2015 Peugeot Partner Tepee Owner's Manual

55
Partner_2_VP_en_Chap04_ergonomie_ed02-2014
2 Fast wipe (heavy rain).
1
Normal wipe (moderate rain).
l


Intermittent wipe.
0


Of
f.
â Single wipe
(press downwards).
In the

Intermittent position, the wiping
speed is in proportion to the vehicle
speed.
WINDSCREEN WIPER STALK
Manual windscreen wipers
Whenever the ignition has been
switched off for more than one minute,
with the windscreen wiper stalk in
position 2, 1 or I, the stalk must be
reactivated:
-

move the stalk to any position,
-


then move it back to the required
position. Do not cover the rain sensor

,
located in the centre of the
windscreen, behind the mirror. Activation
Press the control downwards.
Activation of the function is
accompanied by a message in
the
screen.
Deactivation / Switching off
Place the windscreen wipers stalk in
position I, 1 or 2. Deactivation of the
function is accompanied by a message
in the screen.
In the event of malfunction of the
automatic windscreen wipers, the
windscreen wipers will operate in
intermittent mode.
Contact a P euge O t
dealer or a
qualified workshop to have the system
checked. In the
AUTO position, the windscreen
wipers operate automatically and
adapt their speed to the intensity of
the rainfall.
When not in AUTO mode, for the
other positions, refer to the manual
windscreen wipers section.
t
he automatic rain sensitive
windscreen wipers function must
be reactivated by pressing the stalk
downwards, if the ignition has been
switched off for more than one minute.
When using an automatic car
wash, switch off the ignition to
avoid triggering the automatic
wiping.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating automatic wipe.
Automatic rain sensitive windscreen wipers
Steering mounted controls
eASe OF uSe and COMFORt
4

56
Partner_2_VP_en_Chap04_ergonomie_ed02-2014
Screenwash and headlamp wash
Pull the stalk towards you, the wash-
wipe is accompanied by a timed sweep
of the wipers.
t
he headlamp wash is linked with the
wash-wipe, it is triggered if the dipped
headlamps are on.
Turn the ring past the first
position: the rear screenwash
then the rear wiper operates
for a fixed time.
In winter, in the event of a
considerable amount of snow
or ice, switch on the heated
rear screen. Once the screen is
clear, remove the snow or ice which
has accumulated on the rear wiper
blade. You can then operate the rear
windscreen wiper.
to top up the levels, refer to the
"Levels" section of chapter 7.
Special position of the
windscreen wipers
In the minute following switching
off of the ignition, any action on the
stalk positions the wipers against the
windscreen uprights.
t

his action enables you to position
the wiper blades for winter parking,
cleaning or replacement.
Refer to the "Changing a
windscreen wiper blade" section
of chapter 8.
to park the wipers in their normal
position after this has been done,
switch on the ignition and move
the

stalk. Turn the ring to the first
position.
Rear wiper
Rear screenwash
Steering mounted controls

57
Partner_2_VP_en_Chap04_ergonomie_ed02-2014
CRUISE CONTROL "CRUISE"
In order for it to be programmed or
activated, the vehicle speed must be
greater than 25 mph (40 km/h) with at
least 4th gear engaged.
t
his cruise control shows the function
selection status in the instrument panel
and displays the programmed speed:
Function selected,
display of the "Cruise
Control" symbol.
Function deactivated,
OFF.
Function activated.
Vehicle speed above
the programmed
speed, which is
displayed flashing.
Operating fault
detected,
OFF - the dashes
flash.
"
t
his is the speed at which the driver
wishes to drive".
This aid to driving in free-flowing
traffic enables the vehicle to maintain
the speed programmed by the driver,
unless a steep gradient makes this
impossible.
Steering mounted controls
eASe OF uSe and COMFORt
4

58
Partner_2_VP_en_Chap04_ergonomie_ed02-2014
Selecting the function
- Place the switch in the CRUISE
position. t he cruise control is
selected but is not yet active and
no speed has been programmed.
First activation /
Programming a
speed Temporarily exceeding the
speed
It is possible to accelerate and drive
momentarily at a speed greater than
the programmed speed.
t

he value
programmed flashes.
When the accelerator pedal is
released, the vehicle will return to the
programmed speed.
Deactivation (off)
- Press this button or
the brake or clutch
pedal.
Reactivation
- Following deactivation of the cruise
control, press this button.
Y
our vehicle will return to the last
programmed speed.
Alternatively, you can repeat the "first
activation" procedure.
-

Reach the chosen speed by
pressing the accelerator

.
-

Press the

SET - or SET + button.
t

his programmes/activates the
reference speed and the vehicle will
maintain this speed.
Steering mounted controls

59
Partner_2_VP_en_Chap04_ergonomie_ed02-2014
Changing the
programmed
speedSwitching the function off
Operating fault
the programmed speed is cleared then
replaced by three dashes. Contact
a PEUGEOT
dealer or a qualified
workshop to have the system checked.
Cancelling the programmed
reference speed
When the vehicle becomes stationary,
after switching off the ignition, the
system no longer memorises a speed.
t

here are two methods of memorising
a speed higher than the previous one:
Without using the accelerator:
-
press the
SET + button.
A brief press increases the speed by
1 mph (km/h).
A maintained press increases the
speed in steps of 5 mph (km/h).
u

sing the accelerator:
-

exceed the memorised speed until
the speed required is reached,
-


press the

SET + or SET - button.
to memorise a speed lower than the
previous one:
-


press the

SET - button.
A brief press decreases the speed by
1 mph (km/h).
A maintained press decreases the
speed in steps of 5 mph (km/h). -

Place the dial in position
0 or
switch off the ignition to switch
everything off.
Good practice
When changing the programmed
reference speed by means of a
maintained press, pay attention as
the speed can increase or decrease
rapidly.
Do not use the cruise control on
slippery roads or in heavy traffic.
In the event of a steep slope, the cruise
control cannot prevent the vehicle from
exceeding the programmed speed.
In any event, the cruise control cannot
replace the need to observe the speed
limits and the need for vigilance on the
part of the driver.
It is advisable to leave your feet near
the pedals.
to avoid any jamming under the
pedals:
-


ensure that the mat and its fixings
on the floor are positioned correctly

,
-

never place one mat on top of
another

.
Steering mounted controls
eASe OF uSe and COMFORt
4

60
Partner_2_VP_en_Chap04_ergonomie_ed02-2014
However, pressing the pedal beyond
this point of resistance to the floor
allows the programmed speed to be
exceeded.
to resume use of the limiter
,
simply reduce the pressure on the
accelerator pedal gradually and return
to a speed below that programmed.
The operating actions may be
carried out when stationary, with the
engine running, or with the vehicle
moving.
t
his speed limiter shows the function
selection status in the instrument panel
and displays the programmed speed:
SPEED LIMITER "LIMIT"
Function selected,
displaying of the
"Speed Limiter"
symbol.
Function deactivated,
last programmed
speed - OFF.
Function activated.
Vehicle speed above
the programmed
speed, which is
displayed flashing.
Operating fault
detected,
OFF - the dashes
flash.
"
t
his is the selected speed which the
driver does not wish to exceed".
t

his selection is made with the engine
running while stationary or with the
vehicle moving.
t

he minimum speed
which can be programmed is 20 mph
(30 km/h).
t

he speed of the vehicle responds
to the pressure of the driver's foot as
far as the accelerator pedal point of
resistance which indicates that the
programmed speed has been reached.
Steering mounted controls

61
Partner_2_VP_en_Chap04_ergonomie_ed02-2014
Selecting the function
- Place the switch in the LIMIT
position. t he limiter is selected
but is not yet active.
t

he screen
indicates the last programmed
speed.
Programming a speed
A speed can be programmed without activating
the limiter but with the engine running.
to memorise a speed higher than the


previous
one:
- press the SET + button.
A brief press increases the speed
by
1 mph (km/h).
A maintained press increases the speed in
steps of 5 mph (km/h).
to memorise a speed lower than the previous


one:
- press the SET - button.
A brief press decreases the speed
by
1 mph (km/h).
A maintained press decreases the speed in
steps of 5 mph (km/h).
Activation / Deactivation
Pressing this button once activates
the limiter, pressing the button again
deactivates it (OFF).
Steering mounted controls
eASe OF uSe and COMFORt
4

62
Partner_2_VP_en_Chap04_ergonomie_ed02-2014
Exceeding the programmed
speed
Pressing the accelerator pedal in order
to exceed the programmed speed
will have no effect unless you press
the pedal firmly beyond the point of
resistance.
t
he limiter is deactivated temporarily
and the programmed speed flashes
accompanied by an audible signal.
to return to the limiter function, reduce
your speed to below the programmed
speed.
Switching the function off
- Place the switch in position 0 or
switch off the ignition to switch the
system off.
t

he last programmed speed remains in
the memory.
Operating fault
the programmed speed is cleared
then replaced by three dashes.
Contact a P
euge O t
dealer or a
qualified workshop to have the system
checked.
Good practice
Flashing of the speed
The speed flashes:
-

following forcing of the accelerator
point of resistance,
-


when the limiter cannot prevent an
increase in the vehicle speed due
to the profile of the road or on a
steep descent,
-


in the event of sharp acceleration. In any event, the speed limiter cannot
replace the need to observe speed
limits, nor can it replace the need for
vigilance on the part of the driver

.
Always pay attention to the profile
of the road and sharp acceleration
and stay in complete control of your
vehicle.
to avoid any jamming under the
pedals:
-


ensure that the mat and its fixings
on the floor are positioned correctly

,
-

never place one mat on top of
another

.
Steering mounted controls