2015 SUZUKI NEXA remote control
[x] Cancel search: remote controlPage 29 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
57L21016
To stow the key into the remote controller,
push the key in the remote controller until
you hear a click.
68LM247
To remove the key from the remote control-
ler, push the button (A) in the direction of
the arrow and pull the key out from the
remote controller. 5 H T X H V W V Z L W F K Z D U Q L Q J E X ] ] H U
This exterior buzzer beeps for about 2 sec-
onds in the following conditions to warn you
that the request switch is not working:
• The request switch is pressed after all
doors are closed with the ignition mode
changed to “ACC” or “ON” by pressing
the engine switch.
• The request switch is pressed in any of
the following conditions after changing
the ignition mode to “LOCK” (OFF) by
pressing the engine switch.
– The remote controller is left inside the
vehicle.
– Any door (including the tailgate) is
open.
Press the request switch again after doing
the following:
With the ignition mode changed to “LOCK”
(OFF) by pressing the engine switch, bring
out the remote controller if it is inside the
vehicle and check that all doors are com-
pletely closed.
5 H P L Q G H U I X Q F W L R Q
64MS165
If the remote controller is not in the vehicle
under the following conditions, the buzzer
sounds intermittently for about 2 seconds
and the immobilizer/keyless push start sys-
tem warning light on the instrument cluster
blinks:When one or more doors are opened and
all of the doors are later closed with the
ignition mode is other than “LOCK”.
The indicator light will turn off within sev-
eral seconds after the remote controller is
returned to an area of the vehicle other
than the rear luggage area.
If the remote controller is left in the vehicle
and you lock the driver’s door or front pas-
senger’s door as described below, the door
will be automatically unlocked.
• If you open the driver’s door and lock the
door by turning the lock knob forward or
pushing the power door locking switch,
(A)
( ; $ 0 3 / (
Page 30 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
the driver’s door will be automatically
unlocked.
• If you open the front passenger’s door
and lock the door by turning the lock
knob forward or pushing the power door
locking switch, the front passenger’s
door will be automatically unlocked.
NOTE:
• The reminder will not operate when the
remote controller is on the instrument
panel, in the glove box, in a storage
compartment, in the sun visor or on the
floor etc.
• Be sure that the driver always carries the
remote controller.
• Do not leave the remote controller in the
vehicle when leaving the vehicle. 5 H S O D F H P H Q W R I W K H E D W W H U \
If the remote controller becomes unreli-
able, replace the battery.
To replace the battery of the remote con-
troller:
71LMT0201
1) Pull the key out from the remote con-
troller.
2) Insert a flat blade screwdriver covered
with a soft cloth in the slot of the remote
controller and pry it open.
68LM210
(1) Lithium disc type battery:
CR2032 or equivalent
3) Replace the battery (1) so its + terminal
faces the bottom of the case as shown
in the illustration.
4) Close the remote controller firmly.
5) Make sure the door locks can be oper-
ated with the remote controller.
6) Dispose of the used battery properly
according to applicable rules or regula-
tions. Do not dispose of lithium batter-
ies with ordinary household trash.
NOTICE
: K H Q U H S O D F L Q J W K H E D W W H U \ G R Q R W
W R X F K W K H H O H F W U R Q L F F R P S R Q H Q W L Q W K H
U H P R W H F R Q W U R O O H U Z L W K Z H W R U R L O
V W D L Q H G K D Q G V 2 W K H U Z L V H W K H U H P R W H
F R Q W U R O O H U P D \ E H G D P D J H G
: $ 5 1 , 1 *
6 Z D O O R Z L Q J D O L W K L X P E D W W H U \ P D \
F D X V H V H U L R X V L Q W H U Q D O L Q M X U \ ' R Q R W
D O O R Z D Q \ R Q H W R V Z D O O R Z D O L W K L X P
E D W W H U \ . H H S O L W K L X P E D W W H U L H V D Z D \
I U R P F K L O G U H Q D Q G S H W V , I V Z D O O R Z H G
F R Q W D F W D S K \ V L F L D Q L P P H G L D W H O \
(1)
Page 34 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
6 H F X U L W \ 6 \ V W H P L I H T X L S S H G The security system is armed in about 5
seconds after you lock all doors (including
the tailgate) by using the keyless entry sys-
tem transmitter, keyless push start system
remote controller or request switch.
Once the system is armed, any attempt to
open a door by using any other means (*)
than the keyless entry system transmitter,
keyless push start system remote control-
ler or request switch, or open the engine
hood, will cause the alarm to be triggered.
* These means include the following:
– The key
– The lock knob on a door
– The central door locking switchAlso, in case that you have set the shock
sensor to enabled state and set sensitivity
of the pre-warning function and full blast
warning function to a level other than 0, the
alarm will be triggered if any attempt is
made to tamper with the vehicle. The shock
sensor can be selected to enabled or dis-
abled state, and sensitivity of each warning
can be adjusted as desired. To set the
shock sensor, ask your D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S or use the setting mode of
the information display.NOTE:
• The default setting of the shock sensor
is in the disabled state. Set to the
enabled state and adjust sensitivity of
each warning according to your prefer-
ence. For details on how to use the infor-mation display, refer to “Information
Display” in this section.
• Your dealer may have already set the
shock sensor of the vehicle to the
enabled state before you purchase it.
Consult your dealer for further informa-
tion.
NOTE:
• The security system generates alarms
when any of the predetermined condi-
tions is met. However, the system does
not have any function of blocking unau-
thorized entry into the vehicle.
• Always use the keyless entry system
transmitter, keyless push start system
remote controller or request switch to
unlock the doors when the security sys-
tem has been armed. Using a key
instead will trigger the alarm.
• If a person who does not know the secu-
rity system is going to drive the vehicle,
we recommend you explain the system
and its operation to the person, or dis-
able the system beforehand. Mistakenly
triggering the alarm may cause a nui-
sance to others.
• Even if the security system is armed,
you should still be careful to guard
against theft. Do not leave money or
things of value in the vehicle. + R Z W R D U P W K H V H F X U L W \ V \ V W H P
Z K H Q H Q D E O H G
Lock all doors (including the tailgate) using
the keyless entry system transmitter, key-
less push start system remote controller or
request switch. The security system indica-
tor (1) will start blinking rapidly, and the
security system will be armed in about 5
seconds.
While the system is being armed, the indi-
cator continues to blink at intervals of
approximately 2 seconds
61MM0A134
NOTE:
• To prevent the alarm from being acci-
dentally triggered, avoid arming it while
anyone remains inside the vehicle. The
alarm will be triggered if any person
inside opens the door or engine hood, or
swings the vehicle (if the shock sensor is
in the enabled state).
• The security system is not armed when
all doors are locked using the key from
(1)
Page 35 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
outside, or using the door lock knobs or
the central door locking switch from
inside.
• If any door is not operated within approx-
imately 30 seconds after the doors have
been unlocked using the keyless entry
system transmitter, keyless push start
system remote controller or request
switch, the doors are automatically
locked again. When the doors are
locked, the security system will be
armed in about 5 seconds if the system
is in the enabled state.
• If the security system indicator (1) blinks
when the ignition switch is in the “ON”
position or the ignition mode is “ON”,
there may be something wrong with the
security system. Ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S to
inspect the system.
+ R Z W R G L V D U P W K H V H F X U L W \ V \ V W H P
Simply unlock the doors using the keyless
entry system transmitter, keyless push
start system remote controller or request
switch. The security system indicator will
go out, indicating that the security system
is disarmed.
+ R Z W R V W R S W K H D O D U P
Should the alarm be triggered accidentally,
unlock the doors using the keyless entry
system transmitter, keyless push start sys-
tem remote controller or request switch, or
insert the key in the ignition switch and turn
it to “ON” position, or press the engineswitch to change the ignition mode to
“ON”. The alarm will then stop.
NOTE:
• Even after the alarm has stopped, if you
lock the doors using the keyless entry
system transmitter, keyless push start
system remote controller or request
switch, the security system will be
rearmed with a delay of about 5 sec-
onds.
• If you disconnect the battery while the
security system is in the armed condition
or the alarm is actually in operation, the
alarm will be re-triggered when the bat-
tery is then reconnected.
• Even after the alarm has stopped at the
end of the predetermined operation time,
it will be triggered again if any of the
doors or engine hood is opened, or the
vehicle feels a shock (if the shock sen-
sor is in the enabled state), without dis-
arming the security system.
& K H F N L Q J Z K H W K H U W K H D O D U P K D V E H H Q
W U L J J H U H G G X U L Q J S D U N L Q J
If the alarm was triggered and you then
turn the ignition switch to “ON” position, or
press the engine switch to change the igni-
tion mode to “ON”, the security system
indicator will blink rapidly for about 8 sec-
onds and a buzzer will beep 4 times during
this period. If this happens, check whether
the vehicle has been broken into while you
were away from it. ( Q D E O L Q J D Q G G L V D E O L Q J W K H V H F X U L W \
V \ V W H P
The security system can be either enabled
or disabled.
: K H Q H Q D E O H G
• If any of the doors are opened without
unlocking by the keyless entry system
transmitter, keyless push start system
remote controller or request switch, all
turn signal lights start to blink and the
interior buzzer beeps intermittently. After
5 seconds, the siren will sound for about
27.5 seconds. The security system indi-
cator continues to blink during this time.
• If the engine hood is opened, all turn sig-
nal lights blink, and the siren sounds for
about 27.5 seconds. The security sys-
tem indicator continues to blink during
this time.
( , I W K H V K R F N V H Q V R U L V L Q W K H H Q D E O H G
V W D W H
• If the vehicle feels a shock, the siren
sounds for about 2 seconds (pre-warn-
ing). If the vehicle continues to feel a
shock, all turn signal lights start to blink
and the interior buzzer beeps intermit-
tently. After 5 seconds, the siren will
sound for about 27.5 seconds (full blast
warning). The security system indicator
continues to blink during this time.
NOTE:
If you set the full blast warning sensitivity
higher than the pre-warning sensitivity in
the setting mode of the information display,
or the vehicle feels such shock as to be
Page 76 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
: D U Q L Q J D Q G , Q G L F D W R U
0 H V V D J H 0 D V W H U : D U Q L Q J
, Q G L F D W R U / L J K W 6 R X Q G & D X V H D Q G 5 H P H G \
Keyless Push Start System
61MM0A170
Blinks Series of beeps under cer-
tain conditions (for about 2
seconds from exterior and/or
interior buzzers)The remote controller may be outside the
vehicle or its battery may have become dis-
charged. Locate the remote controller or
touch the engine switch with the remote
controller.
If the message still appears, replace the
remote controller battery.
61MM0A171
Page 78 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
(#1) This message will disappear for a while even if the problem that caused the message to appear is not corrected. : D U Q L Q J D Q G , Q G L F D W R U
0 H V V D J H 0 D V W H U : D U Q L Q J
, Q G L F D W R U / L J K W 6 R X Q G & D X V H D Q G 5 H P H G \
61MM0A176
Off Off The road may be icy. Drive very carefully.
(#1)
Keyless Push Start System
61MM0A177
Off Off The remote controller battery is about to
become flat. Replace the battery. (#1)
61MM0A225
Blinks Beep (one time from interior
buzzer) There may be a problem with the fuel filter.
Have your vehicle inspected by an autho-
rized M D U X W L 6 X ] X N L Z R U N V K R S.
Page 105 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
NOTE:
In the presence of strong radio signals or
noise, you may not be able to change the
ignition mode to ACC or ON or to start the
engine using the engine switch. In this
case, the information display on the instru-
ment cluster will show the following mes-
sage: KEY FOB NOT DETECTED. 8 Q U H O H D V H G 6 W H H U L Q J / R F N : D U Q L Q JIf the steering lock remains engaged when
you press the engine switch to change the
ignition mode to “ON”, the information dis-
play in the instrument cluster shows the
message: “TRN. STEERING WHEEL TO
RELEASE LOCK”. Refer to “Information
Display” in the ³ % ( ) 2 5 ( ' 5 , 9 , 1 * ´ sec-
tion for details.
NOTE:
The steering lock may not be released if
some load is acting on the steering wheel.
If this happens, turn the steering wheel to
the right or left to relieve it from the load
before you press the engine switch again
to change to the desired ignition mode.
. H \ O H V V 3 X V K 6 W D U W 6 \ V W H P
L I H T X L S S H G Provided the keyless push start system
remote controller is within the “interior
workable area” (refer to the related expla-
nation in this section), you can use the
engine switch for starting the engine and
selecting an ignition mode (ACC or ON). In
addition, the following functions can be
used:
• Keyless entry function. Refer to “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section for
details.
• Locking and unlocking doors (including
the tailgate) using a request switch.
Refer to “Keyless Push Start System
Remote Controller” in the “BEFORE
DRIVING” section for details.
• Immobilizer (anti-theft) function. Refer to
“Immobilizer System” in the “BEFORE
DRIVING” section for details. ( Q J L Q H 6 Z L W F K , O O X P L Q D W L R QThe engine switch is illuminated (lit) in the
following situations:
• When the engine is off and the driver’s
door is open or for 15 seconds after the
drivers door is closed.
• When the engine is off and the position
lights are on. The illumination will go out
when the position lights are turned off.
• When the engine is on and the position
lights and/or the headlights are on. Theillumination will go out when the head-
lights are turned off.
82K253
NOTE:
To save the battery, the illumination will be
automatically turned off when both of the
following conditions are simultaneously
met:
• The headlights and position lights are
turned off.
• A period of 15 minutes has elapsed after
opening the driver’s door. 6 H O H F W L R Q R I , J Q L W L R Q 0 R G H VPress the engine switch to select the
“ACC” or “ON” mode as follows when you
use an electric accessory or check the
operation of instruments without running
the engine.
1) Bring the keyless push start system
remote controller with you and sit in the
driver’s seat.
Page 106 of 288
Downloaded from www.Manualslib.com manuals search engine (1)
(2)
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
2) Without depressing the clutch pedal,
press the engine switch (1).
82K254
Every time you press the engine switch,
the ignition mode changes as follows.
57L31033
NOTE:
When selecting the ignition modes, the
information display in the instrument clus-
ter shows certain messages. Refer to
“Information Display” in the “BEFORE
DRIVING” section for details. , I W K H 0 $ 6 7 ( 5 : $ 5 1 , 1 * L Q G L F D W R U O L J K W
E O L Q N V D Q G W K H L J Q L W L R Q P R G H V F D Q Q R W
E H V H O H F W H G
Your keyless push start system remote con-
troller may not be sensed as being within the
“interior workable area” (refer to the related
explanation in this section). Try again after
making sure you have the remote controller
with you. If the ignition modes still cannot be
selected, the battery of the remote controller
may be discharged. To be able to select an
ignition mode, you must then use the follow-
ing method:
58MST0302
1) Without depressing the brake pedal
and the clutch pedal, push the engine
switch (1).
2) Within about 10 seconds during which
the master warning indicator light in the
instrument cluster is blinking and the
“PLACE KEY FOB ON START
SWITCH” message appears on the
information display, touch the engineswitch with the lock button end of the
remote controller (2) for about 2 sec-
onds.
NOTE:
•
If you still cannot select the ignition
modes, there may be some problem with
the keyless push start system. Contact
an D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
for an inspection of the system.
• The immobilizer/keyless push start sys-
tem warning light will come on for about
5 seconds while the master warning indi-
cator light is blinking. In addition, the
information display in the instrument
cluster will show a message during this
time. Refer to “Information Display” in
the “BEFORE DRIVING” section for
details.
•
You may customize the system to cause
the interior buzzer to sound once for the
remote controller out of sensing range
warning. To incorporate this customiza-
tion, please contact an D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S
• If the battery of the remote controller is
about to become completely discharged,
the corresponding message will appear
on the information display when you
press the engine switch to change the
ignition mode to ON. Refer to “Informa-
tion Display” in the “BEFORE DRIVING”
section for details. For details on replac-
ing the battery, refer to the “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section.
(OFF)
ON ACC LOCK
(Audio equipment)
( ; $ 0 3 / (
(1)