2016 Citroen JUMPER time

88
jumper_en_Chap04_Technologie-a-bord_ed01-2015
Menu...Press... Sub-menu… Press... Select…c onfirm
and exit Enables you to...
1 Speed beep
on i

ncreaseActivate/deactivate the audible
signal indicating exceeding of
the programmed speed and
select the speed.
Decrease
o

FF
2


Headlamp
sensor
i
ncreaseSet the sensitivity of the
sunshine sensor (1 to 3).
Decrease
3


Activation
Trip B Activate
Display a second distance
"Trip
B".
Deactivate
4

Setting the

time Hours/

Minutes
i

ncreaseSet the clock.
Decrease
Time format 24
Select the clock display mode.
12
5

Setting the

date Year/Month/
Day Activate
Set the date.
Deactivate
6 Autoclose While

moving
onActivate/Deactivate automatic


door locking above approx
12
mph (20 km/h).
o
FF
Vehicle configuration

89
jumper_en_Chap04_Technologie-a-bord_ed01-2015
Menu…Press... Sub-menu… Press... Select…c onfirm
and exit Enables you to...
7

Measurement
unit (Unit)
Distance Km
Select the distance display unit.
Miles
Fuel
consumption km/l
Select the fuel consumption
display unit.
l/100 km
Temperature °C
Select the temperature display
unit.
°F
8 Languages List of
languages
availableSelect the display language.
9

Volume of
announcements
(Buzz)increase Increase/decrease the volume
of the announcements or of the
audible warning.
Decrease
10

Daytime
running lampsonActivate/deactivate daytime
running lamps.
o

FF
11 Service Service

(Miles/km
before service) Display the miles/kilometres
remaining before the next
service.
Oil (Miles/Km
before oil change) Display the miles/kilometres to
the next oil change.
12


Passenger
airbag
(BAG P)
onYe
s Activate the passenger airbag.
n

o
o

FF Ye s
Deactivate the passenger
airbag.
n

o
13

Exit from


menu Exit from the menu. Press the
arrow at the bottom to go to the
first menu.
Vehicle configuration
4
TECHnoLoGY on BoArD

91
jumper_en_Chap04_Technologie-a-bord_ed01-2015
From the "Safety / Help" sub menu, you can:
-
select "Parkview Camera", then

"
r eversing camera" to activate or
deactivate its use (
o n, o ff),
-
select "Parkview Camera", then "Camera


delay" to activate or deactivate the
maintaining of the display for 10 seconds
or up to 11 mph (18 km/h) (On, Off),
-

select "Passenger airbag" to activate or

deactivate its use (
o n, o ff).
From the "Lighting" sub-menu, you can:
-

select "Day lamps" to activate or

deactivate their use (
o n, o ff),
-

select "Headlamp sensor" to adjust its

sensitivity (1, 2, 3).
From the "Doors & locking", you can:
-

select "Autoclose" to activate or

deactivate its use (
o n, o ff).
From the "Display" sub-menu, you can:
-

select "Languages" and choose one of


the languages listed above,
-

select "Units of measurement" to


choose the units for fuel consumption
(l/100

km, mpg), distance (miles, km)
and temperature (°C, °F),
-

select "Display

Trip B" to switch trip B
o

n or
o
ff in the trip computer.
From the "Time and Date" sub-menu, you
can:
-

select "Adjust time and format" to set the


hour, minutes and seconds and choose
the format (24 h, 12 h with am or pm),
-

select "Adjust Date" to set the day

,
month and year.
To set the time manually, "Synch Time"
must be
o
ff.
Vehicle configuration
4
TECHnoLoGY on BoArD

92
jumper_en_Chap04_Technologie-a-bord_ed01-2015
The trIP button, located at the end of the
wiper control stalk, gives access to the
following information:
-
r
ange
This indicates the distance that can still


be travelled with the fuel remaining in
the tank on the basis of the average
consumption over the last few miles
(kilometres) travelled. -
A verage speed A

This is the average speed calculated


since the last trip computer zero reset
(with the ignition on).
-
t
rip

duration A
This indicates the total time since the


last trip recorder zero reset.
-

d istance A

This indicates the distance travelled


since the last trip computer zero reset.
-

A
verage fuel consumption A
This is the average quantity of fuel


consumed since the last trip computer
zero reset.
-
c
urrent fuel consumption A
This is the average quantity of fuel


consumed during the last few seconds.
trIP c OMP ut E r
if TriP B is activated in the MOdE menu:
-
Distance B
-


A
verage fuel consumption B
-

A
verage speed B
-

T
rip duration B
Vehicle data

94
jumper_en_Chap04_Technologie-a-bord_ed01-2015
AudIBLE rEAr PArKInG SEnSOrS
if fitted on your vehicle, the system consists
of four proximity sensors, installed in the
rear bumper.
They detect any obstacle: person, vehicle,
tree, fence, behind the vehicle during the
manoeuvre.
However, objects the size or thickness of
which are detected at the beginning of the
manoeuvre will no longer be detected at the
end of the manoeuvre: blind spots between
and below the sensors. Examples: stake,
roadworks cone or pavement post.
The rear parking sensor system may be
coupled with a reversing camera.Operation
Engage reverse gear with the gear lever.
The proximity information is indicated by an
audible signal of increasing frequency as the
vehicle approaches the obstacle.
When the distance between the rear of
the vehicle and the obstacle is less than
approximately thirty centimetres, the audible
signal becomes continuous.
Switching off
Come our of reverse gear into neutral.
Operating fault
if this warning lamp comes
on in the instrument panel
accompanied by a message in
the screen, contact a C
i T roën

dealer or a qualified workshop.
Good practice
The system cannot, in any circumstances,
replace the need for vigilance on the part of
the driver.
Take even greater care if you reverse with a
rear door open.
i

n bad weather or in winter, ensure that the
sensors are not covered with mud, ice or
snow.
Parking sensors

97
jumper_en_Chap04_Technologie-a-bord_ed01-2015
deactivation
Make a long press on both controls
simultaneously to deactivate the system.
The LEDs remain on.
r
eturn to the nominal floor height
Press the same number of times in reverse
as the level of the position displayed.
r

eactivation
A second long press on both controls
simultaneously reactivates the system. The
LEDs go off.
Automatic correction of loading
floor height
Above 12 mph (20 km/h), the system
automatically returns the rear height to its
nominal value.
Operating fault
if a fault occurs with the system,
this warning lamp comes on.
Good practice
Driving with the suspension set too high or
too low risks damaging components under
the body.
The height may be adjusted automatically to
take account of changes of temperature or
loading.
You must avoid using this control in the
following circumstances:
-

when working underneath the vehicle,
-


when changing a wheel,
-


when the vehicle is being transported by

lorry, train, ferry, boat, ...
To avoid damaging the vehicle or injuring
anyone, check that there is nothing or no
person that might be close to or come into
contact with the vehicle, before raising or
lowering the suspension.
Above 3 mph (5 km/h), the system
reactivates automatically.
Have the system checked by a
C
i T roën dealer or a qualified workshop.
Loading assistance
4
TECHnoLoGY on BoArD

101
jumper_en_Chap05_Securite_ed01-2015
trAjEctOrY c O ntr OL SYS t EMS
Switching off
This system cannot be deactivated by
the
driver.
dynamic stability control
( d S c )
The electronic stability programme acts on
the brake of one or more wheels and on the
engine to keep the vehicle on the trajectory
required by the driver, within the limits of the
laws of physics.
With the DSC system, maintain course
without trying to countersteer.
Operation
The DSC system is activated automatically
each time the vehicle is started. Operating fault
i

llumination of this warning lamp,
accompanied by an audible signal
and confirmed by a message
in the instrument panel screen,
indicates a fault with the DSC system.
Have it checked by a C
i T roën dealer or a
qualified workshop. Operation
This system is activated automatically every
time the vehicle is started.
i

n the event of a problem of adhesion or
trajectory, this system comes into play.
Switching off
i

n exceptional conditions (starting a vehicle
which is bogged down, stuck in snow,
on soft ground...), it may be advisable to
deactivate the AS
r system, so that the
wheels can spin freely and regain grip.
-

Press this button, located in the

middle of the dashboard, to deactivate
the
system.
Anti-slip regulation (ASr)
Anti-slip regulation (also known as traction
control) optimises traction, avoiding wheel
spin by acting on the brakes of the driving
wheels and the engine.
i

f the button's warning lamp comes
on, accompanied by a message in the
instrument panel screen, this indicates that
the AS
r system is deactivated.
i

t comes into operation in the
event of a grip or trajectory
problem.
This is indicated by flashing of this warning
lamp in the instrument panel.
5
Driving safely
SAFETY

102
jumper_en_Chap05_Securite_ed01-2015
reactivation
The AS r system is reactivated automatically
every time the ignition is switched back on.
-

Press this button again to reactivate it

manually.
Operating fault
i

f this warning lamp comes on,
accompanied by an audible signal
and a message in the instrument
panel screen, this indicates a fault
with the AS
r system.
Have it checked by a C
i T roën dealer or a
qualified workshop. Good practice
The DSC and AS
r systems offer exceptional
safety in normal driving, but this should not
encourage the driver to take extra risks or
drive at high speed.
The correct operation of these systems
depend on observation of the manufacturer's
recommendations regarding the wheels
(tyres and rims), the braking components,
the electronic components and assembly
and repair procedures.
After an impact, have these systems
checked by a C
i T roën dealer or a qualified
workshop.Load inertia control
The true total weight of a commercial vehicle
can vary considerably depending on the load
carried. As a result, the centre of gravity of
the vehicle can move, both longitudinally
and in height.
All such variations have an effect on braking,
traction, the behaviour of the vehicle when
cornering and the tendency to overturn.
Load inertia control estimates the true
total weight of the vehicle by analysing its
behaviour under acceleration and braking.
This system then adapts the operation of
the DSC and AS
r systems according to the
weight distribution in the vehicle.
i n critical
situations, your vehicle than remains more
securely on its intended trajectory.
Driving safely