2014 RENAULT SCENIC engine

PETROL INJECTION
Fault finding – Conformity check17B
17B-107V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
CRUISE CONTROL/SPEED LIMITER SUB-FUNCTION (CONTINUED 2)
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
7 Cruise
control/speed
limiter
deactivationET415: Cruise control/
speed limiter
deactivationNONE: This status is present
on the diagnostic tool when:
– The computer has been
reinitialised.
– The computer has been
reprogrammed.
In the event of a fault,
consult the
interpretation of status
ET415 Cruise
control/speed limiter
deactivation. - STATUS 1: Traction control
request
- STATUS 2: Brake pedal
depressed.
- STATUS 3: Clutch pedal
depressed.
- STATUS 4: Suspend button
pressed.
- STATUS 5: Cruise control or
speed limiter monitoring.
- STATUS 6: Gear lever in
neutral (manual gearbox) or N
position (automatic
transmission).
- STATUS 7: Inconsistency
between the request and the
vehicle speed.
- STATUS 8: Automatic
transmission in defect mode.
- STATUS 9: Vehicle speed
monitoring.
- STATUS 10: Monitoring by
injection computer.
JSAA741

PETROL INJECTION
Fault finding – Conformity check17B
17B-108V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
START SUB-FUNCTION
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
Order FunctionParameter or Status
Checked or ActionDisplay and
notes Fault finding
1 Starting ET076: StartingAUTHORISEDThe authorisation to start is
given once the fuel pump is
pressurised and if the
motorised throttle has
completed its stop and limp-
home position programming
phase.
2Actuator relay
controlET048: Actuator relay
controlACTIVE
INACTIVEIf ACTIVE apply the interpretation
of DF084 Actuator relay control
circuit.
3 Battery voltage PR071: Computer feed
voltage11 V < PR071
<15VIf there is a fault, use
interpretation of PR071
Computer supply voltage.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B-109V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
PROTECTION SUB-FUNCTION
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1Code
programmedET006: Code
programmedStates whether the
immobiliser code has been
programmed by the
computer or not.
YES: Code programmed
NO: Code not programmed
into the injection computer.If NO, contact the
Techline
2Engine
immobiliserET003: Engine
immobiliserIndicates the status of the
immobiliser system.
INACTIVE: The injection
computer has recognised the
immobiliser code transmitted
by the UCH.
ACTIVE: the injection
computer does not recognise
the immobiliser code
transmitted by the UCH.If ET003 is
inconsistent, carry
out a multiplex
network test using
the diagnostic tool. If
the test is correct
check the UCH.
3Impact
detectedET077: Impact
detectedYES
NOIf YES, switch off the
ignition for 10
seconds, then
switch it back on so
the engine can be
restarted. Then clear
any faults.
4 Starting ET076: StartingAUTHORISEDThe authorisation to
start is given once
the fuel pump is
pressurised and if
the motorised
throttle has
completed its stop
and limp-home
position
programming phase.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B-110V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
TORQUE MANAGEMENT SUB-FUNCTION
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
Order FunctionParameter or Status Checked
or ActionDisplay and notes Fault finding
1
TorquePR100: Torque lapse0N.m
If there is a fault, test
the multiplex network; if
the test is OK, check the
automatic
transmission. 2 PR015: Engine torque0N.m
3 PR123: Estimated driver
demand engine
torque0 Nm < PR123
<200Nm
4 PR122: Torque received by
automatic
transmission
converter0N.m
5 PR124: Resistant engine
torque transmitted via
multiplex line0N.m
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
1 7 B - 111V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
MAIN COMPUTER STATUSES AND PARAMETERS
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, at idle speed.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1
Battery
voltagePR071: Computer
feed voltage13 V < PR071 < 15 V
If there is a fault, use
interpretation of
PR071 Computer
supply voltage. 2 ET001: Computer +
after ignition
feed+ after ignition feed absent
3Water
pumpET543: Coolant
pump controlFor F4R Turbo engine only.
ACTIVE: coolant pump running
INACTIVE: coolant pump idleIn the event of a fault,
apply interpretation of
DF086 Coolant
pump relay control
circuit.
4Vehicle
speedPR089: Vehicle
speedGives the vehicle speed in mph
(km/h). This parameter is sent to
the injection by the ABS
computer via the multiplex
network.If there is a fault use
the interpretation for
DF091 Vehicle speed
signal.
5Clutch
contactET040: Clutch pedalIndicates recognition of clutch
pedal contacts.
RELEASED: Pedal released
DEPRESSED: Pedal depressed
UNAVAILABLE: Automatic
transmission onlyIn the event of a fault,
use the interpretation
of ET040 Clutch
pedal.
6Brake
contactET039: Brake pedalIndicates recognition of brake
pedal contacts.
RELEASED: Pedal released
DEPRESSED: Pedal depressedIf there is a fault, use
the interpretation for
ET039 Brake pedal.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B-113V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
FUEL CIRCUIT SUB-FUNCTION
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, at idle speed.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1Engine
speedPR055: Engine
speedIndicates the engine's speed of
rotation in rpm.
700 rpm < PR055 < 6500 rpmIn the event of a
fault, apply the
interpretation for
DF154 Flywheel
signal sensor
circuit.
2
Motorised
throttlePR014: Idling
speed
correctionShows engine idling speed
correction value.
0 rpm < PR014 < 224 rpm.
The idle speed regulator performs all
of the calculations that allow the idle
speed actuator to be controlled
physically: the motorised throttle.
This regulator has a built-in adaptive
component (variation and ageing
programming).WITHOUT
3ET054: Idle speed
regulationACTIVE
INACTIVEIf INACTIVE apply
the interpretation for
ET054 Idling speed
regulation.
4 PR010: Idle speed
regulation
setpointThe idle speed regulation setpoint
depends on the coolant and oil
temperature, the position of the gear
lever, and which electrical
consumers are operating.
752 rpm < PR010 < 1216 rpm.
If a manifold pressure sensor fault is
present or stored, the idle speed
setting is 896 rpm.In the event of a
fault, apply the
interpretation of
ET054 Idle speed
regulation.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B-114V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
FUEL CIRCUIT SUB-FUNCTION (continued 1)
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
5
Motorised
throttlePR090: Idle speed
regulation
programming
value- 12% < PR090 < 12%
PR090, an adaptive built-in action, is
a stored parameter designed to
program variation and engine ageing
for the idle speed regulator. These
are programmed only when the
engine is idling and warm, and no
electrical consumers (electrical
windscreen, air conditioning, GMV,
power steering) have been selected.
Therefore it adjusts slowly.
WITHOUT
6 PR141: Integral idling
speed
regulation
correction4.7% < PR141 < 32%
The built-in correction is
continuously calculated to take into
account consumer demand for air.
7 Motorised
throttlePR091: Theoretical idle
speed
regulation OCR5% < PR091 < 50%
When the conditions for regulation
are met, the idle regulator continually
repositions the motorised throttle to
keep the engine speed at the idling
speed setting. The motorised throttle
opening ratio required to adhere to
the engine speed setpoint is then
given by parameter PR091.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B-117V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
SUB FUNCTION: CIRC. (TURBOCHARGING/INLET)
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, at idle speed.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1
Air circuit
pressurePR035: Atmospheric
pressure700 mb < PR035
< 1047 mbIf not consistent, check
PR035 = PR032 = local
atmospheric pressure, with
the engine stopped and
ignition on.
In the event of a fault apply
the interpretation for PR032,
Inlet pressure 2PR032: Inlet pressure114.1 mb < PR035
< 2200 mb
3
TurbochargingPR041: Turbocharging
pressure121.5 mb < PR041
< 2200 mb
Default value:
1016 mbIn the event of a fault, apply
the interpretation of DF004
Turbocharging pressure
sensor circuit.
4PR104: Turbocharging
solenoid valve
OCR setpointShows the
turbocharging
solenoid valve
opening ratio.WITHOUT
5 Air temperature PR058: Air temperature- 40°C < PR058
< 120°CIn the event of a fault, apply
the interpretation of DF002
Air temperature sensor
circuit.
6Coolant
temperaturePR064: Coolant
temperature75°C < PR058
< 120°CIn the event of a fault, apply
interpretation of DF001 Air
temperature sensor circuit.
7 Turbocharging AC004: Turbocharging
solenoid valveThe turbocharging
solenoid valve
should be heard
operatingIn the event of a fault, apply
interpretation of DF054
Turbocharging solenoid
valve control circuit.
JSAA741.0