2014 RENAULT SCENIC engine

PETROL INJECTION
Fault finding – Conformity check17B
17B-97V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
DRIVER PARAMETERS SUB-FUNCTION
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1
Motorised
throttleET085: Motorised throttle
in defect modeNO
STATUS 0
STATUS 1
STATUS 2
STATUS 3
STATUS 4
STATUS 5WITHOUT
2 ET051: Throttle stop
programmingCOMPLETED
Run command RZ005
Programming. If the parameters
and statuses are still incorrect,
contact the Techline. 3 PR097: Motorised throttle
lower stop
programmed
value.5.96% < PR097
< 13.96%
4 PR113: Throttle lower stop
after applying
Offset5.96% < PR113
< 13.96%
5 PR096: Motorised throttle
upper stop
programmed valuePR096 = 87.99%
6 ET082: Motorised throttle
positionOPEN
CLOSED
NOT DETECTEDIf NOT DETECTED, apply
interpretation of ET082 Motorised
throttle valve position.
7 PR118: Motorised throttle
position gang 1No load = 4%
Full load = 99.02%If there is a fault, use the
interpretation for DF095 Throttle
potentiometer circuit gang 1.
8 PR119: Motorised throttle
position gang 2No load = 4%
Full load = 100%If there is a fault, use the
interpretation for DF096 Throttle
potentiometer circuit gang 2.
9 PR116: Motorised throttle
corrected position
setpointNo load = 0%
Full load = 60%
WITHOUT
10 PR111: Motorised throttle
position corrected
value.No load = 0%
Full load = 60%
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B-99V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
PREHEATING/IGNITION SUB-FUNCTION
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1 Flywheel target ET089: Flywheel target
programmingCOMPLETED
WITHOUT 2 Engine phasing ET061: Cylinder 1
recognitionNOT PERFORMED
3 Flywheel ET062: Flywheel signalNOT DETECTED
4
IgnitionPR001: Advance0 °V
5PR095: anti-pinking
correction0 °V
6 Flywheel ET581: Petrol misfireNO
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B-100V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
EMISSION CONTROL/OBD SUB-FUNCTION
* OCR: Opening Cyclic Ratio
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1
Oxygen
sensorET052: Upstream O
2
sensor heatingACTIVE
INACTIVEIf ACTIVE, apply the
interpretation of ET052
Upstream O
2 sensor
heating.
2 ET053: Downstream O
2
sensor heatingACTIVE
INACTIVESi ACTIF, apply the
interpretation of ET053
Downstream O
2 sensor
heating.
3PR098: Upstream oxygen
sensor voltage120 mV < PR098
<750mVIf there is a fault, use
interpretation of PR098
Upstream oxygen sensor
voltage.
4PR099: Downstream
oxygen sensor
voltage120 mV < PR099
<750mVIf there is a fault, apply the
interpretation of PR099
Downstream oxygen
sensor voltage.
5
CanisterET050: Canister bleed
controlINACTIVE
WITHOUT
6PR102: Canister bleed
solenoid valve
OCR*0% < PR102
< 99.61%
7 Flywheel ET581: Petrol misfireNO
8 Canister AC017: Canister bleed
solenoid valveThe canister bleed
solenoid valve
should be heard
operatingIn the event of a fault, apply
interpretation of AC017
Canister bleed solenoid
valve.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B-102V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
COLD LOOP SUB-FUNCTION
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1
Air
conditioningET079: Air conditioning
presentShows whether or not the
vehicle is equipped with air
conditioning.
YES: Air conditioning is detected
by the injection computer.
NO: Air conditioning is not
detected by the injection
computer.If inconsistent
with the vehicle
equipment, carry
out a multiplex
network test and
apply the
relevant
procedure.
2ET088: Compressor
actuation
requestThe injection requests the UPC
(via the multiplex network) to
start the compressor.
ACTIVE: The multiplex network
should not be faulty on the
Automatic Transmission, UPC or
UCH systems. The UCH must
send a compressor starting
request to the injection. The
coolant pressure sensor must not
be defective.
Satisfactory engine operating
conditions (coolant temperature,
engine load etc.).
INACTIVE: One of the above
conditions has not been met.WITHOUT
3ET004: Air conditioning
authorisationNon operational information,
intended solely for diagnostic
purposes.
YES: Satisfactory engine
operating conditions (coolant
temperature, engine load etc.).
The vehicle is not in a specific
movement phase (hill start or
stop etc.).
NO: One of the above conditions
has not been fulfilled.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B-103V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
COLD LOOP SUBSYSTEM(continued 1)
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
4Refrigerant
pressurePR037: Refrigerant
pressure2bar Default value: 0 barIf there is a fault, use the
interpretation for PR037
Coolant pressure.
5 Engine speed PR055: Engine
speedShows the speed of
rotation in rpm.
0rpm < 500 rpmIn the event of a fault apply
the interpretation for DF154
Flywheel signal sensor
circuit.
6Motorised
throttleET023: Fast idle
speed
requestUCH requests the
injection system to
increase the idling speed.
ABSENT: The UCH has not
made a request.
PRESENT: The UCH has
made a request.If ET023 is inconsistent,
run a multiplex network
test using the diagnostic
tool; then if the test is in
order, consult the UCH.
7 Coolant
temperaturePR064: Coolant
temperature- 40°C < PR064 < 120°CIn the event of a fault, apply
the interpretation of DF001
Coolant temperature
sensor circuit.
8Vehicle
speedPR089: Vehicle
speedGives the vehicle speed in
mph (km/h). This
parameter is sent to the
injection by the ABS
computer via the multiplex
network.In the event of a fault, apply
the interpretation of DF091
Vehicle speed signal.
9Air
conditioningPR125: Power used
by the AC
compressor300 W WITHOUT
10
GMVET014: Fan
assembly 1
checkRUNNING
STOPPEDIf the ET014 is
inconsistent, carry out a
multiplex network test
using the diagnostic tool.
If the test is correct check
the UPC.
11 ET015: Fan
assembly 2
checkRUNNING
STOPPEDIf the ET015 is
inconsistent, carry out a
multiplex network test
using the diagnostic tool.
If the test is correct check
the UPC.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B-104V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
HEATING SUB-FUNCTION
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1Coolant
temperaturePR064: Coolant
temperature- 40°C < PR064 < 120°CIn the event of a fault,
apply the
interpretation of
DF001 Coolant
temperature sensor
circuit.
2
Passenger
compartment
heating
resistorET111: Number of
fixed heating
resistorsThis status indicates that the
injection computer is
preventing any change to the
number of passenger
compartment heating
resistors (RCH) activated
(RCH already activated are
not shut down, but no more
can be added). This limit in
the number of RCH is in
response to the vehicle's
requirements (power
availability, torque
requirement, etc.).WITHOUT
3ET112: Passenger
compartmen
t heating
resistor cut-
offThis status indicates that the
injection computer is
inhibiting all the passenger
compartment heating
resistors (RCH) in response
to the vehicle's requirements
(power availability,
torque requirement,
injection or air conditioning
defect mode, etc.).
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B-105V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
CRUISE CONTROL/SPEED LIMITER SUB-FUNCTION
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1
Cruise
control/
Speed
limiterET042: Cruise control/
speed limiter.- NOT DETECTED: Vehicle
not equipped with cruise
control/speed limiter function
buttons or after reprogramming
or programming the injection
computer, the switch is in the
rest position.
– INACTIVE: When no buttons
are pressed.
- SPEED LIMITER: Main
switch in speed limiter position.
- CRUISE CONTROL: Main
switch in cruise control
position.In the event of a fault,
apply the interpretation
of status ET042 Cruise
control/Speed limiter.
2 ET703: Cruise control/
speed limiter
buttons- INACTIVE: No cruise control/
speed limiter button is pressed.
- PLUS: When the cruise
control/speed limiter "+" button
is pressed.
- MINUS: When the cruise
control/speed limiter "-" button
is pressed.
- SUSPEND: When the cruise
control/speed limiter "0" button
is pressed.
- RESUME: When the cruise
control/speed limiter "R" button
is pressed.In the event of a fault,
consult the
interpretation of status
ET703 Cruise control/
speed limiter button.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B-106V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
CRUISE CONTROL/SPEED LIMITER SUB-FUNCTION (CONTINUED 1)
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
3
Brake
contactET704: Brake switch
No. 1- ACTIVE (brake pedal
depressed)
- INACTIVE (brake pedal
released)In the event of a fault,
consult the
interpretation of status
ET704 Brake switch
No. 1.
4 ET705: Brake switch
No. 2- ACTIVE (brake pedal
depressed)
- INACTIVE (brake pedal
released)In the event of a fault,
consult the
interpretation of status
ET705 Brake switch
No. 2.
5Clutch pedal
switchET405: Clutch pedal
switch- ACTIVE
- INACTIVEIn the event of a fault,
consult the
interpretation of status
ET405 Clutch switch.
6Cruise
control
setpointPR130: Cruise control
setpointIndicates the reference value
requested by the driver
(in mph (km/h))WITHOUT
JSAA741