2016 FIAT FULLBACK Owners Manual

Headlamps (halogen bulb)
1. When replacing the bulb on the right
side of the vehicle, remove the clamps
(A) of the air cleaner filter and move the
upper cover (B) towards the rear of the
vehicle.
Arrow direction: front of the vehicle
NOTE When moving the upper cover
towards the rear of the vehicle, remove
the harness from the air cleaner hooks
(C).Arrow direction: front of the vehicle
NOTE After replacing the bulb, make
sure that the hinges at the front of the
vehicle are firmly set.
2. Disconnect the connector (A).
3. Remove the sealing cover (B).4. Unhook the spring (C) which secures
the bulb, and then remove the
headlamp bulb.
5. To install the bulb, perform the
removal steps in reverse.
B
A
355AHA103954
C
356AHZ100961
A
357AHA102771
B
358AHA102784
B
359AHA102784
215

Position lamps
1. When replacing the bulb on the left
side of the vehicle, remove the clip (A)
holding down the washer tank spout
and move the spout towards the rear of
the vehicle.
2. When replacing the bulb on the right
side of the vehicle in case of
petrol-powered vehicles,
diesel-powered vehicles (4D56), remove
the bolt (B) holding down the power
steering fluid reservoir tank and move
the tank towards the rear of the vehicle.3. Turn the bulb socket anticlockwise to
remove it. And remove the bulb from
the socket by pulling out.
4. To install the bulb, perform the
removal steps in reverse.Front turn-signal lamps
Except for vehicles with high
intensity discharge headlamps
1. When replacing the bulb on the left
side of the vehicle, remove the clip (A)
holding down the washer tank spout
and move the spout towards the rear of
the vehicle.
2. When replacing the bulb on the right
side of the vehicle in case of
petrol-powered vehicles,
diesel-powered vehicles (4D56), remove
the bolt (B) holding down the power
steering fluid reservoir tank and move
the tank towards the rear of the vehicle.
A
360AHA103967
11
361AHA103970
362AHA102801
A
363AHA103967
216
IN CASE OF EMERGENCY

3. Turn the bulb socket anticlockwise to
remove it. And remove the bulb from
the socket by turning it anticlockwise
while pressing in.
3. To install the bulb, perform the
removal steps in reverse.Vehicles with high intensity
discharge headlamps
1. When replacing the bulb on the left
side of the vehicle, remove the clip (A)
holding down the washer tank spout
and move the spout towards the rear of
the vehicle.
2. When replacing the bulb on the right
side of the vehicle in case of
petrol-powered vehicles,
diesel-powered vehicles (4D56), remove
the bolt (B) holding down the power
steering fluid reservoir tank and move
the tank towards the rear of the vehicle.3. Turn the bulb socket anticlockwise to
remove it. And remove the bulb from
the socket by turning it anticlockwise
while pressing in.
3. To install the bulb, perform the
removal steps in reverse.
11
364AHA103970
365AHA102814
A
366AHA103967
11
367AHA103970
368AHA102827
217

Front fog lamps*/Daytime running
lamps*
1. Insert a straight blade (or minus)
screwdriver with a cloth over its tip at
the edge of the cover (A) and pry gently
to remove the cover.
2. Remove the 3 screws (B) and
remove the lamp unit.NOTE When unfastening the screws of
the fog lamp, be careful not to
mistakenly move the beam position
adjustment screw (C).
3. Turn the socket anticlockwise to
remove it.
D. Front fog lamp
E. Daytime running lamp4. While holding down the tab, pull out
the bulb.
5. To install the bulb, perform the
removal steps in reverse.
Rear combination lamps
1. Open the rear gate. (Refer to “Rear
gate”).
2. Remove the screws (A) that hold the
lamp unit.
3. Move the lamp unit toward the rear
of the vehicle and remove the clips (B).
A
369AHA102667
B
370AHA102670
C
371AHZ101056
DD
E
E
372AA0112846
A
373AHA102872
218
IN CASE OF EMERGENCY

4. Remove each socket and bulb
assembly by turning it anticlockwise.
C. Tail and stop lamp Remove the bulb
from the socket by turning it
anticlockwise while pressing in.
D. Rear turn-signal lamp Remove the
bulb by pulling it out.
E. Rear fog lamp (driver’s
side)*/Reversing lamp Remove the bulbby pulling it out.
5. To install the bulb, perform the
removal steps in reverse.
When mounting the lamp unit, align the
pins (F) and clip (G) on the lamp unit
with the holes (H) in the body.Licence plate lamps
Type 1
1. Insert a straight blade (or minus)
screwdriver into the lamp assembly and
pry gently to remove it.
NOTE Wrap a piece of cloth around the
tip of the screwdriver in order to avoid
scratching the lens and the body.
2. Remove the socket and bulb
assembly together by turning it
anticlockwise, and then remove the
bulb by pulling out.
B
374AHA102885
E
D
C
375AHA102898
HF
G
376AHA102902377AHA102915
219

3. To install the bulb, perform the
removal steps in reverse.
NOTE When mounting the lamp unit,
put the hook (A) on the right side of the
lamp unit into the body first.Type 2
1. Remove the screws (A) from the
lamp unit, and then remove the lens
and cover.
2. Remove the bulb by pulling out.
3. To install the bulb, perform the
removal steps in reverse.Front room & map lamps*
1. Insert a straight blade (or minus)
screwdriver into the notch of the lens
and pry gently to remove it. Remove the
bulb from the lamp holder.
NOTE Wrap a piece of cloth around the
tip of the screwdriver in order to avoid
scratching the lens.
2. To install the bulb, perform the
removal steps in reverse.
NOTE When installing the lens, align
the 2 tabs on the lens with the holes on
the vehicle side.
378AHA102928
A
379AHZ100639
380AHA104629
381AHA104632
382AHA102931
220
IN CASE OF EMERGENCY

Rear room lamp
Type 1
1. Insert a straight blade (or minus)
screwdriver into the notch of the lens
and pry gently to remove it. Remove the
bulb from the lamp holder.
NOTE Wrap a piece of cloth around the
tip of the screwdriver in order to avoid
scratching the lens.2. To install the bulb, perform the
removal steps in reverse.
NOTE When installing the lens, align
the 2 tabs on the lens with the holes on
the vehicle side.
Type 2
1. Insert a straight blade (or minus)
screwdriver into the notch of the lens
and pry gently to remove it. Remove the
bulb from the lamp holder.Wrap a piece of cloth around the tip of
the screwdriver in order to avoid
scratching the lens.
2. To install the bulb, perform the
removal steps in reverse.
NOTE When installing the lens, fit the
two tabs on one side of the lens into
the holes on the vehicle side before
fitting the two tabs on the opposite side
of the lens into the holes on the vehicle
side.
383AHA102944
384AHA102957
385AHA102960
386AHA104645
221

Glove box lamp
Have the glove box lamp bulb replaced
at a Fiat dealership.
WARNING
299)Bulbs are extremely hot immediately
after being turned off. When replacing a
bulb, wait for it to cool sufficiently before
touching it. You could otherwise be burnt.
300)Handle halogen lamp bulb with care.
The gas inside halogen lamp bulb is highly
pressurized, so dropping, knocking, or
scratching a halogen lamp bulb can cause
it to shatter.
301)Never hold the halogen lamp bulb
with a bare hand, dirty glove, etc. The oil
from your hand could cause the bulb to
break the next time the headlamps are
operated. If the glass surface is dirty, it
must be cleaned with alcohol, paint thinner,
etc., and refit it after drying it thoroughly.302)Always consult a specialist when
repairing or replacing the bulbs of high
intensity discharge headlamps. This is
because the power circuit, bulbs and
electrodes generate a high voltage that
could cause an electric shock.
303)Modifications or repairs to the electric
system that are not carried out properly or
do not take the system technical
specifications into account can cause
malfunctions leading to the risk of fire.
304)Only replace bulbs when the engine is
off. Also ensure that the engine is cold, to
prevent the risk of burns.
387AHZ101043
222
IN CASE OF EMERGENCY