2016 AUDI S8 trip computer

Driver information
system
Overview
Fig. 4 Driver information system in the instrumen t cl uster
Fig. 5 Display : example of the information line
The driver information system contains informa­
tion @ that is displayed on tabs@¢ fig.
4. The
following content is possible depending on vehi­
cle equipment:
@
®
Tab Content
1 Vehicle function s:
On-board computer ¢page 24
Efficiency program*¢ page 25
Digital speedomete r
Cruise control*¢ page 88
Adapt ive cruise control and braking
guard* ¢page
90
Audi active lane assist*¢ page 99
Display darkened
Instruments and indicator lights
@ ®
Tab Content
2 Indicator lights and messages
Warn ing when a door, the hood or the
rear lid is not closed ¢ page 28
Service interval display ¢ page
26
Speed warning system ¢ page 88
3 Night vision assistant*¢ page 109
4 Audio/video
s Telephone*
6 Nav igation*
The second and third tabs are only visible if at
least one indicator light or message is shown or if
that system is switched on.
The status line © is located in the bottom part of
the display¢ fig.
4. It displays the exterior tem­
perature, time, selector lever position, tripod­
ometer and odometer.
For some vehicle functions, you can access the
trip information from the temporary memory
¢ page 25 in the line (D ¢ fig. 5.
_& WARNING
--Never rely exclusively on the outside tem­
perature display to determine if a road sur­
face is icy or not. Keep in mind that road
surfaces, especially bridges and overpasses,
could be ice covered and slippery even at an
outside temperat ure above 41 °F (+S °C).
- Always reduce your speed and dr ive with
special care in cold weather conditions when
the chance of encountering icy road surfaces increases .
(D Tips
-You can select the units used for tempera­
ture, speed and other measurements in the
MMI.
- If the vehicle is stationary, or if you are driv­
ing at a very low speed, the temperature
shown in the display might be slightly high­
er than the actual outside temperature . This
is caused by the heat being radiated from
the engine .
lllJ,,
23

Instruments and indicator lights
- For information on the audio/video and nav­
igation* functions, refer to the separate
MMI owner's manual.
Operation
The driver informotion system is operated using
the buttons on the multifunction steering wheel.
::ii
------ -,~
F ig. 6 Multifunction steering wheel: operating the dr iver
infor mation system
Fig. 7 Instrument cluster: opening the vehicle functions
menu
Operating
.,. Switch on the ignition.
.,. To switch between the tabs, press the rocker
switch @to the left or r ight
c:::> fig. 6.
.,. To access additional information below or
above, turn the thumbwheel@ down or up.
.,. To confirm a selection, press the thumbwheel
®·
Opening the Vehicle functions
.,. Se lect the first tab with the rocker switch@.
.,. Press the
l== I button. The Vehicle functions
menu is displayed c:::> fig. 7.
.,. To se lect a menu item, turn and press the
thumbwheel @.
24
~
Resetting values to zero
.,. In the Vehicle functions menu, select On­
board computer
or Efficien cy program .
.,. You can now select between the long-term
memory and short-term memory .
.,. To reset the values in a memory, press and hold
the thumbwheel @for one second.
The last function selected displays when you
switch the ignition on.
@ Tips
Disconnecting the battery causes all the
memory data to be erased.
On-board computer
Fig. 8 Instrument cluster: fuel consumption display
You can call up the following informat ion in the
on-boa rd computer:
- Date
- Dr iving t ime from the short-term memory
- Average consumption from the short-term
memory
- Average speed from the short-term memory
- Distance driven from the short-term memory
- Current fuel consumption
- Short-term memory overview
- Long-te rm memory
overv iew
The short-term memory collects driving informa­
tion from the time the ignition is switched on un­
ti l it is switched off. If you continue driving with­
i n two hours after switching the ignition off, the
new values are included when calculating the cur-
rent trip information.
II>

Unlike the short-term memory, the long-term
memory is not erased automatically. You can se­
lect the time period for evaluat ing trip informa­
tion yourself.
F or some vehicle functions, you can access driv­
ing information from the short-term memory
consecutively in the line ©~
page 23, fig. 5 by
turning the thumbwheel @.
Fuel consumption
The cu rrent fue l consumption can be shown us­
ing a bar graph¢
fig. 8. The average consump­
tion stored in the short-term memory is also dis­
p layed. If the bar is green, your vehicle is saving
fuel through one of the following functions:
- Recuperation : electrical energy can be stored in
the battery when the vehicle is coasting or driv­
ing downh ill. The bar will move toward 0.
-Cylinder on demand system*: the engine auto­
matically switches four cylinders
(4.0L TFS!) or
six cylinders (6.3L FSI) off when lower power
output is required and other conditions are met . This change is not noticeable to the pas­
sengers. The cylinders will switch on again
when higher power output is needed.
Efficiency program
Applies to: vehicles with efficiency program
Fig. 9 T rip computer: o ther equ ipment
Instruments and indicator lights
Fig. 10 Display: example of a fuel economy message
The efficiency program can help you to use less
fuel.
It shows other equipment influenci ng con­
sumption and fuel economy messages provide
tips for efficient driving. The efficiency program
uses distance and consumption data from trip
computer
1.
To display the efficiency program, call up Vehicle
functions
and select the menu option Efficiency
program.
Other equipment
Other equipment that is current ly affecting fuel
consumption is listed in the view
Consumer. The
display shows up to three other items of equ ip­
ment @¢
fig. 9. The equipment using the most
fuel is listed first. If more than three items using
fuel are switched on, the equipment t hat is cur­
rently using the most fuel is displayed.
A scale @also shows the current total consump­
tion of all other equipment .
Fuel economy messages
Fuel economy messages a re displayed when fuel
consumption is increased by certain conditions
~ fig. 10. If yo u follow these fuel economy mes­
sages, you can reduce your vehicle's consumption
of fuel. The messages appear automatically and are only displayed in the effic iency program. The
fuel economy messages turn off automatically
after a certain period of time.
To turn an economy message off immediately af­
ter it appears, press any button on the multifunc -
tion steering wheel. ..,_
25

Instruments and indicator lights
@ Tips
-If the data are deleted in the effic iency pro­
gram, those va lues are also reset in trip
computer.
- Once you have turned a fue l economy mes­
sage off, it will only appear again after you
turn the ign ition on again.
- The fuel economy messages are not dis­
played in every instance, but rather in inter­
vals over a period of time.
Odometer
F ig . 11 Instrument cluste r Odometer and reset button
The odometer shows you how many miles (kilo­
meters) you have driven. You can switch the dis­
play from miles to kilometers and vice versa via
the MMI.
Upper odometer
The trip odometer shows the distance driven
since it was last reset. It can be used to measure
short distances. The last dig it indicates 1/10 of a
mile (100 meters) .
You can reset the trip odometer to zero by press­
ing the Reset button~-
Lower odometer
The lower odometer shows the total numbe r of
miles (kilometers) driven.
Malfunction message
If there is a malfunct ion in the instrument clus­
ter,
DEF w ill appear in the trip odometer display
area . Contact you r a uth orized Aud i dea ler to have
the prob lem corrected .
26
Time and date display
Fig. 12 Center conso le: a nalog clock
The date and time are shown in the instrument
cluster display ¢
page 23, fig. 4. There is also an
analog clock in the center console <=:>
fig. 12.
When you open the driver's door, the date and
time appear in the instrument cluster display for
30 seconds . When the ign ition is switched on,
the time is always displayed in the status line©
regardless of the current disp lay.
You can set the time on both clocks and the date display in the MMI. Refer to the MMI owner's
manual for instructions .
Service interval display
The service interval display reminds you when
your next service is due .
Fig. 13 Instrument cluster : Service interva l display
The service interval display works in two stages:
-Inspection or oil change reminder: After a
specified number of miles, a message appears
in the instrument cluster display when switch­
ing the ignition on or off¢
fig. 13 . The remain-
ing distance or t ime is displayed briefly.
II>