displaying gearbox mode or
gear engaged in manual mode
Operation
With the gear lever 1 in position P,
switch on the ignition.
To move out of position P, you must de-
press the brake pedal before pressing
unlocking button

2
.
With the foot on the brake pedal (warn-
ing light
c on the display 3 goes out),
move the lever out of position P.
Only engage D or R when the vehi-
cle is stopped, with your foot on the
brake and the accelerator pedal re-
leased.
Automatic gearbox
AUTOMATIC TRANSMISSION (1/3)
Driving in automatic mode
Select position D. In most traffic con-
ditions, you will not have to touch the
gear selector lever again: the gears will
change automatically at the right time
and at the most suitable engine speed
because the automatic system takes
into account the vehicle load and road
contour and adjusts itself to the particu-
lar driving style you have chosen.
Economical driving
When driving, always leave the lever
in position D, keeping the accelerator
pedal lightly depressed to ensure auto-
matic gear changes at a lower engine
speed.
Accelerating and overtaking
Depress the accelerator pedal firmly
and fully (so that it goes beyond the
kickdown point).
This will enable you to change down
to the optimum gear within the
engine range.
3
2
1
4
5
6
78
9