2016 HONDA PILOT Quick Guide

138 || 139
HANDLING THE UNEXPECTED
HANDLING THE UNEXPECTED
Fuse Locations
If any electrical devices are not working, turn the vehicle off and chec\
k to see if any
applicable fuse is blown. Fuse locations are shown on the fuse box cover\
. Locate the
fuse in question by the fuse number and box cover number.
Engine Compartment Fuse Box Type A
Located under the hood on the passenger’s side. Push the tabs to open the box.
Circuit ProtectedAmps
1
(70 A)RR BLOWER30 AABS/VSA MTR40 AABS/VSA FSR20 AMAIN FAN30 AMAIN FUSE150 A
2
SUB FAN30 AWIP MT R30 AWASHER20 ASUNSHADE(20 A)(30 A)FR BLOWER40 AAC INVERTER(30 A)AUDIO AMP(30 A)RR DEF40 A(30 A)(20 A)
3

4 PARKING LIGHT 10 A
5
6 STOP LIGHT 10 A
7
8L H/L LO 10 A
9
10 R H/L LO 10 A
11 IGPS 7.5 A
13 H/L LO MAIN 20 A
15 FR FOG (15 A)
16 HAZARD 15 A
17 AS P/SEAT (REC) (20 A)
18 AS P/SEAT (SLIDE) (20 A)
19 ACM 20 A
20 MG CLUTCH 7.5 A
21 MAIN RLY 15 A
22 FI SUB1 5 A
23 IG COIL 15 A
24 DBW1 5 A
25 SMALL/STOP MAIN (20 A)
26 BACK UP 10 A
27 HTD STRG WHEEL (10 A)
28 HORN 10 A
29 RADIO (20 A)
Circuit Protecte
d Amps
14 USB CHARGER (15 A)
12
INJECTOR (20 A)
Circuit Protected Amps
1
(70 A)
RR BLOWER 30 A
ABS/VSA MTR 40 A
ABS/VSA FSR 20 A
MAIN FAN 30 A
MAIN FUSE 150 A
2 SUB FAN
30 A
WIP MT R 30 A
WASHER 20 A
SUNSHADE (20 A)
(30 A)
FR BLOWER 40 A
AC INVERTER (30 A)
AUDIO AMP (30 A)
RR DEF 40 A
(30 A)
(20 A)
3




4 PARKING LIGHT 10 A5
6 STOP LIGHT 10 A
7
8L H/L LO 10 A
9
10 R H/L LO 10 A
11IGPS7.5 A
13H/L LO MAIN20 A
15FR FO G(15 A)
16 HAZARD 15 A
17AS P/SEAT (REC)(20 A)
18 AS P/SEAT (SLIDE) (20 A)
19ACM20 A
20 MG CLUTCH 7.5 A
21MAIN RL Y15 A
22 FI SUB15 A23IG COIL15 A
24 DBW15 A25SMALL/STOP MAIN(20 A)
26 BACK UP 10 A
27HTD STRG WHEEL(10 A)
28 HORN 10 A
29RADIO(20 A)
Circuit Protecte dAmps
14USB CHARGER (15 A)
12
INJECTOR (20 A)
Ta b
Engine Compartment Fuse Box Type B
Located under the hood near the brake fluid reservoir. Push the tabs to open the
box.
Circuit ProtectedAmps
1
ST CUT1(40 A)4W D(20 A)IG MAIN30 AIG MAIN230 APTG MTR(40 A)F/B MAIN260 AF/B MAIN60 AEPS60 A2TRL MAI N(30 A)3TRL E-BRAKE(20 A)
4 BMS 7.5 A
5H/L HI MAI N20 A
6 PTG CLOSER (20 A)
7CTR ACC SOCKET20 A
8 RR ACC SOCKET (20 A)
9FR DE-ICE(15 A)
10 ACC/IG2_MAIN 10 A
11TRL CHARGE(20 A)12IDLE STOP ST CUT(30 A)13IDLE STOP(30 A)14IDLE STOP(30 A)15TCU/SBW(15 A)16RR HEATED SEAT(20 A)17STRLD7.5 A
Ta b

140 || 141
HANDLING THE UNEXPECTED
HANDLING THE UNEXPECTED
Interior Fuse Box Type A
Located under the dashboard.
Fuse label
Fuse box
Circuit ProtectedAmps1DR P/W20 A2DOOR LOCK20 A3SMART7.5 A4AS P/W20 A5FR ACC SOCKET20 A6FUEL PUMP20 A7ACG15 A8FRONT WIPER7.5 A
9ABS/VSA7.5 A10SRS10 A11REAR LEFT P/W20 A1213REAR RIGHT P/W20 A14FUEL LID20 A15DR P/SEAT (REC )(20 A)16REAR FOG(7.5 A)17FR SEAT HEATER(20 A)18INTR LT7.5 A
19 DR REAR DOOR UNLOCK 10 A
20 AS SIDE DOOR UNLOCK 10 A
21 DRL 7.5 A
22 KEY LOCK 7.5 A
23 A/C 7.5 A
24 IG1a FEED BACK 7.5 A
25 INST PANEL LIGHTS 7.5 A
*1: Models with auto idle stop
*2: Models without auto idle stop
26
LUMBAR SUPPORT (10 A)
27 PARKING LIGHTS 7.5 A
28 OPTION 10 A
29 BACK LT
7.5 A
METER 7.5 A
30 REAR WIPER 10 A
31 ST MOTOR
(7.5 A)
MISS SOL (7.5 A)
32 SRS 7.5 A
33 AS SIDE DOOR LOCK 10 A
34 DR DOOR LOCK 10 A
35 DR DOOR UNLOCK 10 A
36 DR P/SEAT (SLIDE )(20 A)
37 RIGHT H/L HI 10 A
38 LEFT H/L HI 10 A
39 IG1b FEED BACK 7.5 A
40 ACC 7.5 A
41 DR REAR DOOR LOCK 10 A
42
Circuit Protecte
d Amps
*1
*1
*2
*2
*2 IG1 SMART 7.5 A*1
Circuit Protected Amps
1 DR P/W 20 A
2 DOOR LOCK 20 A
3 SMART 7.5 A
4 AS P/W 20 A
5 FR ACC SOCKET 20 A
6 FUEL PUMP 20 A
7 ACG 15 A
8 FRONT WIPER 7.5 A
9 ABS/VSA 7.5 A
10 SRS 10 A
11 REAR LEFT P/W 20 A
12
13 REAR RIGHT P/W 20 A
14 FUEL LID 20 A
15 DR P/SEAT (REC )(20 A)
16 REAR FOG (7.5 A)
17 FR SEAT HEATER (20 A)
18 INTR LT 7.5 A19DR REAR DOOR UNLOCK10 A20AS SIDE DOOR UNLOCK10 A21DR L7.5 A22KEY LOCK7.5 A23A/C7.5 A24IG1a FEED BACK7.5 A25INST PANEL LIGHTS7.5 A
*1: Models with auto idle stop
*2: Models without auto idle stop
26LUMBAR SUPPORT(10 A)27PARKING LIGHTS7.5 A28OPTION10 A
29BACK LT7.5 AMETER7.5 A30REAR WIPER10 A
31ST MOTOR(7.5 A)MISS SOL(7.5 A)32SRS7.5 A33AS SIDE DOOR LOCK10 A34DR DOOR LOCK10 A35DR DOOR UNLOCK10 A36DR P/SEAT (SLIDE )(20 A)37RIGHT H/L HI10 A38LEFT H/L HI10 A39IG1b FEED BACK7.5 A40ACC7.5 A41DR REAR DOOR LOCK10 A42
Circuit Protecte dAmps
*1
*1
*2
*2
*2 IG1 SMART 7.5 A*1
Interior Fuse Box Type B*
Located under the dashboard.
Circuit ProtectedAmpsAMETER7.5 ABABS/VSA7.5 ACACG7.5 ADMICU7.5 AEAUDIO20 AFBACK UP10 AGACC7.5 AFuse label
Fuse box
*if equipped
Inspecting and Changing Fuses
1. Turn the vehicle off, including all lights and
accessories.
2. Remove the fuse box cover.
3. Check the large fuse in the engine compartment.
If the fuse is blown, use a Phillips-head
screwdriver to remove the screws and replace
the fuse with a new one. Reinstall the screws.
4. Inspect the small fuses in the engine
compartment and the vehicle interior.
If there is a burned out fuse, remove it with the
fuse puller and replace it with a new one.
Replacing a fuse with one that has a higher rating greatly increases the\
chances of
damaging the electrical system.
NOTICE
Blown fuse
Fuse puller
Combined
fuse

142 || 143
MAINTENANCE
MAINTENANCE
Safety Precautions
Some of the most important safety precautions are listed below; however, we cannot
warn you of every conceivable hazard that can arise in performing mainte\
nance.
Only you can decide whether or not you should perform a given task.
Maintenance Safety
•  To reduce the possibility of fire or explosion, keep cigarettes, sparks\
, and flames
away from the battery and all fuel-related parts.
•  Never leave rags, towels, or other flammable objects under the hood.
•  To clean parts, use a commercially available degreaser or parts cleaner, not
gasoline.
•  Wear eye protection and protective clothing when working with the battery\
or
compressed air.
•  Do not run the engine in confined spaces where carbon monoxide gas can\

accumulate.
Vehicle Safety
•  The vehicle must be stationary, and parked on level ground with the parking
brake set and the engine off.
•  Be aware that hot parts can burn you.
•  Be aware that moving parts can injure you.
•  Do not open the hood while the Auto Idle Stop function* is activated.
Improperly maintaining this vehicle or failing to correct a problem befo\
re
driving can cause a crash in which you can be seriously hurt or killed. \
Always follow the inspection and maintenance recommendations according
to the schedules in this guide.
WARNING
Failure to properly follow maintenance instructions and precautions can \
cause you to be seriously hurt or killed.
Always follow the procedures and precautions in this guide.
WARNING
Learn about basic maintenance that you can perform on the vehicle yourse\
lf, as well
as information about how to best maintain the vehicle.
MAINTENANCE
*if equipped
Maintenance Minder™
When maintenance is due, the system message indicator comes on and a mes\
sage
appears on the display every time you turn the vehicle on. See page 144 to check
what maintenance is due indicated by the codes that appear.
Press the Info (p/q) button on the steering wheel to change displays.
System message indicator
Main
items Sub items
Maintenance Minder message
• Independent of the Maintenance Minder information, replace the brake fl\
uid
every 3 years.
•  Inspect idle speed every 160,000 miles (256,000 km).
•  Adjust the valves during services A, B, 1, 2, or 3 if they are noisy.
U.S. models
Maintenance, replacement, or repair of emissions control devices and sys\
tems
may be done by any automotive repair establishment or individuals using \
parts
that are certified to EPA standards.
According to state and federal regulations, failure to perform maintenan\
ce on the
maintenance main items marked with # will not void your emissions warranties.
However, all maintenance services should be performed in accordance with the
intervals indicated by the multi-information display.

144 || 145
MAINTENANCE
MAINTENANCE
Maintenance Minder Service Codes
These codes indicate what services are due on your vehicle.
*1: If the message Maintenance Due Now does not appear more than 12 months after the display
is reset, change the engine oil every year.
#: See information on maintenance and emissions warranty.
*2: If you drive in dusty conditions, replace the air cleaner element every \
15,000 miles (24,000 km).
*3:
If you drive primarily in urban areas that have high concentrations of s\
oot in the air from industryand diesel-powered vehicles, replace every 15,000 miles (24,000 km).
CODEMaintenance Main Items
A
Replace engine oi l*1
BReplace engine oil*1 and oil lter
Inspect front and rear brakes
Check parking brake adjustment
Inspect tie rod ends, steering gearbox, and boots
Inspect suspension components
Inspect driveshaft boots
Inspect brake hoses and lines (Including ABS/VSA)
Inspect all uid levels and condition of uids
Inspect exhaust system#
Inspect fuel lines and connection s#
*4:If you drive regularly in very high temperatures (over 110°F, 43°\
C), in very low temperatures
(under -20°F, -29°C), or towing a trailer, replace every 60,000 \
miles/100,000 km.
*5:Driving in mountainous areas at very low vehicle speeds or trailer towin\
g results in higher level
of mechanical (Shear) stress to uid. This requires differential \
uid changes more frequently
than recommended by the Maintenance Minder. If you regularly drive your \
vehicle under these
conditions, have the differential uid changed at 7,500 miles (12,00\
0 km), then every 15,000 miles
(24,000 km).
CODEMaintenance Sub Items
1
Rotate tires
2Replace air cleaner element*2
Replace dust and pollen lter*3
Inspect drive belt
3
Replace transmission uid, transfer uid
4Replace spark plug s
Replace timing belt and inspect water pump*4
Inspect valve clearance
5
Replace engine coolant
6Replace rear differential ui d*, *5
*
*if equipped
Under the Hood
Opening the Hood
1. Park the vehicle on a level surface, and set the
parking brake.
2. Pull the hood release handle under the lower left
corner of the dashboard.
3. Push up the hood latch lever in the center of the
hood to release the lock mechanism, and open
the hood.
4. Remove the support rod from the clamp using the
grip. Mount the support rod in the hood.
When closing, remove the support rod, and
stow it in the clamp, then gently lower the hood.
Remove your hand at a height of approximately
12 inches (30 cm) and let the hood close.
Brake fluid (black cap)
Battery
Engine oil fill cap
Lever
Support rod Grip
Clamp
Pull
Washer fluid
Engine coolant
reservoir tank Engine oil dipstick
(orange)
Radiator cap
Do not open the hood when the wiper arms are raised. The hood will strik\
e the
wipers, and may damage either the hood or the wipers.
Do not open the hood while the Auto Idle Stop* function is activated.
NOTICE
*if equipped

146 || 147
MAINTENANCE
MAINTENANCE
Engine Compartment Cover
The component parts in the engine compartment are protected by a cover. You
may need to remove the cover when you perform certain maintenance work.
Starting at either side, lift the outermost edge of
the engine compartment cover. Pull up on the
cover, and remove it from the pins. Move towards
the opposite side while applying uniform upward
pressure.
Recommended Engine Oil
•  Honda Genuine Motor Oil
•  Premium-grade 0W-20 detergent oil with an API Certification Seal on the
container
This seal indicates the oil is energy conserving and
that it meets the American Petroleum Institute’s
latest requirements.
Use Honda Genuine Motor Oil or another
commercial engine oil of suitable viscosity for the
ambient temperature as shown.
You may also use synthetic motor oil if it is labeled with the API Certifi\
cation Seal
and is of the specified viscosity grade.
Engine Oil
Park the vehicle on level ground, and wait approximately three minutes after turning
the engine off before you check the oil.
Checking the Oil
1. Remove the dipstick (orange).
2. Wipe the dipstick with a clean cloth or paper
towel.
3. Insert the dipstick back all the way into its hole.
4. Remove the dipstick again, and check the level.
It should be between the upper and lower marks.
Add oil if necessary.
Upper markLower mark
Ambient temperature

148 || 149
MAINTENANCE
MAINTENANCE
Adding Oil
1. Unscrew and remove the engine oil fill cap.
2. Add oil slowly.
3. Reinstall the engine oil fill cap, and tighten it
securely.
4. Wait for three minutes and recheck the engine oil
dipstick.
Do not fill the engine oil above the upper mark. Overfilling the eng\
ine oil can result
in leaks and engine damage.
NOTICE
Engine oil fill cap
Resetting the Engine Oil Life
If you change or replace the vehicle’s engine oil yourself, you must reset the
engine oil life. Use the steering wheel buttons to operate the menu.
1. Use the Info (p/q) buttons to scroll to the Vehicle
Settings menu. Press the RESET button to enter the
menu.
2. Scroll to Maintenance Info, and select it.
3. Press and hold the RESET button to enter the oil life
reset mode.
4. Select Reset. The maintenance codes disappear,
and the engine oil life returns to 100%.
Failure to reset the engine oil life after a maintenance service results\
in the
system showing incorrect maintenance intervals, which can lead to seriou\
s
mechanical problems.
NOTICE
Engine Coolant
Park the vehicle on level ground. Check the reserve tank and the coolant\
level in the
radiator. We recommend Honda Long Life Antifreeze/Coolant Type 2.
Checking the Reserve Tank
1. Check the amount of coolant in the reserve tank.
2. If the coolant level is below the MIN mark, add
the specified coolant until it reaches the MAX
mark.
3. Inspect the cooling system for leaks.
Adding Coolant
1. Make sure the engine and radiator are cool.
2. Remove the engine compartment cover.
3. Turn the radiator cap counterclockwise and
relieve any pressure in the coolant system. Do
not push the cap down when turning.
4. Push down and turn the radiator cap
counterclockwise to remove it.
5. The coolant level should be up to the base of the
filler neck. Add coolant if it is low.
6. Put the radiator cap back on, and tighten it fully.
7. Pour coolant into the reserve tank until it reaches
the MAX mark. Put the cap back on the reserve
tank.
Removing the radiator cap while the engine is hot can cause the coolant \
to spray
out, seriously scalding you.
Always let the engine and radiator cool down before removing the radiato\
r cap.
WARNING
If temperatures consistently below −22°F (−30°C) are expec\
ted, the coolant
mixture should be changed to a higher concentration. Consult a dealer fo\
r details
for more information.
NOTICE
Pour the fluid slowly and carefully so you do not spill any. Clean up any spills
immediately; they can damage components in the engine compartment.
NOTICE
Radiator
cap MAX
MIN

150 || 151
MAINTENANCE
MAINTENANCE
Checking the Battery
The battery condition is monitored by the sensor on the negative termina\
l. If there
is a problem with the sensor, a message appears on the multi-information display.
Have your vehicle checked by a dealer.
For jump starting, see page 129.
The battery gives off explosive hydrogen gas during normal operation.
A spark or flame can cause the battery to explode with enough force to\
kill or
seriously hurt you.
When conducting any battery maintenance, wear protective clothing and a \
face
shield, or have a skilled technician do it.
WARNING
WARNING: Battery posts, terminals, and related accessories contain lead and lead\

compounds. Wash your hands after handling.
Window Washer Fluid
If the washer fluid level is low, fill the washer reservoir. You can check the level by
looking at the reservoir, or a message* will appear on the MID.
Pour the washer fluid carefully. Do not overflow the reservoir.
Do not use engine antifreeze or a vinegar/water solution in the windshie\
ld washer
reservoir. Antifreeze can damage your vehicle’s paint. A vinegar/water solution can
damage the windshield washer pump.
NOTICE
Brake Fluid
The fluid level should be between the MIN and MAX marks on the side of\
the
reservoir. We recommend using Honda Heavy Duty Brake Fluid DOT 3.
Pour the fluid carefully.
If the fluid level is at or below the MIN mark, have a
dealer inspect for leaks or worn brake pads as soon as
possible.
Brake fluid marked DOT 5 is not compatible with your vehicle’s braking system and
can cause extensive damage.
NOTICE
*if equipped
Brake reservoir MAX
MIN
Changing Wiper Blades
If the wiper blades leave streaks across the windshield, try cleaning th\
em first with a
paper towel or soft cloth and wiper fluid. If the wiper blade rubber h\
as deteriorated,
you should change the wiper blades.
Changing the Front Wiper Blade Rubber
1. Lift the driver side wiper arm first, then the
passenger side.
2. Place a cloth on the edge of the lock tab. Push
the lock tab up with a flat-tip screwdriver.
3. Slide the blade from the wiper arm.
4. Slide the wiper blade out from its holder by
pulling the tabbed end out.
5. Remove the retainers from the rubber blade that
has been removed, and mount to a new rubber
blade. Correctly align the rubber protrusion and
the retainer grooves.
6. Slide the new wiper blade onto the holder from
the bottom end. The tab on the holder should fit
in the indent of the wiper blade. Slide the wiper
blade onto the wiper arm until it locks
7. Slide the wiper blade onto the wiper arm, then
push down the lock tab.
8. Lower the passenger side wiper arm first, then
the driver side.
Lock tab
Blade
Retainer
Avoid dropping the wiper arm, as it may damage the windshield.
NOTICE
Blade

152 || 153
MAINTENANCE
MAINTENANCE
Changing the Rear Wiper Blade Rubber
1. Raise the wiper arm off.
2. Slide the wiper blade out from the end with the
indent.
3. Remove the retainers from the wiper blade, and
mount to a new rubber blade.
4. Slide the new wiper blade onto the holder. Make
sure it is engaged correctly, then install the wiper
blade assembly onto the wiper arm.
Blade
Retainer
Rubber
Tire Information
To safely operate your vehicle, your tires must be of the proper type and\
size, in good
condition with adequate tread, and properly inflated.
Inflation Guidelines•  Properly inflated tires provide the best combination of handling, trea\
d life, and
comfort. Refer to the driver’s doorjamb label or the specifications (see page
160) for the specified pressure.
•  Underinflated tires wear unevenly, adversely affect handling and fuel economy,
and are more likely to fail from overheating.
•  Overinflated tires make your vehicle ride harshly, are more prone to road
hazards, and wear unevenly.
•  Every day before you drive, look at each of the tires. If one looks lowe\
r than the
others, check the pressure with a tire gauge.
•  Measure the air pressure when tires are cold. This means the vehicle has been
parked for at least 3 hours, or driven less than 1 mile (1.6 km). If n\
ecessary, add
or release air until the specified pressure is reached. If checked whe\
n hot,
tire pressure can be as much as 4-6 psi (30-40 kPa, 0.3-0.5 kgf/cm
2) higher than
checked when cold.
•  At least once a month or before long trips, use a gauge to measure the p\
ressure
in all tires, including the spare. Even tires in good condition can lose\
1-2 psi
(10-20 kPa, 0.1-0.2 kgf/cm
2) per month.
Inspection Guidelines
Every time you inflate the tires, check for the following:
•  Any damage to tires, including bumps, bulges, cuts, splits, or cracks in\
the side
or tread. Remove any foreign objects and inspect for air leaks. Replace \
tires if
you see fabric or cord.
•  Uneven or excessive tread wear. Have a dealer check the wheel alignment.
•  Cracks or other damage around the valve stems.
Wear Indicators
The groove where the wear indicator is located is
1/16 inch (1.6 mm) shallower than elsewhere on the
tire. If the tread has worn so low that the indicator is
exposed, replace the tire. Worn out tires have poor
traction on wet roads.
Example of a wear
indicator mark