2014 Peugeot RCZ Owner's Manual - RHD (UK, Australia)

2/
ACCESS
BOOT
OPENING
 Press this button for more than two seconds to unlock the boot lid. The boot lid opens slightly.
 Lift the boot lid.
This action also unlocks the doors and the fuel fi ller fl ap.
Using the manual control; vehicle unlocked
 Press the opening control above the number plate.
 Lift the boot lid.
CLOSING
 Lower the boot lid using one of the interior grab handles.
 If necessary, press the top of the boot lid to close it fully.
If the boot lid is not closed correctly: - when the engine is running , this warning lamp comes on, accompanied by a message in the screen for a few seconds,
When selective unlocking is activated, the boot can also be
opened by a second press on the open padlock on the remote
control.
Using the remote control
Emergency locking
If the central locking system fails (fl at battery), you are advised to
disconnect the battery. - when the vehicle is moving (speed above 6 mph (10 km/h)), this
warning lamp comes on, accompanied by an audible signal and a
message in the screen for a few seconds.
Never grasp the boot lid by the active spoiler.

64
FRONT SEATS
Seat with integral head restraint, consisting of a seat cushion and a se\
at
back which can be adjusted to adapt your position for ease of driving
and comfort.
MANUAL ADJUSTMENTS
Forwards-backwards adjustment Driver's or passenger's seat height adjustment
Seat back angle adjustment
 Raise the control bar and slide the seat forwards or backwards.  Pull the control lever upwards to raise or push it downwards to
lower, as many times as necessary, to obtain the position required.
 Turn the knob to set the angle required.
Before moving the seat backwards, ensure that there is nothing
that might prevent the full travel of the seat, so as to avoid the risk \
of of jamming the seat caused by the presence of objects on the
fl oor behind the seat or rear passengers. If the seat jams, stop the
movement immediately.

3/
EASE OF USE and COMFORT
FRONT SEATS
Seat with integral head restraint, consisting of a seat cushion and a se\
at
back which can be adjusted to adapt your position for ease of driving
and comfort.
ELECTRIC ADJUSTMENTS
Forwards-backwards adjustment Seat cushion height adjustment
 Push the control forwards or rearwards to slide the seat.  Tilt the rear part of the control upwards or downwards to obtain the
required height.
The electrical functions of the seat are deactivated approximately
one minute after the ignition is switched off.
To reactivate them, switch on the ignition.
Carry out these adjustments with the engine running to avoid
discharging the battery.
Seat back angle adjustment
 Tilt the control forwards or rearwards to adjust the angle of the seat
back.
Before moving the seat backwards, ensure that there is nothing
that might prevent the full travel of the seat, so as to avoid the risk \
of of jamming the seat caused by the presence of objects on the
fl oor behind the seat or rear passengers. If the seat jams, stop the
movement immediately.

66
MANUAL LUMBAR ADJUSTMENT
 Turn the knob manually to obtain the desired level of lumbar support.
Heated seats control
With the engine running, the front seats can be heated separately.
 Use the adjustment dial, placed on the side of each front seat, to switch on and select the level of heating required:
0 : Off.
1 : Low.
2 : Medium.
3 : High.

3/
EASE OF USE and COMFORT
STORING DRIVING POSITIONS
System which takes into account the electrical settings of the driver's \
seat and the door mirrors. It enables you to store two positions using
the buttons on the side of the driver's seat.
STORING A POSITION
Using buttons M / 1 / 2
 Switch on the ignition.
 Adjust your seat and your door mirrors.
 Press button M , then press button 1 or 2 within four seconds.
An audible signal is heard indicating that the settings have been stored.
RECALLING A STORED POSITION
Storing a new position cancels the previous position.
Using button 1 or 2
 Press and hold button 1 or 2 until the audible signal is heard
indicating the end of the adjustment.
When the ignition is off, after a few consecutive position recalls,
the function will be deactivated until the engine is started, to
prevent discharging of the battery.

68
STEERING WHEEL ADJUSTMENT
 When stationary , pull the control lever to release the adjustment mechanism.
 Adjust the height and reach to suit your driving position.
 Push the control lever to lock the adjustment mechanism.
As a safety precaution, these operations should only be carried
out with the vehicle stationary.

3/
EASE OF USE and COMFORT
MIRRORS
DOOR MIRRORS
Each fi tted with an adjustable mirror glass permitting the lateral
rearward vision necessary for overtaking or parking. They can be
folded electrically.
Demisting - defrosting
The demisting-defrosting of the door mirrors is effected with
the engine running, by switching on the heated rear screen
(refer to the "Demisting-defrosting the rear screen" section).
Adjustment
 Move control A to the right or to the left to select the corresponding
mirror.
 Move control B in all four directions to adjust.
 Return control A to the central position.
The objects observed are, in reality, closer than they appear.
Take this into account in order to correctly judge the distance of
vehicles approaching from behind.

70
Folding
 From outside: lock the vehicle using the remote control or the key.
 From inside: with the ignition on, pull the control A in the central
position rearwards.
If the mirrors are folded using control A , they will not unfold when
the vehicle is unlocked. Pull again on control A .
Unfolding
 From outside: unlock the vehicle using the remote control or the
key.
 From inside: with the ignition on, pull the control A in the central
position rearwards.
The folding and unfolding of the door mirrors using the remote
control can be deactivated by a PEUGEOT dealer or a qualifi ed
workshop.
If necessary the mirrors can be folded manually.
Automatic tilting in reverse gear
System which provides a view of the ground during parking
manoeuvres in reverse gear.
Programming
 With the engine running, engage reverse gear.
 Select and adjust the left-hand and right-hand mirrors in succession.
The adjustment is stored immediately.
Switching on
 With the engine running, engage reverse gear.
 Move control A to the right or to the left to select the corresponding
mirror.
The glass of the mirror selected tilts downwards, in accordance with its\

programming.
Switching off
 Exit reverse gear and wait ten seconds.
or
 Return control A to the central position.
The mirror glass returns to its initial position.
The mirror glass also returns to its initial position:
- if the speed exceeds 6 mph (10 km/h),
- if the engine is switched off.