2015 AUDI R8 SPYDER Owners Manual

.... N
l'­
N "1: rl I.O
"' N
"' ....
(D Note
-Applying a higher vo ltage booster battery
will cause expensive damage to sensitive electronic components, such as control
units, relays, radio, etc.
- T here m ust be no e lectrica l contact between
the vehicles as otherwise current could al­
ready start to flow as soon as the pos itive
(+) terminals are connected .
@ Tips
-The discharged battery must be properly
con nected to the vehicle's electrical system.
- Switch
off any car phone, or follow the car
phone instruct ions for this situation.
Use of jumper cables
Make sure to connect the jumper coble clomps in
exa ctly the order described below!
F ig . 161 Luggag e comp artm ent: conn ectors fo r a charg er
an d jump start cab les
®
Fig . 162 Jump start using th e batte ry in a not her ve hicl e: A
• Fe male sock et, B • D isch arge
The batte ry is located in the luggage compart­
ment ~
page 166 . The front lid can be opened in
a n emergency
r=;, poge 33.
What do I do no w?
Do not connect the negative cable d irect ly to the
n egat ive terminal on the battery . Connect it to a
jump start pin instead r=;, fig. 161.
Connect the po sitive cable (r e d ) to the
po sitive terminal
1. Connect one end of the red jumper cab le
r=;, fig . 162 (D to th e positive t erminal of dis­
charged battery @.
2. Connect the o ther end of the red jumper ca­
ble to the positive term inal @ofthe booster
battery @.
Conne ct the neg ative c able (bl ack ) to the
neg ativ e terminal
3. Connect one end of the b lack jumper cable @
to the negative term inal of the booster bat­
tery @.
4. Secu re the other end to the jump start pin@
for the d isc harged battery @.
Starting the engine
"'Start the engine of the veh icle provid ing assis ­
tance and allow it to run at idle .
"' Now sta rt the engine of the vehicle with the
d ischa rged ba ttery.
"'I f the engine does not star t: Stop trying afte r
10 seconds and then try again after about 30
seconds .
"' Disconnect the cable while the engine is run-
ning in exact ly
reverse orde r to that described.
T he bat tery is vented to the outside to p reven t
gases from entering the vehicle interior . Make
s u re that th e jumper clamps ar e well connect ed
with their
metal ports in full contact with the
battery terminals.
A WARNING .
To avoid se rious personal injury and damage
to the veh icle , heed all warnings and ins truc­
tions of the jumper cable manufacture r. If in
doubt, call for road service.
- Ju mpe r cables m ust be long eno ugh so that
the vehicles do not touch .
- When connecting jumper cables, make sure
that they can not g et caug ht in any moving
parts in the eng ine compartment. ..,.
207

What do I do now?
- Be fo re you check a nything in t he e ngine
compartment, always read and heed all
WARNINGS
Q page 155, Working in the en­
gine compartment .
CD Note
Improper hook-up of jumper cables can ruin
the generator.
- Always connect POSITIVE( +) to POSITIVE
( + ), and NEGA TIVE(-) to NEGATIV E(-)
gro und post of the battery manager control
unit.
- Check that a ll screw plugs on the battery
cells are screwed in firmly . If not, tighten
plugs prior to connect ing clamp on negat ive
battery terminal.
- Please note that the procedure for connect­
i ng a jumper cable as described above ap­
plies specifically to the case of your vehicle
being jump started. When you a re g iving a
ju mp sta rt to another vehicle, do
not con­
n e ct the neg ative(- ) ca b le to the negative
( - ) terminal o n the discharged battery @.
Instead, se curely connect the negative(-)
cab le to either a solid metal component
that is f irm ly bolted to the engine block or
to the engine block itself . If the battery that
i s bei ng charged does not vent to the out­
s ide , escap ing battery gas could ignite and
explode!
Emergency towing with
commercial tow truck
General hints
Your Audi requires special handling for towing.
The fo llow ing in formation is to be used by com ­
mercial tow truck operators who know how to op ­
erate their equipment safely .
- Never tow your A ud i, tow ing will cause damage
to the engine and transmiss ion .
- Never wrap the safety chains o r winch cables
around the b rake lines.
- To preven t un ne cessary d am age, yo ur Audi
mus t be transpor ted with a car carrier ( flat bed
t ruck) .
208
-To load the vehicle on to the flat bed , use the
tow ing loop found in the vehicle tools and at­
tach to the front anchorage
Q page 208.
_& WARNING
A veh icle being towed is not safe for passen­
gers. Never a llow anyone to ride in a vehicle
being towed, fo r any reason.
CD Note
The vehicle has ver y low ground clearance.
M ake sure that no damage is caused to the
underside of the vehicle when it is being load­
ed onto a flat bed truck .
Front towing loop
Do not install the front towing loop un til it is
needed.
Fi g. 163 Righ t fro nt bu m per w it h ou t gr ille: Tow ing loo p
full y screwe d in
On the right front in the bumper , there is a
t h readed hole behind the air intake g rill into
which the tow ing loop is screwed .
.,. Remove the tow ing loop from the vehicle tool
kit
Q page 199 .
.,. Pull the lower part of the gr ill forward a nd out .
.,. Sc rew the tow ing loop t ightly into t he threaded
hol e as fa r as it will go
Q fig . 163 and tighten it
w ith the wheel w rench .
When it is no longer needed, unscrew the towing
l oop and put it back into the on-boa rd too lkit .
Make sure to have th e towing loop sto red in the
vehicle at all times .
When install ing the grill for the air duct, be sure
that the tabs on t he g rill a re first inserted into .,..

..... N
r-­N "': ..... \!) 1.1'1
N 1.1'1 .....
their guides on the vehicle. Then push the grill in­
to position.
A WARNING
If the towing loop is not screwed in as far as it
w ill go, the thread can pull out when the veh i­
cle is towed -potential risk of an accident.
(D Tips
Check carefully to make sure the hook- up is
secure .
What do I d o now?
209

Fuses and bulbs
Fuses and bulbs
Electrical fuses
Replacing fuses
Fuses that have blown will have metal strips
that have burned through .
Fig. 164 Passenger's s ide wheel well: Foot rest with fuse
arrangement
The fuses are located in the footwell area on the
passenger's side behind a cover .
.. Switch the ignition and all e lectrica l equipment
off .
.. Check the following table to see which fuse be-
longs to the equipment .
.,. Remove the floor mat .
.,. Fo ld the foot rest back~
fig. 164 .
.,. Remove the clamp from the holder in the fuse
box .
.. Remove the fuse using the clamp and replace
the b lown fu se with an ident ica l new one .
.. Fo ld the foot rest down again .
Fuse color identification
Color Current in amps
B lack 1
Purple 3
Light b rown 5
Brown 7 .5
Red 10
B lue 15
Yellow 20
Whit e or transparent 25
Green 30
Ora nge 40
210
A WARNING
Do not repa ir fuses and never replace a blown
f u se w ith one that has a highe r amp rating.
This can cause damage to the electr ica l sys­
t e m and a fire.
(D Note
If a new fuse blows again shortly after you
have installed it, have the electrical system
checked by an a uth orized Audi dea le r or a u­
thoriz ed Audi Serv ice Facility .
@ Tips
-The followi ng table does not list fuse loca­
t ions that are not used .
- Some of the equipment listed in the fo llow­
ing tables applies on ly to certa in model ver­
sions or certa in optiona l equipment .
Fuse assignment
Fig. 165 Pas senge r footwell: Fuse panel
Fuse panel @
No . Consumer
1 VOA interface
2 Heated windshield washer nozzle

..... N
r-­N "': ..... \!) 1.1'1
N 1.1'1 .....
Fuse panel @
No. Con sume r
3 Parking system
4 Engine compartment lid release
Diagnostic interface, light switch, indica-
5 tor l ight
P asse nger A ir Bag OFF , selector
lever
6 Networking gateway
7 Right headlight
Automatically d imm ing inside mirror, ga-
8 rage door opener (Homelink), washer
pump relay, power outlets relay
9 Left headlight
1 0
[!] button
11 Pressure sensor,
climate controls
12 Airbag
Fuse panel @
No. Consumer
1 Radiator
fan (1)
2 Rad
iator fan (2)
3 Exterior lighting
4 Exterior lighting
6 Blower regulator
Fuse pan el @
No. Con sumer
1 Rear view camera
2 Tire pressure monitoring system
4
Cell phone package, telephone antenna
amplifier
5 Instrument cluste r
6 Networking gateway
7 Steering column lever
8
Diagnostic
interface, brake pedal switch,
selector lever
9 Rain/light sensor
10 Light switch
1 1 Special functions contro
l modu le
1 5 Sound amplifier
16 Radio
Fu ses a nd bulb s
Fuse panel @
No . Con sumer
3 Auxiliary water pump
5 Supply terminal
15, starter
6 Pump for brake booster
7 Horn
8 Wiper motor
9 Wiper motor
10 Head light washer system
12 Power
outlets and cigarette lighter
Fuse panel ®
No . Con sumer
1 E lectronic Stabilization Program
2 Electronic Stabilization Program
3 Partition window defogger
4 Rear window defogger
5 Power locking system
6 Inter ior lights, washer nozzles
7 Anti-theft a larm system
8 Climate controls
9 Heated seats
10 Lumbar support
11 Control
module for doors
12 Control module fo r doors
Bulbs
Note
Your vehicle is equipped with maintenance -free
headlights and rear lights . Howeve r, if a bulb has
to be changed, please consult your autho rized
Audi dealer or other qualified workshop.
21 1

Technical Dat a
Technical Data
Vehicle identification
F ig. 166 Ve hicle Ident if icat ion Number (VlN) p late: loca·
tio n on d river 's side dash pane l
XXXXX XX -X -XX XX XXX XX
@-+ ~J:~t::1 ::: xxxxxxxx xx x xxxx xxx x
IYP lf'VPE XXX X XX
xx xxxxxxx xx xx xx
XXX KW
XXX
EM:. COil / fAANS , COOE xxxx XXX XXX ®i MOIOlll ©-+ IAC KIIR . / tNN EN AIJSSt
XXXX I XXXX XXX I XX PAI NT NO./ WT£Jldl
II. -AUSST. / OPTIO NS
E0 A 7D5 4UB 6X
M SSG SR W
2EH JOZ lLB lAS
1BA
3FC SM U 7 X1
F0 A
9G3 0
G7 0Y H
0JF
TL 6 3 KA 8EH UlA X 9B Q
Z7
l XW
803 908
8Z4 020
7T6 C V7 7 K0 4X3 2K2
3L4 4KC 3Y0 413
502
lS A 7GB 01A
4G0
XX X XX X
XX X xxxx
Fig. 167 The ve hicle ide ntif ic ati on label - inside t he lug ·
gage compar tmen t
Vehicle Identificat ion Number (VlN )
The Veh icle Iden tifica tion Number is located in
differen t places :
- u nder the windshield on the driver· s side
¢ fig . 166.
-in the Dr iver Informat ion disp lay ~ page 22 .
- on the vehicle identification label.
212
V ehicle identification label
The Vehicle iden tifica tion label is located with
the fuses in the footwe ll on the passenger's side
¢ page 210 .
The label ~ fig. 167 shows the fo llow ing vehicle
da ta:
(D Vehicle Ident ificat ion Number (VIN)
@ Vehicle ty pe, engine o utp ut, t ransmission
® E ngine and transm ission code
@ Pa int number and inte rior
® Optional eq uipment numbers
The information of the vehicle identification label
can a lso be fo und in your Warranty
& Ma inte­
nance booklet.
Safety compliance sticker
The Safety compliance sticke r is your assurance
that your new veh icle complies with all appli cable
Federa l Mo to r Veh icl e Safety Standards which
were in effect at the time the vehicle was man u­
factu red. Yo u can find this sticker on the left door
j amb.
It shows the month and year of production
and the vehicle ident ificat ion number of your ve·
hide (perforation) as well as the Gross Vehicle
Weight Rating (GVWR) and the Gross Axle
We ight Rating (GAWR) .
High volt age warning label
The hig h voltage warning label is located on the
l ock carrier. The spark ignit ion system complies
with the Canadian standard ICES-002 .
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for front
and rear are listed on a st icker on the left door
jamb .
T he Gross Vehicle Weight Rating includes the
weight o f the basic vehicle plus fu ll fuel tank, oil
and coolant, pl us maxim um load, which includes
passenger weight (150 lbs/68 kg per designated
seat ing pos ition) and luggage we ight.
1111>