2014 PORSCHE 911 TURBO brake

Driving and Driving Safety 165
–“ACC not possible Switch on PSM” Adaptive cruise control is not available because PSM was switched off.For information on Porsche Stability Management (PSM) :fPLEASE SEE THE CHAPTER “PORSCHE STABILITY MANAGEMENT (PSM)” on page 181.–“ ACC off” Adaptive cruise control was deactivated.– “ACC not possible Steering lock too large” The steering is turned too far.
General information
“Sport” and “Sport Plus” Mode
Adaptive cruise control regulates your driving more dynamically in “ Sport” and “Sport Plus” mode.
Exceptions for adaptive cruise control
Adaptive cruise control is not available in the following situations:– If the ignition is switched off.– When PSM is off.– If the driver’s door is opened and the driver’s safety belt is not fastened.– When parking or maneuvering in very tight spaces.– When the electric parking brake is activated.– If the PDK selector lever is in position N , R or P. – On upward or downward slopes of more than 15 %.
If one of these exception situations occurs when adaptive cruise control is switched on, adaptive cruise control will be switched off.A message to this effect appears on the multi-function display.
Warning messages
Overtake request when adaptive cruise control is active (ACC active)
If adaptive cruise control detects that braking assistance is required on the part of the driver, a warning signal sounds and the warning message “ Distance Please brake” appears on the multi- function display.
In this case, the braking power of the adaptive cruise control is not sufficient to prevent a collision.fBrake immediately.
Traffic situations in which vehicles cannot be reliably detected
The radar sensor for adaptive cruise control scans a narrow, cone-shaped area in front of your vehicle.Detection can be limited or unreliable, depending on the traffic situation and the size of the vehicle in front. The system may brake too late or unexpectedly.Stationary vehicles are not detected. The system cannot respond to stationary vehicles.fDrive with extreme care.fSlow down if necessary.
Inadequate braking power during automatic braking by the adaptive cruise control.
WARNINGh
14_991_Turbo_21.book Seite 165 Mittwoch, 9. April 2014 2:19 14

Driving and Driving Safety 167
Active Safety – Porsche “Active Safe”
The adaptive cruise control sensor is used for the Porsche “Active Safe” functions.
These include: – Brake system prefilling Prefilling of the brake system if the radar sensor detects that the vehicle is coming critically close to a moving obstacle in order to bridge the air gaps and improve braking response.– Brake Assist Reduction of the activation threshold of the Brake Assist function if the sensor detects that the vehicle is coming critically close to a moving obstacle.The activation threshold of the Brake Assist function is reduced in three stages, depending on how critical the danger situation is.– Target braking If the radar sensor detects that the vehicle is coming critically close to a moving obstacle and, at the same time, braking power is inadequate, brake pressure can be increased in accordance with the situation, through to full braking if required.
Information
All Porsche “Active Safe” functions are active for speeds of more than 20 mph (30 km/h).
Latent warning (visual)
If the vehicle is driving too close to the vehicle in front for a long time, to avoid a collision if the vehicle in front brakes, a latent warning appears on the multi-function display to warn the driver.fStay further back from the vehicle in front if necessary.
Prewarning (acoustic and visual)
If the radar sensor detects that the vehicle is coming critically close to and is very likely to collide with a moving obstacle in front, an acoustic and visual prewarning is issued. This warns the driver and still allows a collision to be prevented if the driver reacts accordingly.
Risk of collision with the vehicle in front.fBrake immediately.
Insufficient distanceWARNINGh
14_991_Turbo_21.book Seite 167 Mittwoch, 9. April 2014 2:19 14

168 Driving and Driving Safety
Acute warning (acoustic, visual and tangible)
If the driver does not react to the prewarning by braking, this is quickly followed by an acute warning, which involves a braking jolt as well as the acoustic and visual warning.
A braking jolt is felt in the vehicle as a result of a very quick build-up of brake pressure. This alerts the driver to the traffic situation. The driver can still prevent a collision by reacting accordingly in this dangerous situation.
Risk of collision with the vehicle in front.fBrake immediately.
Information
The situations described below lead to the assumption that the driver is driving carefully and the prewarning and acute warning functions are disabled:– The driver drives around tight corners.– The driver is braking.– If the driver accelerates sharply, this action is interpreted as an active driving request (e.g. indicating the driver’s intention to overtake).
Switching Porsche “Active Safe” warnings on/off
The latent warning and prewarning functions are switched off by default. The acute warning function is active. Latent warnings and prewarnings can be activated under “ Prewarning on” on the multi-function display.
The settings remain stored when the ignition is switched on and off.fPLEASE SEE THE CHAPTER “ACTIVE SAFETY – PORSCHE “ACTIVE SAFE”” on page 167.
Car Audio Operation/Tips
For radio operation see your radio manual which is included with your on-board literature.
FM reception
A vehicle is not an ideal place to listen to a radio. Because the vehicle moves, reception conditions are constantly changing. Buildings, terrain, signal distance and noise from other vehicles are all working against good reception. Some conditions affecting FM may appear to be problems when they are not.
The following characteristics are completely normal for a given reception area, and they do not indicate any problem with the radio itself.
Information
Electronic accessories should only be installed by your authorized Porsche dealer.Equipment which has not been tested and approved by Porsche may impair radio reception.
Fading and drifting
FM range is limited to about 25 miles (40 km), except for some high power stations.
If a vehicle is moving away from the desired station's transmitter, the signal will tend to fade and/or drift. This condition is more prevalent with FM than AM, and is often accompanied by distortion.Fading and drifting can be minimized to a certain degree by careful attention to fine tuning or selection of a stronger signal.
Insufficient distanceWARNINGh
14_991_Turbo_21.book Seite 168 Mittwoch, 9. April 2014 2:19 14

172 Driving and Driving Safety
Porsche Doppelkupplung (PDK)
Porsche Doppelkupplung (PDK) is a seven-speed transmission with an automatic and a manual selection mode.
In automatic selection mode (selector-lever position D), gear changing is automatic. You can change temporarily from automatic to manual mode using the shift buttons on the steering wheel.
In manual selection mode (selector-lever position M), you change gear using the shift buttons or shift paddles on the steering wheel or with the PDK selector lever.
You can change between selector-lever positions D and M as you wish while driving.
Information
fTake care not to operate the shift buttons on the steering wheel inadvertently in either automatic or manual mode, thereby triggering undesired gear changes.
Changing selector-lever position
The selector lever is blocked in the P position when the ignition is switched off.
When the ignition is switched on, the selector lever can be moved from position P and N only when the release button is pressed, and when the brake pedal is pressed.
Release button
The release button ( arrow) in the selector lever prevents the gear from being changed unintentionally.The release button must be pressed when shifting to position R or P.
Starting
The engine can be started only if the brake pedal is depressed and the selector lever is in position P or N.
Driving off
fOnly select the desired position for driving off ( D, M or R) when the engine is idling and the brake pedal is pressed.fSince the vehicle crawls when in gear, do not release the brake until you are ready to drive off.
Driving off on hills
The Drive-Off Assistant assists the driver when driving off on hills. The vehicle is held on the slope for a short time during the change from the brake pedal to the accelerator to facilitate driving off immediately after the brake is released.fPlease see the chapter “HOLD FUNCTION: DRIVE-OFF ASSISTANT, STANDSTILL MANAGEMENT” on page 184.
Stopping
fFor a brief stop, e.g. at traffic lights, leave the selector lever in drive position and hold the vehicle with the brake pedal.fDo not hold the vehicle on a slope using the accelerator. Use the brake pedal or the electric parking brake instead.fBefore leaving the vehicle, always apply the electric parking brake and move the selector lever to position P.
Parking
fGo easy on the accelerator!fWhen parking or maneuvering in a small space, control the speed by careful use of the footbrake.
14_991_Turbo_21.book Seite 172 Mittwoch, 9. April 2014 2:19 14

Driving and Driving Safety 173
Indicator for selector-lever position and engaged gear
When the engine is running, the display shows the selector-lever position and engaged gear.
If the selector lever is between two positions
Effects: – The corresponding selector-lever position in the instrument panel flashes and the warning “ Activate brake” or “Engage gear selector properly ” appears on the multi-function display .
Action required:fOperate the footbrake and engage the selector lever properly.
If the selector lever is inadvertently moved from P or N into a gear (due to a fault or improper use) without pressing the brake, this gear will also flash on the display and no power transmission will occur. fTo drive off, press the brake and move the selector lever from P or N into the required gear again.
Selector-lever position R or D flashes in the instrument panel
No power transmission occurs.
Effects: – The selector lever was engaged without the footbrake being depressed. – The selector lever was moved to R above the permissible limit speed.
Action required:fPress the footbrake and engage the required selector-lever position again from P or N. If reverse gear fails:fPlease see the chapter “LIMP-HOME MODE” on page 178.
Failure of the selector lever display on the instrument panel
Transm. failure Park vehicle safely
The warning “ Transm. failure Park vehicle safely ” is displayed in red on the multi-function display.
Effect: – No selector-lever position is displayed on the instrument panel.Vehicle can be driven only until it comes to a stop.
Action required:fIt is not possible to continue driving. Stop the vehicle immediately in a suitable place. Have the fault corrected at an authorized Porsche dealer. If the vehicle has to be towed:Please see the chapter “TOWING” on page 278.
If there is a fault in the transmission:
The warning “ Transm. fault Poss. no R gear Drive on poss. ” or “Drive temperature too high Reduce load ” appears on the multi-function display .fPlease see the chapter “LIMP-HOME MODE” on page 178.fHave the fault corrected immediately at an authorized Porsche dealer.
14_991_Turbo_21.book Seite 173 Mittwoch, 9. April 2014 2:19 14

174 Driving and Driving Safety
Selector-lever Positions
P – Parking lock
fEngage parking lock only when the vehicle is stationary.If selector-lever position P is flashing in the instrument panel, the parking lock is not engaged. The vehicle can roll away.Shift again from selector-lever position R to P.fActivate the electric parking brake and then engage the parking lock.If selector-lever position P is flashing in the instrument panel, the parking lock is not engaged. The vehicle can roll away.Shift again from selector-lever position R to P.
Vehicles without Porsche Entry & Drive: The ignition key can only be removed in selector- lever position P.
R – Reverse gear
fSelect only if the vehicle is stationary and the brake is applied.
N – Neutral
Selector-lever position N must be selected for towing or in car washes, for example.fOnly select the desired position for driving off ( D, M or R) when the engine is idling and the brake pedal is pressed.
D – Automatic selection mode
Select position D for “normal” driving. The gears are shifted automatically according to the accelerator position and speed.
Depending on the way the vehicle is driven (economical, comfortable or sporty driving style) and on the resistance (e.g. uphill), the gear-changing points are shifted towards higher or lower engine-speed ranges.The accelerator position, driving speed, engine speed, longitudinal and lateral acceleration and the road profile all have an influence on the gear-changing characteristic.
Unwanted upshifts, e.g. when entering bends, are prevented by swiftly releasing the accelerator pedal.
Depending on lateral acceleration, upshifts on bends are not made until the engine-speed limit is reached.
When you brake, and depending on the amount of deceleration, the PDK transmission changes down earlier.For subsequent cornering, the correct gear is engaged when pressure is applied to the brakes before the bend. The bend is taken in the right gear, and when you accelerate out of the bend you do not have to change down.
With a sporty driving style, downshifts are already initiated when the brake pedal is touched lightly. This further enhances a dynamic driving style.
The PDK transmission temporarily changes to the sportiest gear-changing map, i.e. to the highest possible gear-changing points, if the accelerator pedal is pressed quickly. The transmission accordingly shifts down immediately by one or two gears (temporary downshift).
The transmission no longer selects 7th gear at very high driving speeds.
However, if necessary, the gear can be selected manually.
Upshifts and downshifts are avoided as far as possible when PSM is active. In the case of high wheel slip when PSM is switched off, upshifts are prevented until slip is no longer detected.
Driving in coasting mode
Through attentive driving, fuel can be saved in coasting mode. The vehicle rolls with the engine disengaged and at idle speed without engine braking effect.
Preconditions for automatic coasting mode – Driving in selector lever position D – Coasting mode is switched on.Indicator light on the button is off.– Sport and Sport Plus modes are switched off– PSM is active– Cruise control is not active– Engine, transmission and battery are at operating temperature– Calm/economic driving style– Slight uphill or slight downhill gradientsfSlowly take your foot off the accelerator.
The engine is disengaged and runs at idle speed. The vehicle rolls with no engine braking effect. Coasting mode is recognizable by the idle speed indicated on the tachometer.
Information
In the case of a sporty driving or when swiftly releasing the accelerator pedal, coasting mode is suppressed to allow targeted use of the engine braking effect. On more pronounced uphill gradients, “coasting” is also prevented as the coasting phases are very short due to the gradient and no significant fuel savings can be achieved. On more pronounced downhill gradients, coasting
14_991_Turbo_21.book Seite 174 Mittwoch, 9. April 2014 2:19 14

Driving and Driving Safety 175
is suppressed because here, the vehicle does not slow down, despite the engine overrun torque and no fuel is consumed in this driving situation due to utilization of the overrun shut-off.
Ending coasting mode/utilizing engine braking effect
fPress the accelerator or brake pedalor Operate a shift paddle or a shift button or Shift gear using the selector lever.
Initiating coasting mode manually
– Driving in selector lever position D or driving in selector lever position M
When coasting mode is suppressed, e.g. in the case of sporty driving, sudden release of the accelerator pedal or excessively low engine temperature, coasting mode can be initiated manually.fTake your foot off the accelerator pedal and shift past the highest possible gear with the shift paddle, one of the shift buttons, or with the selector lever.
Switching coasting mode on and off using the Auto Start Stop button
Switching off
fPress button . The indicator light on the button lights up.Coasting mode is switched off and automatic stopping of the engine is suppressed.
Switching on
fPress button . The indicator light on the button goes out.Coasting mode is switched on and the engine is automatically stopped when the vehicle stops.
“Sport” mode activated
The PDK transmission switches to a sporty gear- changing map and shortens the shifting times.A sporty driving style is recognized more quickly and the gear-changing speeds are adapted to driving performance.
Braking downshifts are initiated earlier. Downshifts occur for small decelerations, even at higher revs.
“Sport Plus” mode activated
In “Sport Plus” mode, the PDK transmission changes to a shift program designed for driving on race circuits. 7th gear is not selected.The gear-changing performance is enhanced significantly again compared with “Sport” mode.fPlease see the chapter ““SPORT” AND “SPORT PLUS” MODE” on page 188.
Driving off with Launch Control
Launch Control allows you to achieve maximum acceleration from standstill.
Launch Control is designed to be used in a controlled environment on closed circuit driving courses where no vehicle cross traffic or pedestrian traffic is present.fUse Launch Control only if conditions permit it to be applied in a safe manner.fDo not use Launch Control if there is a possibility it could endanger other persons.Such a possibility exists if you cannot see that you have a clear road with no possibility of cross traffic in your intended direction of driving.
Information
Stress on components increases dramatically when starting with maximum acceleration in comparison with normal driving off.
Preconditions: – Launch Control should only be used when the engine has reached operating temperature.–“ Sport Plus” mode must be switched on (indicator light on the button comes on and SPORT PLUS appears on the digital speedometer or on the steering wheel).1. Press the brake with your left foot. 2. Quickly press the accelerator down fully (kickdown activated) and hold it.The engine speed will level off at around 5,500 rpm.“ Launch Control activated” is displayed on the multi-function display.Depending on equipment, the “LAUNCH CONTROL” logo appears on the steering wheel.3. Release the brake within a few seconds.
Remaining stationary for a long time with LAUNCH CONTROL can lead to overloading of the transmission.To protect the transmission, the engine power is then reduced and the LAUNCH CONTROL process is cancelled.
In order to drive off, the accelerator must first be fully released.
Endangering Other Road Users
WARNINGh
14_991_Turbo_21.book Seite 175 Mittwoch, 9. April 2014 2:19 14

Driving and Driving Safety 177
Steering wheel with shift paddles
Shifting up with selector lever or right “+” shift paddle
fPress the PDK selector lever forward or pull the right shift paddle on the steering wheel back.
Shifting down with selector lever or left “–” shift paddle
fPull the PDK selector lever or left shift paddle on the steering wheel back.
Shift to N – Neutral using the shift paddles
fPull both shift paddles simultaneously and release them again immediately. Transmission in N – Neutral.
The vehicle rolls with the engine disengaged and at idle speed without engine braking effect. The number in the gear indicator goes out and the selector lever position flashes.
Power transmission can be re-established by pulling one of the shift paddles or by actuating the selector lever.
At low speeds approaching standstill, the brake must be actuated in order to establish power transmission.
Fast gear shifting by repeated operation of the selector lever, shift buttons or shift paddles.
You can shift up or down by the corresponding number of gears by quickly operating the selector lever, the shift buttons or the shift paddles several times in succession.
Gear changes that would exceed the upper or lower engine-speed limit are not executed by the control unit.
There is no automatic upshift at the upper engine- speed limit in selector-lever position M. Upshift suppression can be cancelled by kickdown operation. If, for example, the engine-speed limit is reached during overtaking and an automatic upshift does not occur, the transmission shifts up in this case as a result of kickdown operation.fSelect an appropriately low gear on upward and downward slopes.This will ensure optimum use of engine power and engine braking.
Upshift prompt for fuel-economy- optimized driving
The consumption-oriented upshift indicator A in the tachometer at the right beside the digital speed display helps you to develop a fuel-saving driving style.
The upshift indicator lights up – prompting you to shift up to the next-higher gear – depending on the selected gear, engine speed and accelerator pedal position.fChange to the next-higher gear when the upshift indicator lights up.
14_991_Turbo_21.book Seite 177 Mittwoch, 9. April 2014 2:19 14