!Take care not to spill any coolant on painted
surfaces. You could otherwise damage the
paintwork.
Example: cap and coolant expansion tank
Checkingt he coolant level
XStop your vehicle as far awayf rom traffic as
possible on level ground.
XSwitch off the engine.
XSecure the vehicle to prevent it from rolling
away.
XOpen the hood (Ypage 241).
XSlowly turn cap :half aturn counter-clock-
wise to allow excess pressure to escape.
XTurn cap :further and remove it from cool-
ant expansion tank ;.
XCheck the coolant level.
If the coolant is up to marker bar =in the
filler neck when cold, there is asufficient
amount of coolant in coolant expansion
tank ;.
If the coolant is approximately 0.59 in
(1.5 cm) above marker bar =in the filler neck
when warm, there is asufficient amount of
coolant in coolant expansion tank ;.
Adding coolant
XIf the coolant drops under marker bar =in
the filler neck, add coolant.
Observe the information on the correct cool-
ant mixture ratio and the required water qual-
ity under "Service products and capacities"
(
Ypage 300). To prevent damage to the
engine cooling system, use only approved
corrosion inhibitor/antifreeze that complies
with the Mercedes-Benz Specifications for
Service Products.
XReplace cap :and turn it clockwise to
tighten.
XStart the engine.
XSet the temperature in the vehicle interior to
the maximum output on the air-conditioning
system control panel.
XAfter approximately 5minutes ,switch off the
engine and allow it to cool down.
XCheck the coolant level againa nd add coolant
if necessary.
XClose the hood.
Brake fluid
GWARNING
Service products may be poisonous and haz-
ardous to health. There is arisk of injury.
Comply with instructionsont he use, storage
and disposalofs ervice products on the labels
of the respective original containers. Always
store service products sealed in their original
containers. Alwaysk eep service products out
of the reach of children.
GWARNING
Opening the hood when the engine is over-
heated or when there is afire in the engine
compartment could expose you to hot gases
or other service products. There is arisk of
injury.
Let an overheated engine cool down before
opening the hood. If there is afire in the
engine compartment,k eep the hood closed
and contact the fire department.
GWARNING
Certain componentsint he engine compart-
ment, such as the engine, radiator and parts
of the exhaust system, can become very hot.
Working in the engine compartment poses a
risk of injury.
Where possible,l et the engine cool down and
touch only the componentsd escribed in the
following.
Brake fluid is hazardous to health. Also observe the safety notes under "Service products and
capacities" (
Ypage 295).
Engine compartment245
Maintenance and care
Z
.
The coolant is amixture of water and antifreeze
and corrosion inhibitor. It performs the following
tasks:
Rcorrosion protection
Rantifreeze protection
Rraises the boiling point
When the vehicl eisfirst delivered, it is filled with
ac oolant mixture that ensure sadequate anti-
freeze and corrosion protection. Coolant must
remai ninthe engine cooling system all year
round to ensure anti-corrosion protection and a
higher boiling point, even in countries with high
outside temperatures.
To prevent damage to the engine cooling sys-
tem, use only approved antifreeze and corrosion
inhibitor that complies with the Mercedes-Benz Specifications for Service Products.
Mercedes-Benz recommends an antifreeze and
corrosion inhibitor that meets the requirements
in the Mercedes-Benz Specifications for Service
Products Sheet Number 325.
Check the antifreeze/corrosio ninhibitor con-
centration in the coolant every six months.
The percentag eofcorrosion inhibitor/anti-
freeze additive in the engine cooling system
should:
Rbe at least 50%. This way, the engine cooling
system is protected against freezing downt o
approximately -35 ‡(-37 †).
Rnot exceed 55% (antifreeze protection down
to -49 ‡[-45 †]) .Otherwise, hea twilln ot be
dissipated as effectively.
If ther ehasbeen coolant loss, do not refill only
with water. If the vehicl ehaslost coolant, add
equa lparts water and antifreeze/corrosion
inhibitor. The water used as part of the coolant
mixture must fulfil lcertain requirements; these
are usuall yfulfille dbyd rinking water. If the
water quality is not sufficient, yo umusttrea tthe
water.
Mor einformatio ncan be obtaine datany qual i-
fi eds p
ecialist workshop.
Servic eproduct: coolant
Productn ame/number
Zerex G40-91, The Valvoline Company
MB SheetNo. 325.5
Maintenance interval
Hav ethe coolant renewe devery 15 years .
Capacities
Engine coolin gsystem
CoolantApprox. 11 US qt
(10.4l)
Clim ate control systemr efrigerants
Important safety notes
The climate control system of you rvehicle is fil-
led with the refrigerant R ‑134a.
The warning label for the refrigerant being used
can be found on the radiator cross member.
!Only the refrigerant R ‑134a and the PAG oil
approved by Mercedes-Benz may be used.
The approved PAG oil may not be mixed with
any other PAG oil that is not approved for
R-134a refrigerant. Otherwise ,the climate
control system may be damaged.
Maintenance work such as adding refrigerant or
replacing components may only be carried out
by aq ualified specialist workshop. All applicable
regulations thereto and the SAE standard J639
need to be respected.
All work on the climate control system should
always be carried out at qualified specialist
workshop.
Service products and capacities301
Technical data
Z
