2015 SUZUKI NEXA ignition
[x] Cancel search: ignitionPage 208 of 288
Downloaded from www.Manualslib.com manuals search engine 2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
The anti-theft function is intended to dis-
courage thefts, such as that the audio sys-
tem becomes inoperable when it is installed
on other vehicles.
This function works by entering a Personal
Identification Number (PIN).
When the unit is disconnected from its
power source, such as when the audio sys-
tem is removed or the battery is discon-
nected, the unit will become inoperable until
the PIN is reentered. 6 H W W L Q J W K H $ Q W L 7 K H I W ) X Q F W L R Q1) Press the VOL PUSH POWER knob (1)
to power off.
2) Hold down the buttons numbered [1]
and [6] of the Preset buttons (2) and
press the VOL PUSH POWER knob (1).
“SECURITY” will be displayed.
3) Press the Up button (3) and the button
numbered [1] of the Preset buttons (2)
simultaneously.
4) Enter a 4-digit number to be registered
as PIN using the buttons numbered [1] -
[4] of the Preset buttons (2).
5) Hold down the TUNE FOLDER PUSH
SOUND knob (4) for 1 second or longer
to set the anti-theft function.NOTE:
Take a note of the registered PIN and keep
it for the future use. & D Q F H O L Q J W K H D Q W L W K H I W I H D W X U H
To cancel the anti-theft function, delete the
registered PIN.
1) Press the VOL PUSH POWER knob
(1) to power off.
2) Hold down the buttons numbered [1]
and [6] of the Preset buttons (2) and
press the VOL PUSH POWER knob
(1).
“PIN ENTRY” will be displayed.
3) Press the Up button (3) and the button
numbered [1] of the Preset buttons (2)
simultaneously.
4) Enter a 4-digit number to be registered
as PIN using the buttons numbered [1] -
[4] of the Preset buttons (2).
5) Hold down the TUNE FOLDER PUSH
SOUND knob (4) for 1 second or lon-
ger to delete the registered PIN. The
indication “----” will be displayed and
the anti-theft function will be canceled.
NOTE:
To change your PIN, first delete your cur-
rent PIN, then set a new one. & R Q I L U P L Q J W K H 3 H U V R Q D O , G H Q W L I L F D W L R Q
1 X P E H U 3 , 1
When the main power source is discon-
nected such as when the battery is
replaced, etc, it is required to enter the PIN
to make the unit operable again.
1) Set the ignition switch to the “ACC”
position.
“SECURITY” will be displayed.
2) Press the Up button (3) and the button
numbered [1] of the Preset buttons (2)
simultaneously.
3) Enter a 4-digit number to be registered
as PIN using the buttons numbered [1] -
[4] of the Preset buttons (2).
4) Hold down TUNE FOLDER PUSH
SOUND knob (4) for 1 second or lon-
ger.
When the PIN same as registered is
entered, the power of the audio system
will be turned off automatically and it
will become operable again.
NOTE:
If an incorrect PIN is entered, “ERROR”
and the total number of incorrect entry
attempts will be displayed.
If an incorrect PIN is entered 10 times or
more, “HELP” will be displayed and the
audio system will become inoperable.
Page 209 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
% D W W H U \ , Q V W D O O D W L R QInstall a lithium battery (CR2025) with the poles facing the correct direction.
% D W W H U \ U H S O D F H P H Q W W L P L Q J
• When battery power is depleted, the button may not be operable. If the remote controller
does not operate, replace the battery and check the operation.
& D X W L R Q R Q E D W W H U \
• Be sure to follow the instructions to prevent battery leakage, over-heating, ignition or
explosion.
If battery leakage has occurred, wipe the
container first then install a new battery. If
the battery solution contacts the skin, wash
off with water completely.
& D X W L R Q R Q 5 H P R W H & R Q W U R O O H U• Do not leave the remote controller in an
area exposed to direct sunlight, such as
on the dashboard or steering wheel. The
remote controller may deform because of
the heat, (Be especially careful of the
dashboard exposed to direct sunlight in
the summer, as it will become extremely
hot).
: $ 5 1 , 1 *
Page 244 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
) X V H V L Q W K H ( Q J L Q H & R P S D U W P H Q W
61MM0B068
64MS177
The main fuse, primary fuses and some of the
individual fuses are located in the engine
compartment. If the main fuse blows, no elec-
trical component will function. If a primary fuse
blows, no electrical component in the corre-
sponding load group will function. When
replacing the main fuse, a primary fuse or an
individual fuse, use a 0 D U X W L * H Q X L Q H 3 D U W To
remove a fuse, use the fuse puller provided in
the fuse box. The amperage of each fuse is
shown in the back of the fuse box cover.
(6)
(7) (1)
(2)
(3)
(4)
(5)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)(18)
(19)
(20)
(21)
(22)
(23)(24)
(25)
(26)
(27)
(28)(29)
(30)
(31)
(32)
(33)
(34)
(35)
0 $ , 1 ) 8 6 ( 3 5 , 0 $ 5 < ) 8 6 (
(1) 60 A FL7
(2) 80 A FL6
(3)
100 A
FL5
(4)
80 A
FL4
(5)
100 A
FL3
(6)
100 A
FL2
(7)
120 A
FL1
(8) 7.5 AIgnition-1 signal 2 (D16AA)
(9) 30 A Radiator fan 2
(10) 20 A Front fog light
(11) 7.5 A Headlight 2
(12) 25 A ABS control module
(13) 25 A Headlight
(14) 30 A Back up
(15) 40 A Ignition switch
(16) 40 A ABS motor
(17) 30 A Starting motor
(18) 30 A Radiator fan
(19) 30 A FI main
(20) 20 A Fuel pump
(21) 10 A Air compressor
(22) 7.5 A ECM (D13A)
(23) 30 A Blower fan
(24) 10 A FI 2 (D13A)
(25) 20 A INJ DRV (D13A)
(26) 7.5 A Starting signal
(27) 15 A Headlight (Left)
(28) 15 A Headlight high (Left)
(29) 7.5 A FI 2 (D16AA)
(30) 20 A INJ DRV (D16AA)
(31) 15 A FI 3 (D16AA)
(32) 15 A Headlight (Right)
(33) 15 A Headlight high (Right)
(34) 50 A Ignition switch 2
(35) 50 A Battery
Page 246 of 288
Downloaded from www.Manualslib.com manuals search engine 7-23INSPECTION AND MAINTENANCE
64MS0-74E
*Feature not available in the vehicle.
81A283
PRIMARY FUSE
(1) – Blank
(2) 20 A Power window timer
(3) 15 A Steering lock
(4) 20 A Rear defogger(5)
20 A
Sunroof*
(6)
10 A
DRL*
(7)
10 A
Heated mirror*
(8) 7.5 A Starting signal
(9) 15 A Accessory socket 2
(10) 30 A Power window
(11) 10 A Hazard
(12) 7.5 A BCM
(13) 15 A Ignition coil
(14) 10 A ABS control module
(15) 15 A Accessory socket
(16)
10 A
A-STOP controller*
(17) 15 A Horn
(18) 10 A Stop light
(19) 10 A Air bag
(20) 10 A Back-up light
(21) 15 A Wiper / Washer
(22) 30 A Front wiper
(23) 10 A Dome light(24)
15 A
4WD*
(25)
7.5 A
RR fog lamp*
(26) – Blank
(27) 7.5 A Ignition-1 signal
(28) 15 A Radio 2
(29) 10 A Accessory socket 3
(30) 15 A Radio
(31) 10 A Tail lamp
(32) 20 A D/L
(33) 7.5 A Cruise control
(34) 10 A Meter
(35) 7.5 A Ignition-2 signal
(36)
20 A
Seat heater*
WA R N I N G
Always be sure to replace a blown
fuse with a fuse of the correct amper-
age. Never use a substitute such as
aluminum foil or wire to replace a
blown fuse. If you replace a fuse and
the new one blows in a short period of
time, you may have a major electrical
problem. Have your vehicle inspected
immediately by your D X W K R U L V H G
0 D U X W L 6 X ] X N L Z R U N V K R S.
BLOWN OK
Page 269 of 288
Downloaded from www.Manualslib.com manuals search engine
( 0 ( 5 * ( 1 & < 6 ( 5 9 , & (
0 6 (
4) If the booster battery you are using is fit-
ted to another vehicle, start the engine of
the vehicle with the booster battery. Run
the engine at moderate speed.5) Start the engine of the vehicle with the
flat battery.
6) Remove the jump leads in the exact
reverse order in which you connected
them.
7 R Z L Q JIf you need to have your vehicle towed,
contact a professional service. Your dealer
can provide you with detailed towing
instructions.
: K H H O ' U L Y H : ' 0 D Q X D O 7 U D Q
V D [ O HManual transaxle vehicles may be towed
using either of the following methods.
1) From the front, with the front wheels
lifted and the rear wheels on the ground.
Before towing, make sure that the park-
ing brake is released.
2) From the rear, with the rear wheels lifted
and the front wheels on the ground, pro-
vided the steering and drivetrain are in
operational condition. Before towing,
make sure that transaxle is in neutral,
the steering wheel is unlocked (vehicle
without keyless push start system - the
ignition key should be in the “ACC” posi-
tion) (vehicle with keyless push start sys-
tem - the ignition mode is ACC), and the
steering wheel is secured with a clamp-
ing device designed for towing service.
& $ 8 7 , 2 1
& R Q Q H F W W K H M X P S O H D G W R W K H H Q J L Q H
P R X Q W E U D F N H W V H F X U H O \ , I W K H M X P S
O H D G G L V F R Q Q H F W V I U R P W K H H Q J L Q H
P R X Q W E U D F N H W E H F D X V H R I Y L E U D W L R Q D W
W K H V W D U W R I W K H H Q J L Q H W K H M X P S O H D G
F R X O G E H F D X J K W L Q W K H G U L Y H E H O W V
NOTICE
2 E V H U Y H W K H I R O O R Z L Q J L Q V W U X F W L R Q V
Z K H Q W R Z L Q J \ R X U Y H K L F O H
Page 270 of 288
Downloaded from www.Manualslib.com manuals search engine ( 0 ( 5 * ( 1 & < 6 ( 5 9 , & (
0 6 (
, I W K H 6 W D U W H U ' R H V 1 R W 2 S H U D W H1) Try turning the ignition switch to the
“START” position or try pressing the
engine switch to change the ignition
mode to START with the headlights
turned on to determine the battery condi-
tion. If the headlights go excessively dim
or go off, it usually means that either the
battery is flat or the battery terminal con-
tact is poor. Recharge the battery or cor-
rect battery terminal contact as
necessary.
, I W K H ( Q J L Q H L V ) O R R G H GIf the engine is flooded with the fuel, it may
be hard to start. If this happens, press the
accelerator pedal all the way to the floor
and hold it there while cranking the engine.
• For petrol engine model, do not operate
the starter motor for more than 12 sec-
onds.
• For diesel engine model, do not operate
the starter motor for more than 30 sec-
onds.
, I W K H ( Q J L Q H 2 Y H U K H D W VThe engine could overheat temporarily
under severe driving conditions. If the high
engine coolant temperature warning light
comes on as overheating during driving:
1) Turn off the air conditioner, if equipped.
2) Take the vehicle to a safe place and
park.
3) Let the engine run at the normal idle
speed for a few minutes until the high
engine coolant temperature warning
light goes off.
: $ 5 1 , 1 *
, I \ R X V H H R U K H D U H V F D S L Q J V W H D P
V W R S W K H Y H K L F O H L Q D V D I H S O D F H D Q G
L P P H G L D W H O \ W X U Q R I I W K H H Q J L Q H W R O H W
L W F R R O ' R Q R W R S H Q W K H K R R G Z K H Q
V W H D P L V S U H V H Q W : K H Q W K H V W H D P
F D Q Q R O R Q J H U E H V H H Q R U K H D U G R S H Q
W K H K R R G W R V H H L I W K H F R R O D Q W L V V W L O O
E R L O L Q J , I L W L V \ R X P X V W Z D L W X Q W L O L W
V W R S V E R L O L Q J E H I R U H \ R X S U R F H H G