Page 17 of 252

& WARNING
-Never open the hood if you can see or he ar
steam or coolant escaping from the engine
compartment. This inc reases t he risk of
burns . Wa it until you no longe r see or hea r
steam o r coolant escap ing .
- The engine compartment in any veh icle can
be a dangerous area. Stop the eng ine and
allow it to coo l before working in t he engine
compartment . A lways fo llow the informa
ti on foun d in ¢
page 177 .
(D Note
Do not contin ue d riving if the. indicator
light turns o n -thi s increases the r isk of en
gi ne damage.
"t!:r. Engine oil pressure
The red engine oil pressure warning symbol re
quires immediate service or repair . Driving with a
low-oil-pressure indication is likely to inflict se
v e re damage to the engine .
• Turn off engine! Oil pressure is too low.
Tur n off the engine an d do not cont inue d riving .
C hec k the engine oil leve l¢
page 181.
- If the engine oil leve l is too low, a dd engine o il
¢
page 181 . Only cont inue driv ing if the ind i
cator lig ht t urns off.
- If the engine oil leve l is correc t and the i ndica
tor light sti ll tur ns on, turn the eng ine off and
do not continue driving . See you r auth orized
Audi dealer or qualif ied repa ir facility.
@ Tips
-The engine oil pressure symbol. is not
an indicator for a low engine oil level. Do
not rely on it. Instead, check the oil level in
your engine at regular intervals, preferably
each time you refuel, and always before
going on a long trip.
- The yellow oil level warning indication
Ill
requires oil r efill or workshop service with
out delay . Do not wait until the red oil
pressure warning. starts to flash before
you respond to the low oil level warning Instruments and ind
icator lights
IIJ. By then, your engine may already have
suffered serious damage.
0 Battery
The . warn ing/ indicato r light illum inates when
you sw itch on the ig nition and m ust go out after
t h e e ngine has started .
• Alternator fault: Battery is not being charg
ed .
If the indic ator ligh t turns on and the message
appea rs, the re is a ma lfunction in t he generator
o r vehicle e lectr ica l system.
D rive to your au thor ized A udi dealer or qu alified
wor kshop im medi ate ly. Bec au se the vehicle bat
te ry is d ischa rgin g, turn off all u nnecessary elec
t rical eq uipment such as the rad io . Seek p rofes
s iona l assistance if the battery charge level is too
low.
(•) Low battery charge: Battery will be charged
while driving .
If the indic ator ligh t turns on an d the mess age
appea rs, there may be limi ted sta rting abili ty .
If this message turns off after a little whi le, the
ba tte ry ch arge d eno ugh while dr iv ing .
If the message does not turn off, have yo ur au
t h orized Audi de aler or q ual ified works hop cor
r ec t t he ma lf u nct ion.
4t Safety belts
This warning/indicator light reminds you to put
on your safety b elt.
The . war ning/ indicator light illum inates when
t h e ignit io n is switched on to remind t he driver
and any front passenge r to put on the safety be lt.
Addi tionally , a n acous tic w arnin g (go ng) will also
sou nd.
@ Tips
Fo r mor e In forma tion ¢ pag e 104, Saf ety
bel t warning light .
15
Page 18 of 252

Instruments and indicator lights
@-Steering column lock
• Steering fault! Do not driv e vehicle!
If the indicator light turns on and the message
appears, there is an electro nic steer ing colum n
lock malf unct ion . You cannot switch the ign it ion
on.
Do
not tow your vehicle because it cannot be
steered . Seek profess ional assistance .
m Steering lock: System fault ! Plea se contact
d e aler.
If the indicator lig ht turns on and the message
appears, there is an electronic steer ing column
lock malfunct ion.
D rive to yo ur authorized Aud i dea le r i mmediately
to have the ma lfunction corrected .
A WARNING
Your vehicle must not be towed in the event
of a malfunction in the elect ronic steering
co lumn lock because it cannot be steered due
to the locked steering. If it is towed with the
steering locked, there is the r isk of an acci
de nt.
;;,I C; Electronic Stabilization Control (ESC)
If the GI indicato r light b lin ks w hile driving, the
E S C or ASR (Anti-S lip Reg ulat ion) is actively reg u
lating.
I f the
GI indicato r light turns on, the system has
sw itched the ESC off. In this case, you can switch
the ig nition off and t hen o n to switch the ESC on
aga in. The indica tor ligh t turns off when the sys
tem is func tioning fully .
I f the
II indicato r light turns on, ESC was re
s tricted o r swit ched off using the
I .$ OF FI button
~ page 151.
Stabilization control (ESC /ABS): Fault! See
owner 's manual
If the ind icator lig ht I) and the ABS i ndicator
light
D (USA models) ; tlJ (Canada models)
turn on and the message appea rs, the A BS or
e lec tron ic diffe rentia l lock is malfunct io ni ng .
16
This also causes the ESC to malfunc tion. The
bra kes sti ll function with their norma l power, but
ABS is not active .
Drive to your au thor ized A udi d ealer immedi ate ly
to have the mal function cor rected.
A WARNING
If t he 1111 (USA mode ls)/ . (Canada mo d
e ls) bra ke system indicator light turns on to
gethe r with the ABS and ESC ind icator lights,
the ABS/ESC regulating function may have
failed. F unctions that stabilize the vehicle a re
n o longer ava ilab le. This could ca use the vehi
cle to
swerve and increase the risk of slidi ng.
Dr ive ca refully to the nearest au tho riz e d Au di
deale r and h ave the m alfunction correc ted.
© Tips
Fo r addi tional in format ion on ESC and ABS,
r efe r to ~
page 151 .
!I.: Safety systems
The E,I indi cato r light mon itors the safe ty sys
tems (e.g. airbags, pretens io ners) and illumi
nates for a few seconds each t ime yo u switch the
i gnition on .
I f the
E,i ind ic a tor light does not go ou t, or if it
ill umina tes whi le yo u are driv ing , or if it st arts to
blink, the n there is a malfunction somewhere in
the system . If the light does not i lluminate when
yo u sw itch the ignition on, this a lso means there
i s a ma lfunction.
A WARNING
If you have a ma lfunction in the safety sys
tems, contact yo ur authorized Aud i dealer im
mediately. Otherwise the safety sys tems may
not work prope rly in an accident.
(0) Worn brake pads
ll] Brake pads!
If the warning light illuminates, immediately
contact your author ized Audi dealer or qua lified
workshop to have all b rake pads inspected . On
U SA mode ls t he war ning l ight
ll] comes on ..,.
Page 19 of 252

.... N
ci ::, co ....
together with the warning light 1111 . Both se ts
of brake pads on an axle must a lways be replaced
at the same time.
A WARNING
Dr iv ing with bad brakes can ca use a co llision
and ser ious personal in jury.
- If the warning light
EiJ and the wa rning
light
11111> w it h the message Brake pads!
comes o n in the inst rument cluste r display,
immediately contact your authorized Audi
dealer or qualified workshop to have all
bra ke p ads checke d or rep lace d if necessary.
EPC Electronic power control
This warning/indicator light monitors the elec
tronic power control .
-
The [m warning/ indicator light (Electronic Power
Control) ill uminates when you switch the ig nition
on as a function check.
I f th is wa rn ing/indicator light illuminates w hile
you are driving, then there is a malfunct io n in the
engine electronics . Have t he malfunct io n correct
ed as soo n as poss ible by your authorized A udi
deale r or a qua lified re pair facili ty.
o Malfunction Indicator Lamp (MIL)
The Malfu nction Ind icator Lamp (M IL) i s part of
t he On-Boar d Diag nostic (O BD II) syste m. T he
symbo l¢• lights up when the ign ition is swi tc h
ed on and wi ll tu rn off afte r the engine has sta rt
ed an d has sett le d at a constant idle speed. This
ind icates that the MIL is work ing properly.
The warning ligh t illuminates when there is a
malfunct ion in the eng ine e lectron ic system.
Contact your author ized Audi dealer an d have the
mal funct ion corrected.
An imprope rly closed fuel fille r cap may a lso
cause the MIL li ght to illum inate
c:; page 175 .
For mo re informa tio n ¢ page 25.
N
:=: 1) - : USA mode ls onl y
Instruments and ind icator lights
!'? , Engine speed lim itation
Applies to vehicles: with engine speed limitation
II! Do not exceed max. engine speed of XXXX
rpm
The II! symbol illumi nates when t here is an en
gine co ntro l ma lf u nct io n. Th e
[m indicator light
i n th e i nstr ument clus ter also illumi nates. The
engi ne speed is l imited to the speed displ aye d in
t h e d river informat ion sy stem . K eep in min d that
t h e engine speed w ill not exceed the va lue dis
played in the d river info rmation system, for ex
amp le when downshifting.
Dr ive to your authori zed A udi dea ler imme diate ly
to have t he mal func tion cor rec ted.
~ -Engine oil level
1!1;111 Check oil level.
If the indic ator ligh t an d the message appea r,
add engi ne oil immedi ately
c:; page 17 9.
~e, Engine oil sensor
•• Oil level sensor: System fault!
If the symbol illumi nat es, c onta ct yo ur au th or
ized Audi de aler a nd h ave the oil sensor ins pect
ed. Unti l yo u have this done, check the oi l leve l
each time you ref uel j ust to be on the safe side
c:; page 181.
~ Tank system
ti Please refuel
If the indicato r light turns on for the first time
and t he message appea rs, the re are about
1.8 - 2.2 gallons (7.0 -8.5 liters) of fuel left in
the tan k. Time to refue l
c:;page 174.
ti Fuel tank system malfunction! Contact deal
er.
If t he indic ator ligh t turns on and this message
appea rs, there is a ma lf u nction in the tan k sys
tem .
17
Page 20 of 252

Instruments and indicator lights
Drive to your authorized Audi dea ler immediately
to have the ma lfunction corrected .
c:> Windshield washer fluid level
Ill Please refill washer fluid.
If the symbol ill uminates, add w indshield was her
fluid to the w indshield washer system .
~ Engine start system
€·I ~ngine start system: Malfunction! Plea se
con tact dealer.
If th e indicator light t urns on and the message
appears, do
not switch the ign ition off because
you may not be ab le to sw itch it on again.
Drive to yo ur a uthorized Aud i dea le r i mmediately
to have the ma lf u nct ion corrected .
Engine start sy stem: Malfunction . Plea se con
tact dealer .
There is a malfunction in the eng ine start system .
Drive to you r authori zed Aud i dea ler immediately
to have the malfunct ion corrected.
~ Defective light bulb warning
If the rtl i ndicato r light turns on, a bulb has
fa iled. The message ind icates the location of the
bu lb.
V ehicle lights: Sy stem f ault!
If the message appears, there is a ma lfunction in
the headlights or light switch.
Drive to yo ur autho rized Audi dea le r i mmedia tely
to have the malf unction corrected .
A WARNING
-Light bu lbs are p ressurized and could ex
plode while they a re being changed caus ing
serious persona l injury.
- Work with due ca re when handling the high
vo ltage section of gas discharge (xenon)
lights* . Failure to do so could result in death
or serious injury.
18
(D Tips
Have the bu lb replaced or the connection re
paired by your authorized A udi Se rvice depart
ment.
i,0 Headlight range control
fl H ea dlight range control: Sy stem fault!
If the symbol II ill uminates, the dynamic head
li ght range contro l is no longer working properly.
Have the system checked and repaired at your au
thorized Audi dea ler .
~O Audi Adaptive Light
App lies to vehicles: wit h Audi adapt ive light
rlJ Audi adaptive light : System fault!
If the indicator light turns on and this message
appears, there is a ma lfunction in the adaptive
li ght system . The headlights still function .
Go to an authorized dealership to have the head
li ghts or the contro l unit for the adapt ive light re
paired.
@:) Light/rain sensor
App lies to vehicles : wit h lig ht/ ra in sensor
£1 Automat ic headlights /wipers: System fault!
If the indicator light turns on and this message
appears, the light/rain sensor is not functioning
correctly.
For safety reasons the low beams are turned on
permanently with the switch in
AUTO . However,
you can continue to turn the lights on and off us
i ng the lig ht switch . You can still contro l all func
tions that are independent of the rain sensor
through the windsh ield wiper lever .
Contact your authori zed Aud i dea ler as soon as
possible to have the problem corrected.
g Adaptive dampers
App lies to vehicles: wit h Audi drive se lect and a daptive damp
ers
R Suspension : System f ault!
The re is an adaptive dampe r mal func tion.
Page 21 of 252

Drive to an authorized Audi dea ler or a uthorized
Audi Service Facility immediately to have the
malfunct ion corrected.
¢ Q Turn signals
Whenever you use the left R or the right B
turn signal, the indicator light blinks. When you
use the emergency flashers, both indicator lights
flash.
If one of the turn signal light bulbs burn out, the
turn signal will blink twice as fast as normal.
Carefully drive to your author ized Audi dealer im
mediately to have the malfunction corrected .
(D Tips
For more information on the turn signals, see
¢page 40.
¢1¢ Trailer turn signal assembly
The indica tor light also blinks if the turn signal is
operated when towing a trailer .
The indicator light. blinks when the turn sig
nal is used, if a trailer has been properly connect
ed to the vehicle .
If one of the turn signal bulbs on the trailer is
burned out or defective, the indicator light will
not blink when you use the turn signals.
(D Tips
For vehicles with a trailer hitch that was in
stalled later according to factory specifica
tions, the trailer turn signal assembly is actu
ated.
Instruments and indicator lights
19
Page 22 of 252

Driver i nf orm ati on sy stem
Driver information
system
Overview
Fig. 4 Disp lay on vehicles with driver information system*
and multifunction steering wheel*
~ N 0 :::, 00 m
Depending on the vehicle equipment, the driver
information system is controlled with either the
buttons on the windshield wiper lever*
r='.> page 21 or wi th the buttons on the mult i
function steering wheel*
r='.> page 21 .
On vehicles w ith a multifunction steering wheel,
the information @ is shown in tabs @. The tabs
are v isible as soon as you press a button on the
multifunct ion steering wheel*.
The instrument cluster display provides informa
tion about:
® Time and date r='.> page 22
Digi tal speedometer
On-board computer
r='.> page 22
Eff iciency program ¢
page 23
Reduced display *
Indicator lights and messages
r='.>p age 11
Warning when a door, the hood or the
luggage compartment lid is open
r='.>page 23
Service interval display ¢ page 25
Cruise control system¢
page 74
Parking system* ¢
page 88
Aud io*
Telephone*
Navigation*
20
© Odometer and trip odometer r='.> page 23
@ Outside temperature, se lector lever posi -
tion* , headlight assist* indicator light
Auto Chec k Contro l
Some functions and vehicle components are
scanned for their operat ing status when you
switch the ignition on and while you are driving.
Malfunctions or requ ired service procedures are
s ignaled audibly and indicated by red and yellow
illuminated symbols and reminders in the dis
play.
A WARNING
-
- Never rely exclus ively on the outside tem
perature display to determine if a road sur
face is icy or not. Keep in m ind that road
surfaces, especially br idges and overpasses,
co uld be ice covered and slippe ry even at an
outs ide temperature above 41 °F (+ S °C).
- Always remember, even if the "snowflake"
symbol (ice warning) does not appear in the
display, black ice co uld be on the road.
- Always reduce you r speed and drive with
special care in cold weather condit ions when
the chance of encountering icy road surfaces
increases.
(D Tips
If the vehicle is stationary, or if you are driv
i ng at a very low speed, t he temperature
shown in the disp lay m ight be slightly higher
than the actual outside temperature. This is
caused by the heat being radiated from the
engine.
Page 23 of 252

...... N
c:i :::J CX)
...... I.Cl U"I
N I.Cl ......
Operation
Operating using the windshield wiper lever
Applies to vehicles: without multifunction steering wheel
--- ®
Fig . 5 Wi nds hield w iper lever : ope rating th e drive r info r
mat io n syste m
Operating
.. Swi tch the ign ition on . The last select function
is d is pl ayed.
,. To swi tch between the on-board compu ter
0 ,
fJ , the eff ic ien cy p rogram ii o r, fo r ex am ple,
the cr uise control system, p ress the
!RESE T I
button @ .
.. To access additional inf ormation below or
above, press the button @down or up.
Recalling indicator lights and messages
.. Press the I RESE TI button @.
Resetting values to zero
,. Se lect a va lue in the desired tr ip comp ute r o r i n
t h e efficiency prog ram .
.. Press and hold the
!RESE T I button @ for at
l east one secon d. All va lues i n the selected on
board computer or in the efficie ncy pro gram
are reset to ze ro .
Driver in forma tion system
Operating using the multifunction steering
wheel
Applies to vehicles: with multifunct ion steering wheel
Fig. 6 Multifu nct io n stee ring w heel: o perat ing th e d rive r
in fo rm atio n system
Fig. 7 D isplay : Car functio ns me nu
~ M N 9 ::> co m
The tab @~ page 20, fig . 4 is disp layed once yo u
press a button on the mu ltifunction steering
whee l.
Operating
.. Switch the ignit ion on. The las t selec t fu nction
is displayed .
.. To switch between the tabs, p ress the button
CD to t he left or right q fig. 6.
.,. To access addit ional information below o r
above, t urn the th umbwheel @down or up .
.,. To confirm a selection, p ress the thumbwheel
@ .
Opening the Car functions
.. Select the first tab with the button (D .
.,. Press the button @. The Car functions menu is
disp layed
q fig. 7 .
.,. To select a me nu item , tu rn and press the
thumbwhee l@ .
.,. To sele ct a func tion p rogra mmed to a steer ing
w heel button, press the but to n
@ . IJ,,
21
Page 24 of 252

Driver information system
Resetting values to zero
.. In the Ca r functions me nu, selec t On-board
computer or Efficiency program.
.. Se lect a va lue in the desired trip comp uter or in
the efficiency program.
.. To reset the values in a memory , press and ho ld
the thumbwheel @for one second.
Assigning a function to a programmable
steering wheel button
.. Se lect the ICAR I button> (Car ) systems *> Ve-
hicle sett ings
> Steering wheel button .
Recalling indicator lights and m essage s
.. Se lect the II ta b.
T he
II tab is only v is ible when there is a t lea st
one ind icator light o r message displaye d. Other
folders a re only visib le if the applicable system is
switched on.
On-board computer
F ig . 8 Disp lay: on -boa rd comp uter mem ory level 1
Operating with the windshield wiper lever*
.. Press t he I R ES ET ! button @ c::, page 21, fig . 5
repeatedly until t he on-board co mputer ap
pears in the display .
.. To ac cess additional con tent, press the b utton
® ·
Operating with the multifunction steering
wheel*
.. Open Car f unct ions and sele ct the On -board
computer
menu i tem c::, page 21 .
.. To access addition al content, tu rn t he thumb
whee l@ c::>page
21, fig. 6 .
22
You can identify which on-board compute r is cur
rently being show n in the display based on the
small
O or fJ .
The on-board computer O c::, fig . 8 is a short
term memory . It co llects driving info rmation
from the time the ignition is switched on until it
i s sw itche d off . If you contin ue dr iving w ith in two
ho urs after switching the ignition off, the new
values are included when calculat ing the current
trip information .
Unlik e the sho rt-term memory, the long -term
memo ry (on-board computer
f) ) is not e rased
automat ica lly . You can select the time per iod for
evaluat ing trip information yoursel f .
You can ca ll up t he follow ing in fo rmat ion consec
u tive ly in on-board computer
O or f) :
-Date
- Ran g e
- Tr avel ti me
- Average cons umption
- Average speed
- Distance
- Current fuel consumption
@ Tips
-Disco nnect ing the bat tery c auses all the
memory data to be erased .
- Inf orma tion on the e ffic iency program
c::, page 2 3.
Time/date display
Fig . 9 In strum ent cluster: t ime a nd date
You can switch between the quartz clock o r the
G PS cont ro ll ed cloc k* depend ing on the vehicle ..,.