M N
co ~ co
rl I.O
"' N
"' rl
_& WARNING
Always read and follow all WARNINGS and in
formation
c> A in Raising the vehicle on
page 262
and c> page 264 .
After changing a wheel
A wheel change i s no t comple te withou t the do
ing the following .
.. Always store the vehicle tool kit, the jack* and
the replaced tire in the luggage compartmen t
c>page 140 .
.. As soon as possible, have the tightening tor
ques
on all wheel bolts checked w ith a torque
wrench . The correct tightening torque is
105
ft lb (140 Nm) .
.. Have the flat tire
replaced as soo n as poss ible.
{1) Tips
- If you notice that the wheel bolts are cor
roded and diffi cult to turn while changing a
tire, they should be replaced before you
check the tightening torque.
- Drive at reduced speed until you have the
tightening torques checked .
Decorative wheel covers
Applies to vehicles: with decorative wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts .
Fig. 216 Chan gin g a wheel: Removing the wheel cove r
Removing
.. Insert the hook provided with the veh icle tool
kit in the hole in the hub.
.. Pull off the
decorative wheel cover c> fig. 216.
Emergen cy assistance
Wheels with wheel bolt caps
Applies to vehicles: with wheel bolts with caps
The cops must be removed firs t from the wheel
bolts before the bolts can be unscrewed .
Fig. 217 Changing a wh eel: re movin g the wheel bo lt ca ps
Removing
.. Push the plastic clip provided wi th the vehicle
too l kit over the wheel bolt cap until it engages.
.. Pull on the
plastic clip to remove the cap
c>fig. 217.
Refitting
.,. Place the caps over the wheel bolts and push
t hem back on.
The caps are to protect and keep the wheel bolts
clean.
Loosening and tightening the wheel bolts
The wheel bolts must be loosened before raising
the vehicle .
Fig. 218 Changing a whe el: loosening th e w hee l bol ts
Loosening
.. Insta ll the wheel bolt wrench over the wheel
bolt and push it down as far as it will go. ..,.
261
Emergency assistance
"' Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel bolts
slightly.
"'Remove the alignment pin and insert and tight
en the remaining wheel bolt slightly like the
rest.
"'T urn the jack handle* counter-clockwise to low
er the vehicle until the jack* is fully released .
"'U se the whee l bolt wrench to tighten all wheel
bolts firmly¢
page 261. Tighten them cross
wise,
from one bolt to the (approximately) op
posite one, to keep the wheel centered.
@ Note
When removing or installing the wheel, the
r im could hit the brake rotor and damage the
rotor. Work carefu lly and have a second per
son help you.
(D Tips
Never use the hexagonal socket in the handle
of the screwdriver to loosen or tighten the
wheel bolts.
- Pull the reversib le blade from the screwdriv
er before you use the hexagonal socket in
the handle to turn the wheel bolts.
- When mounting tires with
unidirectional
tread design
make sure the tread pattern is
pointed the right way
¢page 264.
-The wheel bolts should be clean and easy to
turn. Check for dirt and corrosion on the
mating surfaces of bot h the wheel and the
hub. Remove all dirt from these surfaces be
fore remounting the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right direction.
Using a spare tire with a tread pattern
intended for use in a specific direction
When us ing a spare tire w ith a tread pattern in
tended for use in a specific direct ion, please note
the following:
- The direction of rotation is marked by an arrow
on the side of the tire .
264
-If the spare tire has to be installed in the incor
rect direction, use the spare tire only tempora
r il y since the tire w ill not be ab le to achieve its
optimum performance character istics with re
gard to aquaplaning, noise and wear.
- We recommend that you pay part icu lar atten
tion to th is fact during wet weather and that
you adjust your speed to match road condi
tions.
- Replace the flat tire with a new one and have it
installed on your veh icle as soon as possible to
resto re the handling advantages of a unidirec
tional tire.
Notes on wheel changing
Please read the information ¢ page 242, New
tires ar wheels
if you are going to use a spare tire
which is different from the tires on your vehicle .
After you change a tire:
- Check the tire pressure on the spare immedi
ately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos
sible by your authorized Audi dealer or a
qualified workshop.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
105 ft lb (140 Nm).
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire,
they should be replaced before you check the
tightening torque.
- Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi
ble. Remount the wheel cover.
Until then, drive with extra care and at reduced
speeds.
&_ WARNING
- If you are going to equ ip your vehi cle w ith
tires or rims which differ from those which
were factory installed, then be sure to read
the information ¢
page 242, New tires or
wheels .
-
