2016 AUDI A7 set clock

M N <( I.J "". rl I.O
"' N I.O rl
There must be at least 10 inches (25 cm) be­
tween your chest and the center of the steering
wheel.
If you cannot sit more than 10 inches (25
cm) from the steering wheel, see if adaptive
equipment is available to help you reach the ped­
als and increase the distance from the steering
wheel.
For detailed information on how to adjust the
driver's seat, see
r:::>page 53.
In vehicles with the memory function*, the steer­
ing column settings are stored together with the
seat position.
A WARNING
Improper use of steering wheel adjustment
and improper seating position can cause seri­
ous personal injury.
- Adjust the steer ing wheel column only when
the vehicle is not mov ing to prevent loss of
vehicle control.
- Adjust the driver's seat or steering wheel so
that there is a minimum of 10 inches (25
cm) between yo ur chest and the steering
wheel
r:::>page 127, fig. 144. If you cannot
mainta in this min imum d istance, the a irbag
system cannot protect you properly .
- If phys ica l limitations prevent you from sit­
ti ng 10 inches (25 cm) or more from the
steering wheel, check with your authorized
Audi dealer to see if adaptive eq uipment is
available.
- If the steering wheel is aligned wi th your
face, the supp lemental driver's airbag can­
not provide as much protection in an acci­
dent. Always make sure that the steering
wheel is aligned w ith your chest.
- Always hold the steering wheel with your hands at the 9 o'clock and 3 o'clock posi­
t ions to reduce the r isk of personal injury if
the driver 's airbag deploys.
- Never hold the steer ing wheel at the 12
o'clock posit ion or w ith your hands inside
the steering wheel rim or on the steering
wheel hub. Holding th e steering wheel the
wrong way can cause se rious injuries to the
hands, arms and head if the driver's a irbag
dep loys .
Drivi ng
Easy seat entry
Applies to vehicles: with power steering wheel adjustment
Easy seat entry makes it easier to enter and exit
the vehicle by adjusting the steering column au­
tomatically.
.. In the Infotainment system, select: the ICARI
function button > ( Car) * Systems control but­
ton
> V ehicle sett ings > Se ats> Driver 's se at>
Ea sy se at entry > On .
When easy seat entry is sw itched on, the steering
column goes back up into the park pos ition when
the ignit ion is switched off . After entering the ve­
hicle, the steeri ng column returns to the stored
pos ition once the ig nit ion is switched on.
Starting and stopping
the engine
Starting the engine
The I STAR T ENGIN E ST OPI button switches the
ignition on and starts the engine .
Fig . 8 1 Center console: START ENGINE STOP button
Sta rting the engine
.. Press the brake pedal a nd move the selector
lever to the P o r
N position.
.. Press the
I START ENGINE STOP j button . The
eng ine will start .
.. It is possib le that there will be a slight delay
when starting the engine in diesel vehicles in
colder temperatu res. Therefore, you must hold
the brake pedal down unt il the engi ne starts .
The indicator light turns on whi le the engine is
preheating
m . ...
75

M N <( I.J "". rl I.O
"' N I.O rl
Taking the wheel off/installing the spare
Follow these instructions step-by-step for chang­
ing the wheel.
Fig. 209 Changing a wheel: using the screwdriver handle
(wi th the blade removed) to turn the bolts
Fig. 210 Changing a wheel: alignment pin inside the top
hole
After you have loosened a ll wheel bolts and
raised the vehicle off the ground, remove and re­
p lace the whee l as fo llows:
Removing the wheel
.. Use the hexagonal so cket in the screwdriver
handle
to completely remove the topmost
whee l bolt and set it aside on a
clean surface
¢fig. 209.
.. Screw the threaded end of the alignment pin
from the tool kit hand-tight into the empty bolt
hole
¢fig. 210.
.. The n remove the other wheel bo lts as descr ibed
above .
.. Take off the wheel leav ing the alignment pin in
the bo lt hole
¢0.
Putting on the spare wheel
.. Lift the spare wheel and carefully slide it over
the alignment pin to guide it in place
¢0 .
Emergen cy assistance
.. Use the hexagonal socket in the screwdriver
handle to screw in and tighten all whee l bolts
slightly.
.. Remove the alignment pin and insert and tight­
en the remaining wheel bolt slightly like the
rest .
.. Turn the jack handle counter-clockwise to lower
the vehicle until the jack is fully re leased .
.. Use the wheel bolt wrench to tighten all wheel
bolts firmly
c;, page 256. Tighten them cross­
wise,
from one bolt to the (approximate ly) op­
posite one, to keep the whee l centered.
(D Note
When removing or installing the wheel, the
rim could hit the brake roto r and damage the
rotor. Work carefully and have a second per­
son help you .
@ Tips
Never use the hexagonal socket in the handle
of the screwdriver to loosen or tighten the
whee l bolts.
- Pull the reversible blade from the screwdriv ­
er before you use the hexagonal socket in
the handle to turn the whee l bolts.
- When mount ing tires w ith
unidirectional
tread design
make sure the tread pattern is
pointed the right way
c;, page 259.
-The wheel bolts should be clean and easy to
turn. Check for dirt and corrosion on the
mating surfaces of both the wheel and the
hub. Remove all dirt from these surfaces be­
fore remounting the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right direction .
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a spare tir e with a tread pattern in­
tended for use in a specific direction, please note
the following:
- The direction of rotation is marked by an arrow
on the side of the tire . .,.
259