2016 AUDI A4 warning

Light and Vision
Rear window sun shade
Applies to vehicles: with rear window sun shade
Fig. 52 With MMI: Button for rear window sun shade
F ig. 53 Withou t MMI: Button for rear window sun shade
• To extend/retract the sun shade, press the [iii)
button ¢ fig. 52 or ¢ fig. 53.
You can adjust the settings for the rear sun shade
so the shade retracts automatically when you se­
lect the reverse gear. To do th is, select the
I CAR !
function button>
Window s> Rear blind > auto­
matic > on
or! CAR ! function button> C ar sy s­
tem s*
control button > Vehicle settings > Auto­
matic rear blind > On .
The current se tting is au­
tomatically stored and assigned to t he remo te
key. The sun shade is extended again as soon as
the vehicle is traveling forward at a speed greater
than 9 mph (15 km/h) if the ignition has not
been switched off in the meant ime.
A WARNING
Whe n lowering or ra is ing the sunshade, make
sure there is nothing in its way and that it has
a free path to travel. This could cause person­
al injury.
54
@ Tips
- Pressing the button~ several times con­
secut ive ly can t rigger the overload protec­
t ion. The sun shade can only be extended/
retracted again after a brief wait ing per iod .
- The rear window sun shade o nly functions
when the veh icle inter ior is warmer than
14°F (-10°C).
Windshield wipers
Switching the windshield wipers on
f
• ®
• @
·®
• @
•®
Fi g. 54 Windshield wiper lever
* (!) ~ @
Fig. 55 allroa d: Rear wipe r actuat ion
Move the windshie ld w iper lever to the co rre­
sponding posi tion:
@ -Windshie ld w iper off
0
0
~
"'
" r-~ 0 :::, @ -Interval mode. To extend/shorten the w iper
i ntervals, move the switch @ to the left/right. In
vehicles with a rain sensor* the wipers turn o n in
the rain once the vehicle speed exceeds approx i­
mately 2 mph (4 km/h). The higher the sensitivi-
ty of the rain senso r* is set (sw itch @ to the
r ight), t he earlier the wi ndshield wipe rs reac t to
moist ure on the w indshield. In some models, yo u ..,.

..... N
0 ::..:: co ..... ..... can switch rain sensor mod e off and sw itch int er­
mi ttent mode on in the MMI*. Select: I CARlfunc­
tion button
> Ca r sys te m s* control button > Driv·
er a ssist
> Ra in se nsor . In interm ittent mode,
you c an adju st the interva l time u sing the @
switch .
@-Slow wiping
@-Fast wiping
© -Sing le wipe
® -Clean the windshield . To elimina te w ater
droplets, the windshield wiper performs one af­
terwipe operat ion after several seconds while
driving . You can sw itch this function off by mov­
i ng the lever to position ® within
10 seconds of
the afterwipe operat ion. The afte rw ipe funct io n
is reactivated the next t ime the ignit io n is switch­
ed on.
allroad: The rear wiper automatically switches on
when the reverse gear is engaged and the fro nt
windsh ie ld w ipers are on and in operation .
C lean ing the headlights* . The headlight washer
system* ope rates on ly when t he headlights a re
on .
If you move t he leve r to pos ition ®· the
h eadligh ts a re washed in intervals.
@ -allroad: Wipe the rear window . The rear wip­
e r moves about every 4 seconds.
(J) -allroad: Clean the rear window . The number
of wip ing operations depends on how long the
lever is held in posit ion
(J) .
A WARNING
- T he rain senso r is only intended to assist the
dr iver. The driver is still responsib le for
man ua lly switching the wipers on accord ing
to the visibility conditions.
- T he windshie ld may not be treated wi th wa­
ter -repell ing windsh ield coa ting agents . Un­
favorable conditions, s uch as wetness, dark­
ness, low sun, can result in increased glare.
Wiper blade chatter is also possible .
- Properly function ing windshield wiper
blades are required for a clear view and safe
dr iv ing ¢
page 56, Replacing windshield
wiper blades .
Light and Vision
(D Note
-In the case of frost, check whether the
w indshield wiper blades are frozen to the
w indshield. Switching on the w indshield
w ipers can damage the w iper blades!
- Pr ior to using a car wash, the w indshield
w iper system must be sw itched off (lever in
position @). This helps to prevent un inten­
tional switch ing on and damage to the
w indshield wiper system .
(D Tips
-The windshie ld w ipers are switched off
when the ig nit ion is turned off . Act ivate the
w indshield wipers after the ignition is
switched back on by moving the w indshield
w iper lever to a ny position.
- Worn or dirty windshie ld w iper blades resu lt
in st reaking. This can affect the rain sensor*
function. Che ck your w indshield w iper
blades reg ularly.
- T he washer f luid noz zles of the w indshie ld
washer system a re heated at low tempera­
t u res when the ign ition is on .
- When s topping tempo rar ily, (e .g . at a t raf­
fic ligh t) the set speed of the winds hield
wipers is a utomatically reduced by one
speed .
Cleaning windshield wiper blades
Clean the windshie ld wipe r blades when they be­
gin to leave st reaks. Use a soft cloth and gla ss
cleaner to clean the windshield wiper blades.
Front wip er
.,. Place the windshie ld wiper arms in the service
position. R efe r to
c::> page 56 .
.,. Lift the w iper a rm away from the front window.
Rear wiper*
.,. Lift the w iper arm away from the rear w indow .
A WARNING p.----
Dirty windshie ld wiper blades can impair yo ur
v iew. This can lead to accidents .
55

Lig ht a nd Visio n
Replacing windshield wiper blades
Fig. 56 Re mov ing w indshi eld w iper blade
Wiper service po siti on/b la de r eplac em ent
po sit ion
• Switch the ignition off and move the windsh ield
wiper lever to position @
Q page 54, fig. 54 .
The w indshield wipers move into the service po­
sition.
• To bring the wipers back into the or iginal pos i­
tion, switch the ignition on and press the wind­
shield w iper lever.
You can a lso turn the service position on or off in
the radio/MM!*:
• Switch the windshield wipers off (position @
Qpage 54, fig. 54) .
• Select : ICARI function button > Windshi eld
wi pers > Servic e posit ion > on/off .
Or
• Select :
I CARI funct ion button > C ar syst ems*
control button > Servici ng & ch ecks > W ip er
se rvic e po sition
> O n/Off .
R emo ving th e wiper blad e
• Lift the w indshield w iper arm up from the
windshield.
• Press the locking knob
(D Q fig. 56 on the wiper
blade . Hold the wiper blade firmly .
• Remove the wiper b lade in the direct ion of the
arrow.
Attaching th e wiper blade
• Install the new wiper blade in the reta iner on
the wiper arm @untilyou hear it click into
place on the wiper arm .
• Place the w iper arm back on the w indshie ld.
• Turn the service position off.
56
A WARNING
For your safety, you should replace the wiper
blades once or twice a year . See your author­
ized A udi dealer for replacement blades.
(D Note
- The windshield w iper blades must only be
replaced when in the service pos ition! Oth­
erwise, you r isk damaging the paint on the
hood or the w indshield wiper motor .
- You should not move your vehicle or press
the windsh ield wiper lever when the wiper
arms are folded away from the windshie ld.
T he windshield w ipers would move back in­
to their original pos ition and co uld damage
the hood and windshie ld.
- T o help prevent damage to the wiper sys­
tem, always loosen blades which a re froze n
to the windshield before operat ing wipers.
- T o help prevent damage to w iper blades, do
not use gasoline, ke rosene, paint th inner, or
other solvents on or near the wiper blades.
- T o help prevent damage to the wiper arms
or othe r componen ts, do no t at tempt to
move the wipers by hand.
(l} Tips
- Commercia l hot waxes applied by automatic
car washes affect the how easily the glass
surface can be cleaned.
- You can also use the service pos it ion, for ex­
ample, if you want to protect the windshield
from icing by using a cover .
Replacing the rear wiper blade
Applies to vehicles: with rear wipe r
Fig . 57 Rear wipe r: Remov ing t he w ipe r blade

,....,
N
0
""' CX) ,....,
I.Cl U"I ,....,
I.Cl ,....,
Removing the wiper blade
• Fold the windshield wiper arm away from the
windshield.
• Pull the wiper blade and holder out of the
mount.
Attaching the wiper blade
• Press the wiper b lade holder in the arrow di rec­
t ion
r::!> fig . 57 into the mount .
• Fold the windshield wiper arm back onto the
windshield.
A WARNING
For safety reasons, the windshield wiper
blades should be replaced once or tw ice each
year.
Digital compass
Switching the compass on and off
Applies to vehicles: with digital compass
The compass direction is shown in the rearview
mirror.
F ig . 58 Rea rview mirror: Digita l compass ac tivated
• To switch the compass on or off, press and hold
the button @until the compass display in the
mirror
r::!> fig. 58 appears or disappears.
The digital compass only works when the ignition is on. The directions are indicated with abbrevia­
tions :
N (north), NE (northeast), E (east), SE
(southeast) , S (south), SW (southwest), W
(west), NW (northwest) .
Light and Vision
(D Tips
To prevent inaccurate compass readings, do
not bring any remote controls, electrical devi­
ces or metallic objects near the mirror.
Adjusting the magnetic zone
Applies to vehicles: with digital compass
The magnetic zone must be adjusted correctly
for the compass to read accurately.
®
Fig. 59 North A meri ca: magnetic deflect io n zone bounda­
ries
" Press and hold the button@r::!> fig. 59 until the
number of the magnetic zone appears in the
rearview mirror.
" Press the button @ repeated ly to select the
correct magnetic zone. The selection mode
turns off after a few seconds .
Calibrating the compass
Applies to vehicles: with digital compass
You must recalibrate the compass if it does not
display the correct direction.
" Press and hold the button @until a C appears
in the rearview mirror.
• Dr ive in a circle at about 6 mph (10 km/h) until
a direction is displayed in the rearview mirror. ..,.
57

Light and Vi sion
A WARNING
- To avoid endangering yourself and other
drivers, calibrate the compass in an area
where there is no traffic .
- The digital compass is to be used as a d irec­
t ional aid only . Even though you may want
to look at it while you are driv ing, you must
sti ll pay attention to traffic, road and
weather cond itions as well as other possible
hazards.
5 8

..... N
0 :,,:: co ..... ..... Seats and storage
General information
Why is your seat adjustment so important?
The safety belts and the airbag system can only
provide maximum protection if the front seats are corr ectly adjusted.
There are various ways of adjusting the front
seats to provide safe and comfortable support
for the driver and the front passenger. Adjust
your seat properly so that:
- you can easily and quickly reach all the switches
and controls in the instrument panel
- your body is properly supported thus reducing
physical stress and fatigue
- the safety belts and airbag system can offer
maximum protection
Q page 138.
In the following sections, you will see exact ly
how you can best adjust your seats.
There are spec ial regulations and instr uctions for
installing a child safety seat on the front pas­
senger's seat. Always fo llow the information re­
garding child safety provided in
¢page 158,
Child safety.
A WARNING -
Refer to Q page 121, Driving safety for im­
portant information, tips, suggestions and
warnings that you should read and follow for
your own safety and the safety of yo ur pas­
senge rs.
A WARNING
Incorrect seat ing position of the driver and all
other passengers can result in serious person­
al injury .
- Always keep yo ur feet on the floor when the
vehicle is in motion -never pu t your feet on
top of the instrument pane l, out o f the win ­
dow or on top of the seat cushion. This ap­
plies especially to the passengers. If your
seating pos it ion is incorrect, you increase
the risk of injury in the case of sudden brak­
ing or an accident. If the airbag inflates and
Seat s and sto rage
the seating position is incorrect, this could
result in persona l injury or even death.
- It is important for both the driver and front
passenger to keep a distance of at least
10 inches (25 cm) between themselves and
the steering wheel and/or instrument pan­
el. If you're sitt ing any closer than this, the
airbag system cannot protect you properly.
In addition, the front seats and head re­
stra ints must be adjusted to you r body
he ight so that they can g ive you maximum
p rotection.
- Always try to keep as much dis tance as pos­
sible between yourself and the steer ing
wheel or instrument pane l.
- Do not adjust the driver's o r front passeng­
er 's seat while the veh icle is moving . Your
seat may move unexpectedly, causing sud­
den loss of vehicle contro l and personal in­
jury. If you ad just your seat while the veh icle
is moving, you are out of pos ition.
Driver's seat
The correct seat position is important for safe
and relaxed driving.
We recommend that you adjust the dr iver's seat
in the following manner:
.,. Adjust the seat in fo re and aft direction so tha t
you c an ea sil y push the pedals to the floor
while keeping yo ur knees s light ly bent¢ .&.
in
Why is your seat adjustment so important? on
page 59.
.,. Adj ust the seatback so that when you sit with
your back against the seatback, you can still
grasp the top of the steering wheel.
.,. App lies to ve hicles w ith ad justab le head re­
stra ints: Adjust the head rest raint so the upper
edge is as even as possible w ith the top of your
head. If t hat is not possible, try to adjust the
he ad restraint so that it is as close to this pos i­
tion as possible ¢
page 61.
A WARNING ~
Never place any objects in the driver's foot-
well. An object could get into the pedal area and interfere with pedal function. In case of
59

Sea ts and stor age
sudden braking or an accident, you would not
be able to brake or accelerate.
Front passenger's seat
Always move the front passenger seat into the
rearmost position.
To avoid contact with the a irbag while it is de­
p loying, do not sit any closer to the instrument
panel than necessary and a lways wear the three­
point safety belt provided adjusted correctly. We
recommend that you adjust the passenger's seat
in the following manner:
.,. Bring the backrest up to an (a lmost) upright
position .
Do not ride with the seat reclined.
.,. Applies to vehicles with adjustable head re­
straints: Adjust the head restra int so the upper
edge is as even as poss ible with the top of your
head. If that is not possible, try to adjust the
head restraint so that it is as close to th is posi­
tion as poss ible
~ page 61.
.,. Place your feet on the floor in front of the pas­
senger's seat.
Front seats
Manual seat adjustment
App lies to veh icles : with manually adjustable seats
F ig . 60 Fro nt seats: man ual seat adjustment
Controls
@ -Moving the seat forwa rd/back : pull the lever
and slide the seat~&..
@ -Lengthen ing/shortening the upper thigh
suppor t* : lift the handle. A spring moves the sup­
port forward ~.&. .
60
@ -Adjusting the a ngle* of the seat surface:
pull/press the lever ~.&. .
@ -Adjust ing the lumbar support*: p ress the
b utton in the cor responding position~,&.
®-Moving the seat up/down : pull/press the lev­
e r ~ .&. -
@ -Adjusting the backrest ang le: turn the ad­
justing wheel~&. .
& WARNING
-Never adjust the drive r's or front passeng­
er 's seat while the veh icle is moving. If you
do t his while the veh icle is moving, yo u will
be out of posi tion . Always ad just the d river 's
or front passenger's seat when the vehicle is
not moving.
- Be carefu l when adjust ing the seat height.
Check to see that no one is in the way, or se­
rio us injury could result!
- To reduce the risk o f injury in the case of
sudden braking or accident, front passen­
ge rs must never ride in a moving veh icle
with the backrest reclined. Safety belts and
the airbag system only offer maximum pro­
tect ion when the backrest is upr ight and the
safety belts are properly positioned on the body. T he more the backrest is reclined, the
greater the risk of pe rsonal inj ury from an
incor rec t seating posi tion and improperly
posi tioned safety belts.
Power seat adjustment
Applies to vehicles : with power adjustable seats
Fig. 61 Fro nt seats: powe r seat adjustment
-

...... N
0
""' CX)
...... I.Cl U"I
...... I.Cl ......
Controls
@-Adjusting the lumbar support*: press the
button in the corresponding position¢.&. .
@ -Moving the seat up/down: press the button
up/down¢ .&_.
@ -Moving the seat forward/back: press the but­
ton forward/back¢ .&,.
©-Adjusting the backrest angle: press the but­
ton forward/back¢ .&..
©-Raising/lowering* the head restraints: press
the button up/down
c:> .&. .
@ -Lengthening /short ening the uppe r thigh
support*: lift the handle. A spring moves the
front seat cushion forward
c:> .&..
A WARNING
-Never adjust the driver's or front passeng­
er's seat while the vehicle is moving. If you
do this while the vehicle is moving, you will
be out of position. Always adjust the driver's
or front passenger's seat when the vehicle is
not mov ing.
- Be careful when adjusting the seat height.
Check to see that no one is in the way, or se­
rious injury could result!
- Because the seats can be electrically adjust­
ed with the ignition off or with the ignition
key removed, never leave children unattend­
ed in the vehicle. Unsupervised use of the
electric seat adjustments may cause serious
injury.
- To reduce the risk of injury in the case of
sudden braking or accident, front passen­
gers must
never ride in a moving vehicle
with the backrest reclined. Safety belts and
the airbag system only offer maximum pro­
tection when the backrest is upright and the
safety belts are properly positioned on the body. The more the backrest is reclined, the
greater the risk of personal injury from an
incorrect seating posit ion and improperly
positioned safety belts .
-
Seats and storage
Center armrest
The center armrest can be adjusted to several
levels .
Fig. 62 Armrest between the driver 's/front passenger's
seats.
Adjusting the center armrest
... To adjust the angle, raise the armrest from the
starting position
c:> fig. 62 detent by detent.
... To bring the armrest back into the starting po­
sition, raise it out of the top detent and fold it
back down .
The armrest can slide forward and back.
Head restraints
Front head restraints
Appl ies to vehicles: wi th adjus tab le head restrain ts
Head restraints that are adjusted according to
body size, along with the seat belt, offer effec­
tive protection.
Fig. 63 Front seat: adj usting the head restrain ts
Adjust the head restraint so the upper edge is as
even as possible with the top of your head . If that
is not possible, try to adjust the head restraint so
that it is as close to this position as possible
¢page 61 .
61