2016 NISSAN NOTE height

FRONT SEAT BELTSB-11
< REMOVAL AND INSTALLATION >
C
DE
F
G
I
J
K L
M A
B
SB
N
O P
Before removing the D-ring anch or bolt, note the positions of washers and spacers for correct
installation.
4. Remove center pillar upper finisher. Refer to INT-25, "
CENTER PILLAR UPPER FINISHER : Removal
and Installation".
5. Remove seat belt height adjuster bolts and the seat belt height adjuster. CAUTION:
Before removing the seat belt height adjuster bo lts, note the positions of washers and spacers for
correct installation.
INSTALLATION
Installation is in the reverse order of removal.
• Make sure that the seat belt height adjuster is locked in the lowest position during installation.
• Make sure both the D-ring anchor and seat belt height adjuster operate freely.
• Tighten the D-ring anchor bolt and seat belt height adjuster bolts to specification. Refer to SB-8, "
Exploded
View".
• Always perform an inspection after repair to make sure the system is functioning within specifications. Refer
to SB-5, "
Inspection".
Revision: August 2015 2016 Versa Note

cardiagn.com

DIFFERENTIAL SIDE OIL SEALTM-249
< REMOVAL AND INSTALLATION > [CVT: RE0F11A]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
DIFFERENTIAL SIDE OIL SEAL
Exploded ViewINFOID:0000000012431204
Removal and InstallationINFOID:0000000012431205
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove the front drive shaft from the transaxle assembly. Refer to FAX-19, "Removal and Installation"
2. Remove the differential side oil seal using suitable tool.
CAUTION:
When removing the differential side oil seal, be careful not to scratch the oil seal mating surfaces
of the transaxle case and converter housing.
INSTALLATION
CAUTION:
When inserting the drive shaf t, be sure to use Tool.
1. Measure height (A) of seal lip. Calculate protrusion (C) of seal
lip according to measured height (A) of seal lip and reference
value (B) of side oil seal insertion.
CAUTION:
• Do not reuse differential side oil seal.
• Put a mark on the measurement area and measure height of seal lip at four points diagonally
using suitable tool.
NOTICE:
1. Transaxle assembly 2. Differential side oil seal (left side) 3. Differential side oil seal (right side)
Front Genuine NISSAN CVT Fluid NS-3
JSDIA1888ZZ
Tool number : KV38107900 ( — )
(1) : Differential side oil seal
(2) : Converter housing or transaxle case
Lip protrusion (C): C=A–B
Differential side oil seal insertion
reference value (B) : 1.8 mm (0.071 in)
JSDIA4816ZZ
Revision: August 2015
2016 Versa Note

cardiagn.com

TM-250
< REMOVAL AND INSTALLATION >[CVT: RE0F11A]
DIFFERENTIAL SIDE OIL SEAL
Since seal lips have a tolerance of
± 0.3 mm ( ± 0.012 in) at maximum due to manufacturing tolerances or
packing conditions, it is necessary to measure t he seal lip height beforehand to clarify the tolerance.
2. As an indicator of the parallelism and insertion depth, cut a masking tape (1) to specified width [add 1 mm (0.04 in) to the
value calculated from the tip of differential side oil seal lip] and
affix to the differential side oil seal.
3. Install the differential side oil seal using a suitable tool according to the guide of the masking tape (1).
CAUTION:
• If differential side oil seal is inserted deeper than the ref-erence value, use a new differe ntial side oil seal and per-
form the steps again.
• Apply ATF to the differential side oil seal lip and around
the oil seal.
NOTE:
A hub cap (Part No. 43234 1HA0A) can be used as substitute for drift. To use a hub cap, be sure to pre-
pare a new one specifically for patting seal.
4. Remove masking tape.
5. Adjust as instructed below to optimize the protrusion size and parallelism. CAUTION:
If differential side oil seal is inserted deeper th an the reference value, use a new differential side
oil seal and perform the steps again.
• Protrusion size (A) CAUTION:
Protrusion must fall within ± 0.5mm (0.020 in) of calculated
size.
• Parallelism at four diagonal points ( ) CAUTION:
The difference among four diagona l points must be within 0.3
mm (0.012 in).
NOTE:
If differential side oil seal is uneven while installing, tilt suitable tool.
6. Check that the protrusion size and parallelism are adequate.
Inspection and AdjustmentINFOID:0000000012431206
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to TM-228, "Inspection".
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to TM-229, "Adjustment".
JSDIA4817ZZ
JSDIA4815ZZ
JSDIA4814ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com