2016 AUDI A4 headliner

Opening and clo sin g
Convenience opening /clos ing
The windows and the power sunroof can be
opened and closed with the mechanical key or
the emergency key.
®
'
l
® '
Fig . 35 Key turns for opening an d clos ing
Convenienc e opening f eature
.,. Use the eme rgency key or pu ll the mechanical
key out of the master key
¢ page 33 .
.,. Insert the key into the lock of the driver's door .
.,. Turn the key to position ¢
fig. 35 ® until all
the windows have reached the desired position
and the power sunroof is open .
Convenience cl osing fea tur e
.,. Use the emergency key or pull the mechanical
key out of the master key
q page 33.
.,. Turn the key in the lock of the driver's door to
the lock position @ until the windows and the
power sunroof are closed
q _&..
For vehicles with Panoramic sliding sunroof*:
When you open or close the Panoramic sliding
sunroof*, the power sunshade will also open or
close.
A WARNING
- Never close the windows and the power s un­
roof inattent ively and without checking -
there is risk of injury.
- Yo u m ust always watch when the w indows
are be ing raised so that no one can be trap­
ped. If you release the key, the closing ac­
t ion is immediately cance led.
- Always read and heed WARNING
9 & in
General description on page 31 .
42
Correcting window regulator malfunction
After disconnecting the vehicle battery, the one­
touch up and down feature must be activated
agam .
... Pull and hold the power window sw itch until
the window is completely closed .
... Release the switch and pull the switch again for
one second.
Sunroof
Operation sliding /tilting sunroof
Applies to vehicles: with sliding/tilt ing sunroof
Fig . 36 Section of headliner: knob for sunroof
Tilting
Requirement: the roof switch m ust be in the @
pos ition
q fig. 36 .
... To t ilt it, briefly press the switch ¢ fig . 36.
... To close it, b riefly pull the switch 9 _&. .
:g N
N
•
" CD m
... To set an intermed iate position, p ress/p ull the
sw itch un til the roof reaches the desired posi­
tion.
Opening /slid ing
... To slide the roof all the way open, tur n the
sw itch to the
(D position.
... To close the s unroof complete ly, turn the
sw itch to @ position
<=? _&..
... To select a setting in between, turn the sw itch
to the desired position.
The sunshade can be opened and closed manual­ l y in any position . W hen opening the sunroof , the
sunshade is a utomatically opened.
After the ignition is switched off, yo u can st ill op­
erate the su nroof fo r abo ut 10 m inutes. As soon .,.

.... N
0
""' CX)
.... I.Cl U"I
.... I.Cl ....
as the driver's or passenger's door is opened, the
switch is inoperative .
A WARNING
Pay careful attention when closing the sun­
roof -otherwise serious injury could result!
For this reason, always remove the ignition
key when leaving the vehicle.
CD Note
Always close your sunroof when leaving your
vehicle. Sudden rain can cause damage to the interior equipment of your vehicle, particular­
ly the electronic equipment .
(D Tips
-Information on convenience opening/clos­
ing
c:> page 42.
Operation panorama sunroof
Appl ies to vehicles: with pa nora ma sunroof
Fig . 37 Sectio n fro m headliner: knob for sunroof.
Tilting
• The sunroof can be ti lted or closed only in
switch position @c:>
fig. 37
• To tilt it, briefly press the switch c:> page 42,
fig. 36.
• To close it, briefly pull the switch c:> &_ .
• To set an intermediate position, press/pull the
switch unt il the roof reaches the desired posi­
t ion.
Opening
• To open the sunroof completely, turn and hold
the switch against the resistance in position
Q) .
• To close the sunroof, tur n the rotary sw itch to
pos ition @~&_ .
Open ing and closing
• An intermediate position can be set by turn ing
the rotary switch to the desired position.
Opening/closing the sunshade
• Press the switch @c:> page 42, fig. 36 in the
desired arrow direction.
• To stop the sunshade in an intermediate posi-
tion, press the switch again.
After the ignition is sw itched off, you can still op­
erate the sunroof for about 10 minutes. As soon
as the driver's or passenger's door is opened, the
switch is inoperative.
The power sunshade can also be closed when the
sunroof is open.
A WARNING ~ ~
Pay careful attention when closing the sun­
roof -otherwise serious inju ry could result!
For this reason, always remove the ignition
key when leaving the vehicle.
CD Note
Always close your sunroof when leaving your
vehicle . Sudden rain can cause damage to the
interior equipment of your vehicle, particular ­
ly the electronic equ ipment.
({D Tips
- Information on convenience opening/clos­
ing c:>
page 42.
Emergency closing of the sunroof
If the sunroof detects an object in its path when
it is closing, it will open again automatically. In
th is case, you can close the roof with the power
emergency closing function .
• Within five seconds after the sunroof opens au­
tomatically, pull the sw itch until the roof
closes.
43

Opening and clo sin g
Valet parking
Applies to vehicles: with folding and lockable rear seatbacks
The valet parking feature protects the luggage
comportment from unauthorized access .
-
Fig. 38 Glove compartment: valet park ing button
You can sw itch the "va let park ing funct ion" on
when someone else is pa rk ing you r vehicle. When
the function is sw itched on, the vehicle can be
driven, locked and un locked using the master
key, but access to the luggage compartment is
not permitted .
• Take the mechanical key ou t of the master key
<=> page 33.
• Open the glove compartment r::!> page 66 .
• Activate
¢ fig. 38 the "valet parking" feature by
pressing the
! VALET I button. The indicator light
in the switch illuminates.
• Close the glove compartment and lock it with
the mechanical key.
• Lock both rea r seatbacks w ith the mechan ica l
key
¢ page 69.
• Lock the luggage compar tment pass-through
with the mechanical key<=>
page 74 .
• Leave the master key with the service personnel
for parking and keep the mechanical key with
you.
The fo llowing buttons are deactivated when the
valet parking function is switched on:
- 1""' 1 bu tton in the dr iver's door
- I a I button on the master key
- Handle in the rear lid
When the valet parking feature is activated, the message
V alet park ing activ ated appears in the
instrument cluster display when you switch the ignit ion on .
44
Garage door opener
(Homelink)
Description
Applies to vehicles: with garage door opener (Horne Link)
Fig. 3 9 Garage doo r opene r: exa mples of using w it h d iffer·
ent syste ms
You can act ivate vario us systems suc h as garage
doors, secur ity systems and home lighting from
inside your vehicle using the garage door opener
(Homelink) . There are three buttons for th is in
the veh icle headliner that can be in used in place
of up to three hand-held transmitters.
To operate systems using the garage door open­
er, the three buttons in the roof headliner must be programmed first .
A WARNING
Make sure no people or objects are in the im­
mediate vi cinity of the equipment when using
or p rogramm ing the ga rage door opener. Peo­
pl e can be injured and ob jects can be dam­
aged i f they are caught in the equipment.
(D Tips
- For sec urity reasons, we recommend that
yo u clear the prog rammed but tons before
sell ing t he ve hicl e.
- For add itiona l information about HomeL ink,
visit www.homelink .com .
- For Declaration of Compliance to United
States FCC and Indust ry Canada regulat ions
<=>page 261.

.... N
0
""' CX)
.... I.Cl U"I
.... I.Cl ....
Operation
Applies to vehicles: with garage door opener (Homelink)
·-
~ •• r ·O : o ··) ,,;~
®
~ (_ 0_1 J c:cc
F ig. 40 Headl iner: c on tro l uni t
Requirement: The buttons in the roof headliner
must be programmed
c:> page 45 or
c::> page 46 and the vehicle must be within
range of the system, such as the garage door
opener.
" Press the button to open the garage door . The
LED @blinks or turns on .
" Press the button again to close the garage
door .
@ Tips
To open or close the garage door, press the
button, but do not hold it for longer than
10 seconds or the garage door opener module
w ill switch to programming mode.
Programming the buttons (version A )
Applies to vehicles: with garage door opener (Homelink)
You can program both fixed code and rolling code
systems using this procedure .
Programming or reprogramming buttons
"Switch the ignition on.
"P ress and hold the button in the roof headliner
c::> page 45, fig. 40 that you would like to pro­
gram for at least 10 seconds. Or
.. Select:
I CAR I function button > Car systems*
contro l button > Vehicle settings > Garage
door opener> Program garage door opener . If
th is path is not available, program the button
as described in version B
c::> page 46 .
"Fol low the instructions in the MMI.
Open ing and closing
Erasing button programming
The programmed buttons can not be erased ind i­
vidually . They must all be erased together. Re­
program the buttons if necessary.
" Select:
!CAR ! function button> Car systems*
control button > Vehicle settings > Garage
door opener > Clear program settings > Yes.
Displaying the version/status/country code
" Select: !CAR ! function button> Car systems*
cont rol button > Vehicle settings > Garage
door opener > Version information .
(D Tips
-Programming through the MMI* is not pos­
sible with all infotainment systems. If this
is the case, program the buttons as descri­
bed in version B
c::> page 46.
- Th e required distance between the hand
transmitter and the Homelink module in
the radiator grille
c::> page 46, fig. 41 de­
pends on the system that you are program­
ming.
- Depending on the model of the system, you
may need to release the button on the re­
mote control during programming and
press it again. Hold each position you try for
at least 15 seconds before trying another
posit ion . Keep the turn s ignals on your vehi ­
cle in view when doing this.
- After programming the garage door opener,
it may be necessary to synchronize the mo­
tor with the system. Refer to the manufac­
turer's instructions.
45

Opening and clo sin g
Programming the buttons (version B)
Applies to vehicles: with garage door opener (Homelink)
Fig. 41 Dist an ce betwee n th e rad iator g rille an d th e hand
tra nsm itt er
Programming the button : Part 1 with the
contr ols
1. Switch the ignition on.
2. Press and ho ld both outer b uttons in the roof
headliner ~
page 45, fig. 40 until the LED @
turns off completely (after about 20 sec­
onds). This procedure clears the s tandard co­
des that were set at the factory and does
not
need to be repeated again to program the
other buttons .
3. Br iefly p ress the b utton o n the roof headliner
that you wou ld like to program .
4. Wa it until the LED @ begins to blink quickly .
Programming mode is active for 5 minutes .
5. Move in front of yo ur vehicle while holding
the original remote control for the system
t hat would like to program to a button in the
roof headliner.
Prog ramming th e butt on : Part 2 at the
r a d iat or gr ille
6. Ho ld the remote control up to the radiator
grille on your vehicle¢
fig. 41 .
7. Press and hold the remote control until the
turn signals on your vehicle blink . This may
take up to 30 seconds.
8 .
If the emergency flashers blink th ree t imes,
the programming was suc cessful.
If th e
emergency flashers only b lin k one t ime , the
5 minute time limit for t he p rogramming has
ended or the programm ing was not success­
fu l. Repeat the programming from the third
step, or try changing the distance to the radi­
ator grille.
46
9 . If the garage door or other system does not
op en using the buttons in the roof headliner
even though the programming was success­
ful , the system may use a ro lling code in­
s tead of a fixed code .
Rolling code prog ram­
m ing
must be performed ¢ page 47.
The other two b uttons in the roof head liner can
be programmed according to the instruct ions
above . Begin with the third s tep .
Era sing button prog ramm ing
The prog rammed buttons cannot be erased indi­
vidually . They must a ll be erased tog ether . Re­
program the buttons if necessary .
.. Switch the ignit io n on.
.. Press and hold both outer bu ttons in the roof
headliner until the LED @turns off comp lete ly
( after about 20 seconds).
Reprogramm ing the buttons
.. Switch the ignit io n on .
.. To reprogram an individual button, press and
hold the button unti l the LED @starts to flash
quickly (after about 10 seconds) . Release the
button immed iately. Programming mode is ac­
tive for 5 m inu tes.
.. Continue with the fifth step.
@ Tips
- Programming using the buttons in the roof
headliner is not possible with all Infotain­
ment systems . If this is the case, program
the buttons as descr ibed in version A
¢ page 45 .
- The required distance between the hand
transm itte r and the Homelink module in
the radiator grille~
fig. 41 depends o n the
system that you are prog ramming.
- Depending on the mode l of the system, you
may need to release the b utton o n the re­
mote contro l dur ing programm ing and
press it again. Hold each position yo u try for
a t least 15 seconds before trying another
posit ion . Keep the turn s ignals on your vehi­
cle in view when doing this .

Rolling code programming
Applies to vehicles: with garage door opener (Homelink)
Rolling code programming is also needed for
some systems.
Ident ifying a rolling code
~ Press and hold the button in the roof headliner
that was already programmed .
~ Watch the LED@¢ page 45, fig. 40. If the LED
blinks quickly, the systems (such as a garage
door) is equ ipped with a roll ing code .
~ Program the rolling code as follows:
Acti vati ng the motor unit in a system
~ Locate the programming button on the sys­
tem's motor unit. The exact location and color of the button may vary depending on the brand
of the system.
~ Press the programm ing button on the garage
door opener motor unit (th is w ill usually acti­
vate a n "indicator" on the moto r unit). You now
have approximate ly
30 second s to program the
button in the roof headliner .
Programming the button in the roof
h eadline r
~ Press and hold the previously programmed but ­
ton in the roof headliner for 2 seconds.
~ To end rolling code programming, press and hold the button again for 2 seconds.
~ With some systems, the button may need to be
pressed a third time to end the programming
process .
After programming, the system should detect
the signal and beg in mov ing when the button in
the roof headliner is pressed . Now you may pro­
gram the other buttons as needed.
(D Tips
- The rolling code can be programmed more
quickly and more easily with the help of a
second person.
- If you have difficulty programm ing the roll-
,.... ing code, referring to the user guide for the
N
~ system may help.
co ..... ..... Op ening and cl osing
47

..... N
0
""' CX)
..... I.Cl U"I
..... I.Cl .....
Interior Lighting
Front/rear interior lights
(• ' .,;,I
~~~
8 8
O. ~O
l
Fig. 45 Front headl iner : interio r lighting co ntrols
Fig. 46 Rear headliner : rear re ading lights
@Interior lights
Press the switch Qfig . 45 in the corresponding
position .
0 -Interior lights off
I - Interior lights on
If the switch is in the center position, the interior lighting is controlled automatically .
@ Front/rear re ading lights
To turn a reading light on/off, press the button
~ Q fig. 45 or Q fig. 46.
The appearance and location of the rear reading
lights may differ depending on the model.
Light and Vision
Instrument illumination
The basic brightness of the illumination for the
instruments, the center console and the display
can be adjusted .
Fig. 47 Instrume nt illumin atio n
• Press the knob to release it .
• Turn the knob toward"- " or"+" to reduce or in­
crease the brightness .
• Press the knob again to return it to its o riginal
position .
@ Tips
The instrument illumination (for dials and
needles) lights on when the ignition is switch­
ed on and the vehicle lights are turned off. As
the daylight fades, the illumination of the di­
a ls likewise dims automatically and will go
out completely when the outside light is very
low. This feature is meant to remind you to
switch on the headlights when outside light
conditions become poor.
Vision
Adjusting the exterior mirrors
Fig. 48 Driver 's doo r: kno b fo r the exterio r mirrors
Turn the knob to the desired position :
51