2015 MITSUBISHI L200 set clock

CAUTIONlNormally, use the “” (outside) position
to keep the windscreen and side windows clear and quickly remove fog or frost from
the windscreen.
If high cooling performance is desired, or if
the outside air is dusty or otherwise contami-
nated, use the “
” (recirculation) position.
Set the air selection lever to the “
” (out-
side) position periodically to increase venti-
lation so that the windows do not become fogged up.
l Use of the “
” (recirculation) position for
extended time may cause the windows to fog up.
Air conditioning switch*
E00701500781
Push the switch, and the air conditioning
compressor will turn on. The air conditioning
indication lamp (A) will come on.
Push the switch again and the air condition-
ing compressor will stop and the indication
lamp goes off.
CAUTIONl When using the air conditioning, the idling
speed may slightly increase as the air condi- tioning compressor is switched on/off auto-
matically. While the vehicle with an A/T is
stationary, fully depress the brake pedal to
prevent the vehicle from creeping.Operating the air conditioning
system
E00701800247
Heating
Set the mode selection dial to the “” posi-
tion and set the air selection lever to the
“
” (outside) position.
Turn the temperature control dial clockwise
or anticlockwise to the desired temperature. Select the desired blower speed.NOTEl For maximum heat, set the blower speed at
the 3 rd
position.
Heater/Manual air conditioning*
7-06OKTE15E3For pleasant driving7 LHD RHD LHD RHD

Cooling (vehicles with air condi-tioning)
E00701900424
1. Set the mode selection dial to the “”
position.
2. Set the air selection lever to the “
”
(outside) position.
3. Push the air conditioning switch (B).
4. Change the temperature by turning the
control dial clockwise or anticlockwise.
5. Select the desired blower speed.CAUTIONl If the outside air is dusty or otherwise conta-
minated, or if high cooling performance is
desired, set air selection lever to the “
”
(recirculation) position and the temperature control dial all the way to the left.
Set to the “
” (outside) position periodi-
cally to increase ventilation so that the win- dows do not become fogged up.
Combination of unheated air
and heated air
E00702000451
Select the mode selection dial to the position shown in the illustration and set the air selec- tion lever to the “
” (outside) position.
The air flow will be directed to the leg area
and the upper part of the passenger compart-
ment. Select the desired blower speed.
Warm air flows to the leg area and unheated
or slightly warm air (depending upon temper-
ature setting) flows to the upper part of the
passenger compartment.
Demisting of the windscreen
and door windows
E00702100579
CAUTIONl For safety, make sure you have a clear view
through all the windows.
To remove frost or mist from the windscreen
and door windows, use the mode selection di-
al (“
” or “”).
Heater/Manual air conditioning*
7-07OKTE15E3For pleasant driving7LHD RHD LHD RHD

Introduction of outside air
E00702200235
To introduce air into the vehicle during hot
weather, set the air selection lever to the “
” (outside) position and set the tempera-
ture control dial to the positions shown in the
illustration. Be sure to set the temperature
control dial all the way to the left. Select the desired blower speed.
NOTEl Turn the mode selection dial clockwise and
air will flow to the leg area and the wind-
screen.Automatic air conditioning*
E00702400110
The air conditioning can only be used whilethe engine is running.
Control panel
E00702502551
Type 1Type 2
1- Mode selection dial
2- Blower speed selection dial
3- Temperature control dial
4- Rear window demister switch ® p. 5-43
5- Air conditioning switch
6- Air selection switch
NOTEl There is an interior air temperature sensor
(A) in the illustrated position.
Automatic air conditioning*
7-09OKTE15E3For pleasant driving7 LHD RHD

NOTENever place anything on top of the sensor,
since doing so will prevent it from function- ing properly.Blower speed selection dial
E00702800273
Select the blower speed by turning the blower
speed selection dial clockwise or anticlock- wise.
The blower speed will gradually increase as
the dial is turned to the right.
When the blower speed selection dial is set to
the “OFF” position, all fan-driven airflow
will stop.Temperature control dial
E00703000575
Turn the temperature control dial clockwise
to make the air warmer. Turn it anticlockwise
to make the air cooler.
Type 1Type 2

Automatic air conditioning*
7-10OKTE15E3For pleasant driving7 RHD
LHD

15- Display
RDS uses PI (program identification) signal and AF (alternative frequency) list transmitted in addition to the normal FM broadcasting programs, and picks up the FM stations that are transmitting the same program from the AF list and automatically tunes to the station with the strongestsignal intensity.
Therefore, you can continue listening to one program in, for example, a long distance driving without retuning to the other station transmitting
the same program when you are leaving the service area of the currently receiving station.
The RDS radio also features the limited reception of the program types, the break-in reception of the traffic announcement to the EON (enhanced
other network) and emergency broadcast, and the limited/unlimited reception of the regional programs.
AF (Alternative Frequencies)
function
E00720900061
The AF function finds a station broadcasting
the same program and selects the station with the strongest signal of AF lists.
The AF function is turned on (with the AF in- dicator (12) shown on the display) at all times unless you manually switch it off.

The AF function can be turned ON and OFF.
Refer to “Function setup mode” on page
7-24.
CT (Clock Time) function
E00721000131
The clock can be set automatically by using
the signal from the local RDS stations. Refer to “Adjusting the time” on page 5-12.
REG (Regional) function
E00721100057
REG function limits to receive the stations
broadcasting regional programs.
Regional programming and regional net- works are organized differently depending on
the country or area (they may be changed ac- cording to the hour, state, or broadcast area),
so if you don’t want to receive the regional
programs automatically, you can set up REG
ON not to receive regional programs.

The REG function can be turned ON and OFF.
Refer to “Function setup mode” on page
7-24.
PI (Program Identification)
search function
E00721200221
When travelling long distance and the recal-
led preset station is weak, the radio searches
another frequency broadcasting the same pro- gramming with the same PI code in AF list.
If there are no frequencies broadcasting the
same programming, the radio searches a fre-
quency broadcasting the regional program-
ming. The radio succeeds in searching the re- gional programming, then the display shows the REG indicator (11).
If the radio does not succeed in searching the
regional programming, the radio returns to
the recalled preset station.
The PI function can be turned ON and OFF.
Refer to “Function setup mode” on page
7-24.LW/MW/FM electronic tuning radio with CD player (audio system type 1) *
7-21OKTE15E3For pleasant driving7

2. Press the PWR/VOL key.Turn the power OFF.NOTEl Hold down the steering MODE key to also
turn the audio function ON/OFF.Adjust Volume
E00737300025
1. Turn the PWR/VOL key to adjust the
volume.
Turn the PWR/VOL key clockwise toincrease, and counter- clockwise to de-
crease the volume.
NOTEl The maximum value for volume is 45, and
the minimum is 0.NOTEl The initial setting for volume is “17”.Insert/Eject Discs
E00737400026
1.
Insert the disc into the disc slot with the
label surface up.
Push the disc in a certain amount, and
the product will pull the disc in, and playback will start.
2. Press the
key.
This will eject the disc from the product,
so remove the disc.
CAUTIONl When replacing discs, first ensure that the
vehicle is stopped in an area in which stop-ping is permitted.
l Do not insert your hand, fingers, or foreign
objects into the disc slot. This may lead to injury, smoking, or fire.
l 8 cm CDs are not supported.
Operation Keys (audio system type 2)
7-61OKTE15E3For pleasant driving7 Disc *Label sideDisc slot

NOTElThis switches in the order FM1, FM2, FM3,
DAB1*, DAB2*, DAB3*, MW, and LW. *:When a DAB tuner is connected.
Manual/Seek Station Selection
Turn the /SEL key to the frequency to lis-
ten to.
/SEL key
(counter-
clockwise)Reduces the frequency being
received./SEL key
(clockwise)Increases the frequency be-
ing received. key
(hold down)Release the button to start
seek station selection, and
when a station is received,
scanning stops. key
(hold down)
Preset Memory
Register the broadcast station in advance, and select this at a later time.
1. Tune in to the frequency to register.
2. Hold down any of the keys from the
1RPT key to the 6
key.

A “Beep” sounds, and the preset key is registered.NOTEl The preset memory can register a maximum
of 6 stations for each band (FM1, FM2,
FM3).
l If a preset key that already has a station reg-
istered is selected, then this is overwritten with the new preset.
l Pressing the preset key will select the previ-
ously registered frequency.
Auto Memory (Auto Store)
The top 6 stations with a strong signal can be
automatically registered in order with preset keys.
Hold down the RADIO key.

After completion of auto store operations, the
product will receive the station registered in
the preset key [1].
CAUTIONl Please be aware that the formerly-registered
frequency in the memory will be overwrit- ten.NOTEl Using auto store for FM1 and FM2 switches
to FM3.
PTY Search
Select PTY (program content), and automati-
cally scan for stations. 1. During FM reception, press the PTY/
SCAN key.
This switches to the PTY selection mode.
2. Turn the
/SEL key to select PTY.
The PTY (program content) indicator
will flash, and station selection will au- tomatically start. When a station is re-
ceived, the station name is displayed.
NOTEl This receives the station detected first.
l 10 seconds after reception, PTY search
mode will be cancelled.Listen to DAB (audio system
type 2) * E00739101024
This explains how to listen to DAB.
Listen to DAB (audio system type 2) *
7-64OKTE15E3For pleasant driving7

Display Indicator (audio system type 2)E00738101069
This explains content of the display indicator.

Audio Quality and Volume
Balance Adjustment (audio
system type 2) E00738201031
Change audio quality settings.Adjust Audio Quality and Vol- ume Balance
1. Press the /SEL key to select settings
items.

Each time the
/SEL key is pressed,
this switches in the order BASS, TRE-
BLE, FADER, BALANCE, SCV, and
Cancel.
2. Turn the
/SEL key to adjust.
Ad-
just-
ment
items
Turn counter- clockwiseTurn clockwise
BAS
S-6 to 0
(low low-pass
volume)0 to +6
(high low-pass
volume)TRE-
BLE-6 to 0
(Low high-pass
volume)0 to +6
(High high-pass
volume)
Display Indicator (audio system type 2)
7-75OKTE15E3For pleasant driving7