2015 MITSUBISHI MIRAGE Owners Manual

Heater without air conditioning function (if so equipped) 7-4 Comfort controls
7
Air flows mainly to the windshield and the door windows.
N00737700031
The heater can only be used while the engineis running.
N00737800032
N00737900033
When the ignition switch is in the “ON” posi- tion, select the blower speed by turning the blower speed selection dial.Turning the dial clockwise will increase the blower speed; turning
the dial counterclock-
wise will decrease it. When the dial is set tothe “OFF” position, all fan-driven airflow will stop.
N00738000057
The temperature control lever is used to select the desired air temperature.
NOTE
 With the mode selec
tion dial between the
“ ” and “ ” positions, air flows mainly to the leg area. With the mode selection dial between the “ ”and “ ” positions, air flows mainly to the windshield and the door windows.
Defroster position
Heater without air condi- tioning function
(if so equipped)
Control panel

1- Temperature control lever 2- Air selection lever 3- Mode selection dial4- Electric rear win
dow defogger switch
 P. 5-80
5- Blower speed selection dial
Blower speed selection dial

Temperature control lever

BK0212400US.book 4 ページ ２０１４年４月１日　火曜日　午後２時２１分

Heater without air conditioning function (if so equipped)
Comfort controls 7-5
7
N00738100061
To change the amount of air flowing from the vents, turn the mode
selection dial. Refer to
“Changing the mode se
lection” on page 7-2.
N00738200046
Normally, use the outside air position to keep the windshield and side
windows clear and to
quickly remove fog or frost from the wind-shield. To change the air selection, use the air selec- tion lever.  “ ” Outside air  “ ” Recirculated air
If the outside air is dusty or contaminated in some way, use the
recirculat
ion position.
Switch to the outside air position every now and then to keep the windows from foggingup.
N00738300047
Set the mode selection
dial to the “ ” posi-
tion and set the air selection lever to the out- side air position.Set the temperature control lever to the desired temperature.
Select the desired
blower speed to fit your needs.
1- Cooler 2- WarmerMode selection dial

Air selection lever

CAUTION Using recirculated ai
r for a long time may
cause the windows to fog up.
Operating the system

Heating

BK0212400US.book 5 ページ ２０１４年４月１日　火曜日　午後２時２１分

Heater without air conditioning function (if so equipped) 7-6 Comfort controls
7
N00738400035
Set the mode selection dial to the positions shown in the illustrati
on and set the air selec-
tion lever to the out
side air position.
The air flow will be directed to the leg area and the upper part of the passenger compart- ment. Set the desired blower speed. Warm air flows to the leg area and unheatedor slightly warm air (depending upon the position of the temper
ature control lever)
flows to the upper part of the passenger com-partment.
N00738500081
Set the mode selection dial (between “ ” and “ ”) to remove frost or mist from the windshield and door window. Use this setting to ke
ep the windshield and
door windows clear of mist, and to keep the leg area heated (when driving in rain or snow). 1. Set the mode selection dial to the “ ” position.
2. Set the air selection lever to the outside air position.3. Select your desired blower speed by turn- ing the blower speed selection dial. 4. Select your desired temperature by settingthe temperature control lever.
For quick defrosting 1. Set the mode selection dial to the “ ” position. 2. Set the air selection lever to the outside airposition. 3. Set your blower to the maximum speed. 4. Set the temperature to the highest posi-tion.
NOTE
 For quick heating, set the blower speed at the 3rd position.
Combination of unheated air and heated air

Defrosting or defogging (wind- shield, door windows)

CAUTION For safety, make sure
you have a clear view
through all the windows.
For ordinary defrosting
NOTE
 To defog quickly, direct the air flow from the side vents toward the door windows.
BK0212400US.book 6 ページ ２０１４年４月１日　火曜日　午後２時２１分

Manual air conditioning (if so equipped)
Comfort controls 7-7
7
N00730300344
The air conditioning ca
n only be used while
the engine is running.
N00730500304
N00736500205
When the ignition switch or the operation mode is in ON, select
the blower speed by
turning the blower sp
eed selection dial.
Turning the dial clockw
ise will increase the
blower speed; turning
the dial counterclock-
wise will decrease it. When the dial is set tothe “OFF” position, all fan-driven airflow will stop.
N00736600248
The temperature control lever is used to select the desired air temperature.
N00736700223
To change the amount of air flowing from thevents, turn the mode
selection dial. Refer to
“Changing the mode se
lection” on page 7-2.
Manual air conditioning
(if so
equipped)Control panel

1- Temperature control lever 2- Air selection lever 3- Mode selection dial 4- Electric rear
window defogger
switch
 P. 5 - 8 0
5- Air conditioning switch 6- Blower speed selection dial
Blower speed selection dial

Temperature control lever

1- Cooler2- Warmer
NOTE
 While the engine coolant temperature is low, the temperature of the air from the heaterwill be cool/cold unti
l the engine warms up,
even if you have selected warm air with the lever.
Mode selection dial

BK0212400US.book 7 ページ ２０１４年４月１日　火曜日　午後２時２１分

Manual air conditioning (if so equipped) 7-8 Comfort controls
7
N00736800413
Normally, use the outside air position to keep the windshield and side windows clear and to quickly remove fog or frost from the wind- shield. To change the air selection, use the air selec- tion lever.  “ ” Outside air  “ ” Recirculated air
If the outside air is dusty or contaminated in some way, use the recirculation position.Switch to the outside
air position every now
and then to keep the windows from fogging up.
N00731000478
Push the switch, and the air conditioningcompressor will turn on. The air conditioning indicator light (A) will come on.
Push the switch again and the air condition- ing compressor will stop and the indicatorlight (A) goes off.
N00731100264
Set the mode selection dial to the “ ” posi-tion and set the air sele
ction lever to the out-
side air position.
Air selection lever

CAUTION Using recirculated ai
r for a long time may
cause the windows to fog up.
Air conditioning switch

CAUTION Using the air conditioni
ng slightly increases
the engine idle
speed. Therefore, make sure
your foot is firmly on the brake pedal when shifting the transaxle into drive.
Operating the air conditioning system

Heating

BK0212400US.book 8 ページ ２０１４年４月１日　火曜日　午後２時２１分

Manual air conditioning (if so equipped)
Comfort controls 7-9
7
Set the temperature control lever to the desired temperature.
Select the desired
blower speed to fit your needs.
N00731200340
1. Set the mode selection dial to the “ ”position. 2. Set the air selection lever to the outside air position.3. Push the air conditioning switch. 4. Change the temperature by setting the temperature control lever.5. Set the desired blower speed.
N00731300282
Set the mode selection
dial to the positions
shown in the illustration and set the air selec- tion lever to the outside air position. The air flow will be directed to the leg area and the upper part of
the passenger compart-
ment. Set the desired blower speed. Warm air flows to the leg area and unheated or slightly warm
air (depending upon the
position of the temperature control lever) flows to the upper part of the passenger com-partment.
NOTE
 For quick heating, set th
e blower speed at the
3rd position.
Cooling

NOTE
 If the outside air is dusty or contaminated in some way, set the air selection lever to the recirculation position.
Let in some outside
air from time to time for good ventilation.  To cool the leg areas, set the mode selection dial to the “ ” position.
Combination of unheated air and heated air

BK0212400US.book 9 ページ ２０１４年４月１日　火曜日　午後２時２１分

Manual air conditioning (if so equipped) 7-10 Comfort controls
7
N00731400560
Set the mode selection dial (between “ ” and “ ”) to remove frost or mist from the windshield and door window. Use this setting to ke
ep the windshield and
door windows clear of mist, and to keep the leg area heated (when driving in rain or snow). 1. Set the mode select
ion dial to the “ ”
position.
2. Set the air selection le
ver to the outside air
position.3. Select your desired
blower speed by turn-
ing the blower spee
d selection dial.
4. Select your
desired temperature by setting
the temperature control lever. 5. Push the air conditioning switch. For quick defrosting 1. Set the mode selection dial to the “ ” position.2. Set the air selection le
ver to the outside air
position. 3. Set your blower to the maximum speed.4. Set the temperature to the highest posi- tion. 5. Push the air conditioning switch.
Defrosting or defogging (wind- shield, door windows)

CAUTION For safety, make sure you have a clear view through all the windows.
For ordinary defrosting
NOTE
 To defog quickly, direct the air flow from the side vents toward the door windows.
 When defrosting, do not set the temperature control dial near the
maximum cool position.
This would blow cool air on the windowglass and fog it up.NOTE
BK0212400US.book 10 ページ ２０１４年４月１日　火曜日　午後２時２１分

Automatic air conditioning (if so equipped)
Comfort controls 7-11
7
N00731500301
The air conditioning can only be used
while the engine is running.
N00711801624
Automatic air conditioning
(if so equipped)
Control panel

Ty p e 1 Ty p e 2
1- Temperature control switch 2- Air conditioning switch 3- MODE switch4- Air selection switch 5- Blower speed
selection switch
6- Defogger switch7- AUTO switch 8- Electric rear window defogger switch
 P.5-80
9- OFF switch 10- Temperature display 11- Mode selection display 12- Air selection indicator13- Air conditioning indicator 14- AUTO indicator 15- Blower speed display
NOTE
 There is an interior air temperature sensor (A) in the illustrated position. Never place anything ove
r the sensor, since
doing so will prevent
it from functioning
properly.
BK0212400US.book 11 ページ ２０１４年４月１日　火曜日　午後２時２１分