2016 AUDI S8 engine oil

Normal temperature
The engine has reached its operating tempera­
ture once the LEDs up to the center of the gauge
turn on under norma l driving conditions . The
LEDs higher up may turn on when the engine is
under heavy load or the exterior temperature is
high. This is no need to worry as long as the.
warn ing light in the instrument cluster does not
illuminate . If the LEDs in the upper area of the
d isplay and the ind icator light . in the instru­
ment cluster display tu rn on , the coolant temper­
ature is too high
¢page 15.
_& WARNING
-Always observe the warning in ¢ page 220,
Working in the engine compartment,
before
opening the hood and checking the engine
coolant level.
- Never open the engine hood if you see or
hear steam, or if you see engine coolant
dr ipping from the engine compartment. You
could burn yourself. Let the engine cool off
first so that you cannot hear or see any
steam or engine coolant.
(D Note
-Mounting additional lights or accessories in
front of the air inlets reduces the cooling ef­
fect of the radiator. At h igh outside temper­
atures or high engine load, the engine could
overheat .
- The front spoiler has been designed to prop­
erly distribute the cooling air when the veh i­
cle is moving.
If the spo iler is damaged, this
could reduce the cooling effect and the en­
gine could then overheat. Ask your author­
iz ed Audi dealer for assistance.
Tachometer (engine rev counter)
The tachometer indicates the engine RPM (revo­
lutions per minutes).
If engine RPM drops below 1,500, you should
downshift to the next lower gear. The red area at
the end of the scale indicates maximum permis­
sib le eng ine RPM after the break-in period. Be­
fore reaching this area, move the selector lever
Instruments and indicator lights
to position "D (Drive)" or ease your foot off the
acce lerator pedal.
(D Note
The tachome ter needle should only briefly be
in the red zone: you could damage your en­
gine! The beginning of the red zone varies de­
pending on the engine .
@ For the sake of the environment
Upshifting early saves fuel and reduces en­
gine noise.
Fuel gauge
The fue l gauge only works when the ignition is
on. If the fuel level drops below 4 gallons (15 lit­
ers), the bottom LED turns red and the indicator
l ight tllturns on
¢page 21. The bottom LED
blinks red when the fue l level is very low .
The possible range based on the current fue l lev­
el is shown in tab@¢
page 23, fig. 4.
(D Note
Never run the tank completely dry. An irregu­
l ar supply of fuel can cause engine misfiring
and fuel could enter the exhaust system. The
catalytic converter could then overheat and
be damaged.
Indicator Lights
Description
The indicator lights in the instrument cluster
blink or turn on. They indicate functions or mal­
funct ions¢ ,&..
Messages may appear with some indicator lights.
A warning signal will sound at the same time.
The ind icator lights and messages in the center
of the displays may be replaced by other displays.
To show them again, select the tab for indicator lights and messages using the multifunction
steering wheel¢
page 23. If there are several
malfunctions, you can display them one at a time
u sin g the thumbwheel.
IJi,-
11

Instruments and indicator lights
If the indicator light t urns on and the message
app ears, th ere is a malfunction in the gene rator
or veh icle electrical system .
Drive to yo ur autho rized Aud i dea le r o r q ual ified
workshop immediately . Because the vehicle bat ­
tery is discharging, turn off a ll unnecessary e lec­
tr ica l equipment s uch as the radio. Seek profes ­
sional ass istance if the battery charge level is too
low.
(•) Low b attery charge: b attery w ill be charged
while dri ving
If th e ind icator lig ht tu rns on and the message
appears, there may be lim ited starting ab ility .
I f th is message turns off afte r a litt le while, the
b a ttery charged enough wh ile d riving.
If the message does not turn off, have your a u­
thor ized Audi dealer or qualified wo rkshop cor­
re ct the malfunction .
~ Engine
• Engin e stopp ed: No power steering and
brake support .
There is a malfunction in the eng ine or in the fue l
supp ly system .
A large amount of steering and braking force is required when driving a rolling vehicle with the
e ng ine stopped . Try to stop a rolling vehicle ca re­
fu lly on the side of the road. See your autho riz ed
Aud i deale r or qualified repair facility.
A WARNING
-
If the eng ine stops while dr iving, a la rge
amount of braking force is req uired . This in­
creases the risk of an accident. As long as the
vehicle rolls with the ignition switched on and there is enough battery charge, the powe r
steering will still work . If not, a la rge amount
o f stee ring force is requ ired .
16
~ Safety belts
This warning/indicator light reminds you to put
on your safety belt.
The . warn ing/ indicator light illumin ates when
the igni tion is swi tched on to remind th e driver
and any front passenger to put on the safety belt .
Additionally, a n acoust ic wa rning (go ng) w ill also
sou nd.
For more Information
c::> page 138, ~ Safe ty belt
warning light .
"1::::1': Engine oil pressure malfunction
The red engine oil pressure warning symbol re­
quires immediate service or repair . Driving with a
low-oil-pressure indication is likely to inflict se­
vere damage to the engine.
• Switch o ff engine and check oil le vel
If the indicator light turns on and the message
appears, the oil pressure is too low .
.. Pull off the road .
.. Stop the vehicle.
.. Turn off the engine .
.. Che ck the engine oil le vel c::> page 224.
.. If the eng ine o il level is too low, add engine oil
c::> page 22 5 . Make sure tha t t he o il pressure
warning symbol. appears no longer in the
display before you sta rt d riving again .
.. If the eng ine o il level is co rrect and the indica­
to r li ght still turns on, tu rn t he e ngine off and
do not cont inue d riv ing. Seek professiona l as­
sistance.
(D Tips
- The engine oil pres sure symbol. is not
an indicator for a low engine oil level. Do
not rel y on it . In stead , check the oil level in
your engine at regular inte rvals , preferably
each time you refuel , and always before
go ing on a long trip .
- The yellow oil level warning indication
II
require s oil refill o r workshop servi ce with­
out delay. Do not wait until the red o il
pre ssure wa rning. starts to flash before
you respond to the low oil le vel warning .,.

a. By then, your engine may already have
suffered serious damage.
~ .. Engine oil level
• WARNING : Please add oil immediately
If the indicator lig ht and the drive r message ap ­
pear, add engine oil immediately
¢ page 223 .
II Add oil , max . x qt (l) . You may continue
driving
W hen t he symbol and the dr ive r message appear,
add the amount of o il appea ring in the display at
the next op portun ity
¢ page 223.
@ -Steering column lock
• Do not drive vehicle : Steering defective
If the indicator light turns on and t he message
a ppear s, there is an ele ctron ic steer ing column
l o ck ma lf u nct io n. You c annot sw itch t he ignit ion
on.
D o
not tow your vehicle beca use it ca nnot be
s teered . See k profess io na l assistan ce.
!II Steering lock: system fault . Please contact
dealer
I f the indicator lig ht t urns on and the message
appears, there is an electron ic steer ing column
l ock malfunct ion.
Drive to yo ur autho rize d Aud i dea le r immediately
to have the malfunct ion corrected.
A WARNING
Your vehicle must not be towed in the eve nt
o f a malfunction i n the elect ronic steering
co lu m n lock because it canno t be s teered d ue
t o the lock ed steering. If it is towed wi th the
steer ing loc ked, the re is the r is k of a n ac ci­
de nt.
© -Engine start system
• Engine start system fault . Plea se contact
dealer
Instruments and ind icator lights
If the indicator ligh t turns on and the message
appea rs, do
not sw itch the ignition off beca use
yo u may not be able to switch it on again.
Dr ive to your au thor ized A udi dea ler imme diately
to have the mal func tion cor rected .
11:J Engine start system fault . Please contact
dealer
If the indicato r ligh t turns on and the message
appea rs , the re is a ma lf u nction in t he e ngine
sta rt sys te m .
D rive to your author ized A udi dealer immediate ly
to have the mal func tion cor rec ted .
0 Air suspension
• Air suspension : system fault. Can continue
slowly with max. 35 mph .
There is a ma lf u nct ion that can res ult in restrict ­
ed dr iving stab ility .
Carefu lly drive at a ma ximum speed of 35 mph
(60 km/h) to your a uthori zed Audi dea ler or
qualifi ed works hop to have t he malfunct io n cor ­
r ec ted .
• Air suspension: service mode. Vehicle can
only be moved with restrictions
Caref ully drive to yo ur aut horize d Aud i dea le r or
qualified wo rks hop immediately to have the serv ­
ice mode deact ivated.
II Air suspension fault
T he re is a syste m malfu nction t hat can resul t in
re strict ed dr iv ing st abilit y or re duced g ro und
cl ear ance.
D rive to your author ized A udi deal er imm ediate ly
t o have the m alfunc tion cor rec ted .
II Air suspension: vehicle too low. Ground
clearance reduced
The gro und clearance is ve ry low due to a system
malfunction . Wait u nti l th e a ir s uspension sys­
tem has resto red normal ground clea rance . Oth ­
erwise , cond itions s uch as an uneven road surface
ca n le ad to ve hicle damage.
17

.... N
0 J:
'SI: .... .... authorized Audi dealer immediately to have the
malfunction corrected.
~ .... Engine oil sensor
• Oil level! Sensor defective
If the symbol illuminates, contact your author­
ized Audi dealer and have the oil sensor inspect­
ed . Until you have this done, check the oil level
each time you refuel just to be on the safe s ide
¢page 224.
f Request to warm engine by driving
0 Please warm up engine
Fuel has entered the engine oil because of low
outside temperatures or frequent short drives. Drive until the engine is warm so that the fuel in
the engine oil will vaporize. Avoid high engine
speeds, full acceleration and heavy engine load
when doing this.
.Bil Fuel level indicator
ID] Please refuel
If the indicator light turns on for the first time
and the message appears, there are about 4 gal­
l ons (15 liters) of fuel left in the tank. Time to re­
fuel
¢ page 214 .
ID] Tank system malfunction! Contact dealer
If the indicator light turns on and this message
appears, there is a malfunction in the tank sys­
tem .
Drive to your authorized Audi dea ler immediately
to have the malfunction corrected.
~ Windsh ield washer fluid level
~ Please refill washer fluid
If the symbol illuminates, add windshield washer
f luid to the washer system/headlight washer sys­
tem*
¢ page 234 .
<$• Windshield wipers
m Windshield wiper defective
Instruments and indicator lights
T he re is a malfunct ion with the windshield wip­
ers .
Drive to your authorized Audi dealer immed iate ly
to have the malfunction corrected .
i§il}0/0$ Defective light bulb warning
1:1-If the indicator light turns on, a bu lb has
failed. The message indicates the location of the
bulb.
fm-if a fog lamp* has failed, the indicator light
turns on to indicate the location on the vehicle.
II-if a rea r fog lamp has failed, the indicator
light turns on to indicate the location on the vehi­
cle.
Vehicle lights: malfunction
If the message appears, there is a malfunction in
the headlights or light switch .
Drive to your authorized Audi dealer immediate ly
to have the malfunction corrected .
A WARNING
-Light bulbs are pressurized and could ex­
plode wh ile they are be ing changed causing
serious personal injury.
- Work w ith due care when handling the high­
voltage section of gas d ischarge (xenon)
lights . Failure to do so could result in death
. . . or serious inJury.
(D Tips
Have the bulb replaced or the connection re­
paired by your author ized Audi Service depart­
ment.
~{D Headlight range control
II Headlight range control: defective!
If the symbol illuminates, the headlight range
control is no longer working properly . Have the
system checked and repaired at your Audi dealer.
21

rl
-Inspection or oil change due: If your vehicle is
due for an inspection or o il change or both, a
message appears br iefly in the instrument clus­
ter display when sw itching the ignition on or
off :
Inspection due! or Oil change due! or Oil
change and inspection duel.
Checking service intervals
The remaining distance or time to the next oil
change or to the next inspection can be viewed in
the MMI. Select the
ICARI function button > Car
systems
control button > Servicing & checks >
Service intervals .
In new vehicles or after resetting the display , the
display can be viewed after approximately
310 miles (500 km) .
Resetting the service interval display
Your authorized Audi dealer will reset the corre­
sponding service schedule after performing the
appropriate service on your veh icle . You also have
the possibility to reset the oil change schedule
after having performed an oil change according
to Audi specificat ions. Select the
ICARI funct ion
button
> Car systems control button > Servicing
& checks > Service intervals > Reset oil change
interval.
@) Note
- Only reset the oil change display when you
have completed an oil change.
- If you disconnect the battery terminals, no
calculations can be made for the service in­
terval display during this time and no serv­
ice remi nder w ill appear. Remember that
observing the proper service interva ls is v i­
tally important to extending the life of your
vehicle, particularly the engine, and main­
taining its value. Even if the mi leage driven
is low, the max imum period of one year
from one service to the next must not be ex­
ceeded .
(!') Tips
-The information in the Serv ice Reminder re­
mains stored even when the vehicle battery
~ i s disconnected .
Instruments and indicator lights
Head-up Display
Applies to: vehicles with Head-up Display
Fig. 14 Exampl e: ind ic a to rs in the Head-up Display
Fig. 15 Instrume nt panel: knob fo r th e He ad- up D isplay
The Head-up Display projects certain warnings or
selected information from the assistance sys­
tems* or navigation* on the windshield . The dis­
play appears wit hi n the driver's field of vision.
Switching on/off
.,. Press the knob~ to switch the Head-up Dis-
play on/off
c:> fig. 15 .
Adjusting the height
The height of the display can be adjusted to the
individual driver.
.,. Make sure you are sea ted correctly
i::>page 130 .
.,. Turn the knob~ to adjust the display .
Settings in the MMI
.,. Select: !CAR ! function button > (Car)* systems
control button > Driver Assist > Head-up Dis­
play
> Head-up Display content or Display
brightness.
27

Smart Techn olo gy
- Under certain climatic and operating condi­
tions such as passing through water, driving
in heavy rain or after washing the vehicle,
the effectiveness of the brakes can be re­
duced . In w inter, ice can accumulate on the
brake pads, linings, discs and drums . Care­
fully apply brakes fo r a tes t. Brakes w ill dry
and ice coatings wi ll be cleaned off after a
few careful brake applications .
- Driving for an extended pe riod of time on
salt-covered roads witho ut using your
brakes can also affect bra king efficiency.
Clean off accumulated salt coating from
brake discs and pads with a few carefu l
brake applications.
- If you damage the front spoiler, or if you in­
stall a different spoiler, be sure the air flow
to the front brakes is not obstructed. Other­
wise the brake system could overheat reduc­
ing the effectiveness of the entire brake sys­
tem.
- Failure of one brake circuit will impair the
braking capability result ing in an increased
stopp ing distance. Avoid driving the vehicle
and have it towed to the nea rest Aud i dealer
or qualified workshop.
- Never let the vehicle roll to a stop with the
engine shut off.
- If the brake booster is not working, the
brake pedal must be pressed considerably
harder to make up for the lac k of booster
assistance.
Electromechanical power
assist, dynamic steering
The electromechanical power assist helps the
driver when steering.
Power steering adapts electronically based on
the vehicle speed.
Ind icator light s and messages
• Stee ring defective! St op th e ve hicle
If th is ind icator light turns on and stays on and
this message appears, the power steer ing may
have fa iled.
194
Do not continue driving. See your authorized
Audi dealer or other qualified repair facility for
ass istance .
,Ion Steering : System faul t You can c ontinue
dri ving
If the indicato r light turns on and the message
appears, the steeri ng may be more diff icult to
move o r more sensitive than usu a l. T he steer ing
whee l may also be at an angle when driving
straight.
D rive slowly to your a uth orized Aud i dea ler or
qualified wo rkshop to have the malfunct ion cor­
rected.
1;r,ij D ynamic steering : Init ializing
If this driver message appears and the indicator
light is flashing on the instrument panel, dynam­
i c steer ing* is being re initialized . After starting
the engine, t he steering wheel w ill move slightly.
Re- initializa tion might be necessary if the steer­
i ng whee l was moved hard to the left and right
while the vehicle was not moving . The display
goes out as soon as initialization is comp lete .
D rive slowly to your a uth orized Aud i dea ler or
qualified wo rkshop to have the mal func tion cor­
rected.
.&_ WARNING
Have the dynamic steering * system malfunc­
tion repaired as soon as possible by an au­
thorized Audi dealer or qualif ied workshop -
risk of acc ident!
(D Tips
If the . or ,Ion indicator light only stays on
for a short time, you may continue driving.
- The dynamic steering* stabi lity systems are
not ava ilable in the event of a system mal­
function.
- For additiona l information on dynamic
steering *, refer to~
page 106 .

Driving and the
environment
Breaking in
New eng ine
The engine needs to be run-in during the first
1,000 miles (1 ,500 km).
For the first 600 miles (1 ,000 kilometers):
"' Do not use full throttle .
"' Do not drive at engine speeds that are more
than 2/3 of the max imum permitted RPM .
"' Avoid high eng ine speeds.
From 600 to 1 ,000 miles (1,000 to 1,500
kilometers ):
"' Speeds can gradually be increased to the maxi­
mum pe rm issib le road or e ngine speed.
During and after b reak-in period
"' Do not rev the engine up to high speeds when it
is cold . This applies whether the transmission is
in N (Neutral) or in gear .
After the bre ak-in period
"' Do not exceed maximum engine speed under
any circumstances .
"' Upshift into the nex t higher gear
before reach­
ing the red area at the end of the tachometer
sca le
c:::;, page 10.
During the first few hours of driving , the eng ine's
internal friction is higher than later when all the
mov ing parts have been broke n in. How well this
b reak-in process is done depends to a considera­
b le exte nt o n the way the veh icle is d rive n du ring
the first 1,0 00 miles (1,500 kilome ters).
(D Note
E xtremely high eng ine speeds a re au toma ti­
cally reduced. However, t hese rpm li mits are
p rogr amme d fo r an eng ine well run-in, not a
new engine .
Driving and the envir onment
{® For the sake of the environment
Do not drive with unnecessarily high engine
spe eds -upshifting early saves fuel, red uces
no ise and protects the environment.
New tires
If your vehicle is runni ng on new tires, drive par­
t icularly careful for the first 3S0 m iles (500 kilo ­
meters) after fitting .
_&. WARNING
New tires tend to be slippe ry and mus t also
b e "bro ken- in". Be sure to remembe r th is dur­
i ng the first 350 m iles ( 500 k ilome ters).
Brake gent ly . Avoid following closely behin d
other vehicles or other s ituations that might
require sudden, hard braking.
Avoid damaging the
vehicle
When you are dr iv ing on poor roads, or over
curbs, steep ramps, etc., make certai n that low ­
ly ing parts such as spo ile rs and exhaust system
parts do not bottom o ut and get damaged .
This is espec ially true for veh icles with low-s lung
chass is (sports c hass is)* and fully loaded
vehicles .
Catalytic converter
Applies to: vehicles with gasoline engine
It is very important that your emission control
system (catalytic converter) is functioning prop ­
erly to ensure that y our vehicle is running in an
environmen tally sound manner.
"' Always use lead-free gasoline c:::;, page 212,
F uel supply .
"' Never run t he tank down all the way to emp ty.
"' Never put too much motor o il in yo ur engine
c:::;, page 225, Adding engine oil ce:r..
"' Never try to push- or tow-start your vehicle.
T he ca talytic co nverter is an efficient "cle an-up"
device built into the exhaust sys tem o f th e vehi -
-
cle. The catalytic converter b urns many of the .,.
197

Driving and th e en vironm ent
pollutants in the exha ust gas before they are re ­
leased into the atmosphere.
The exclusive use of unleaded fue l is critica lly im­
portant for the l ife of the catalytic converter and
proper functioning of the engine.
A WARNING
T he temperature of the exha ust system is
high, both when driving and after stopping
the engine.
-
- Never touch the exhaust tail pipes once they
have become hot. This could result in burns.
- Do not park or operate the vehicle in areas
where the hot exha ust system may come in
contact with dry grass, brush, fue l spill or
other mater ial which can cause a fire.
- Do not apply additional undercoating or rustproofing on or near the exhaust mani­
fold, exhaust p ipes, catalytic converter or
heat sh ields. During dr iv ing, the substance
used fo r undercoating could overheat and
ca use a fire.
(D Note
- Be aware that just one tank filling with
le aded fuel will already ser iously degrade
the performance of the catalytic co nverter .
- Do not exceed the correct eng ine oil level
<=;> page 225.
-Do not drive until the fuel tank becomes
complete ly empty. The engine could mis­
fire. Unburned fuel could also get into the
exhaust system and this cou ld cause the
cataly tic converte r to overheat.
- Do not sw itch off the ignition while the veh i­
cle is moving.
- Do not continue to operate your vehicle un­
der these cond it ions, as otherwise fue l can
r each the catalyti c converte r. This cou ld re­
su lt in overheating of the conve rter, req uir­
i ng its replacement.
- T o assure efficient oper ation of the Emis­
s ion Control Sys tem:
- Have your veh icle maintained properly and
in accordance with the service recommen­
dations in your Warranty
& Maintenance
book let .
198
-Lack of proper ma intenance as well as im ­
proper use of the vehicle wi ll impair the
funct ion o f the emission control system
and could lead to damage.
@ For the sake of the environment
Even when the Emiss ion Control System is op ­
erating properly, the exhaust gas can have a
su lfu r-li ke exhaust gas sme ll under some op­
erating states. Th is depends on the sulfur
content of the fuel being used. Us ing a d iffer­
ent brand of fuel may help, or fi lling the tank
with lead-free super g rade gasoline.
Diesel particulate filter
App lies to: vehicles with diese l engine
The diesel particulate filter filters nearly all of
the soot part icles out of the exhaus t. The filte r
clea ns itself automat ica lly unde r no rma l dr iv ing
cond it ions. If the fil ter canno t clean i tself (fo r ex­
amp le, because yo u are on ly driving short distan­
ces), the filter becomes clogged with soot and
the
II symbol for the diese l particu late filter il­
l uminates
¢ page 20.
A WARNING
- Do not park your vehicle over flammable
materials such as grass or leaves because
the high temperature of the diesel particu­
la te filte r could sta rt a fi re.
-
- Do not apply an underbody protectant in the
exhaust system area or a fire could start.
Shutting down vehicle
If you would like your vehicle to remain inopera­
tive for a longer period of time, contact an Audi
or other spec ia lized dealer . They can adv ise you
o n necessary p recautions e .g. corros ion preven­
tion, ma intenance and storage . Pay attention to
additional informat ion concer ning t he battery.
Refer to
<::;> page 2 31.