2014 NISSAN TEANA warning

SE-52
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
8. Remove and discard the two side air bag module nuts (A).(1) Side air bag module
CAUTION:
Do not reuse the side air bag module nuts.
9. Disengage the side air bag module studs from the s eatback frame and lift the seatback cushion trim and
seatback pad as an assembly to remove from the seatback frame.
10. Open the seatback cushion and release the side air bag module studs (A) protruding through holes in the chute (B).
11. Pull the side air bag module (1) out of the chute (B) and remove from the seatback trim.
CAUTION:
• Replace the front passenger air bag module if it has been dropped or sustained an impact.
• Do not strike the front passenger air bag module.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Inspect seatback pad, seatback trim and seatback trim chutes. Replace if damaged.
• Smooth out all wrin kles during assembly.
• Always route side air bag module harness in original location. Replace any deformed or damaged
clips with same type and color. Always install clips in the original location in the harness.
• After installation is completed, check that no system malfunction is detected causing the air bag
warning lamp to illuminate.
• If a malfunction is detected by the air bag warnin g lamp after repair or replacement of the malfunc-
tion parts, perform the SRS final check. Refer to SRC-17, "SRS Final Check"
.
ALJIA0935ZZ
ALJIA0808ZZ
JMHIA0009ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

FRONT SEATSE-55
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
PASSENGER SIDE : Disassembly and AssemblyINFOID:0000000009462952
SEATBACK ASSEMBLY
WARNING:
Do not leave any objects (screwdri vers, tools, etc.) on the seat during seatback repair. It can lead to
personal injury if the side air bag should accidentally deploy.
CAUTION:
• Before servicing, turn ignition swit ch OFF, disconnect both battery terminals and wait at least three
minutes.
• Handle the side air bag module carefully. During disassembly, always hold the side air bag module,
do not let it hang by the wire harness.
• Always work from the side or back of the seat back assembly, do not work in front of seat.
• Do not use air tools or electric tools for servicing the seat assembly.
• Replace the side air bag module if it h as been dropped or sustained an impact.
• Do not insert any objects into the side air bag module.
• Do not attempt to disassemble the side air bag module.
• Do not expose the side air bag module to temperatures exceeding 93 °C (200 °F).
• Do not expose the side air bag module to any oil, grease, detergent or water.
• During disassembly, do not damage the seatback board , chutes, connectors, retainers, clips, module
harness or the side air bag module.
NOTE:
If the vehicle has been involved in a collision and the side air bag has deployed, the front seatback assembly
must be replaced.
Disassembly
1. Remove the front seat assembly. Refer to SE-30, "PASSENGER SIDE : Removal and Installation - Seat
Assembly".
2. Remove the seatback board. Refer to SE-31, "PASSENGER SIDE : Removal and Installation - Seatback
Board".
10. Front slide cover (RH) 11. Front slide cover (LH) 12. Seat frame assembly
13. Occupant classification control unit 14. Seat harness 15. Seat belt buckle with switch
16. Seat belt buckle without switch 17. Seat cushion outer finisher (LH) 18. Seat cushion inner finisher (LH rear)
19. Seat cushion inner finisher (LH front) 20. Rear slide cover (LH) 21. Rear hinge cover
22. Headrest holder (locked) 23. Headrest holder (free) 24. Seatback assembly
25. Headrest 26. Seatback board A. Side air bag module nuts
B. Rear hinge cover clips C. Seatback board clips
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

SE-58
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
a. Open the seatback trim and release the side air bag modulestuds (A) protruding through holes in the chute (B).
b. Pull the side air bag module (1) out of the chute (B) and remove from the seatback trim.
c. Pull the seatback trim (1) upward from bottom to release hook fasteners (A).
d. Remove three hog rings and separate the seatback trim from the seatback pad.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.
CAUTION:
• Inspect seatback pad, seatback trim and seatback trim chutes. Replace if damaged.
• Smooth out all wrin kles during assembly.
• Always route side air bag module harness in original location. Replace any deformed or damaged
clips with same type and color. Always install clips in the original location in the harness.
• After work is completed, check that no system ma lfunction is detected causing the air bag warning
lamp to illuminate.
• If a malfunction is detected by the air bag warnin g lamp after repair or replacement of the malfunc-
tion parts, perform the SRS final check. Refer to SRC-17, "SRS Final Check"
.
• When installing the side air bag module, make sure the side air bag chute (4) is pulled over the out board surface of the side air bag
module (3). Make sure there are no wrinkles and the chute is not
folded, twisted or pinched.
(1) Seatback pad
(2) Frame
(5) Seatback board
: Front
CAUTION:
• Do not reuse side air bag module nuts.
• Make sure the side air bag mo dule nuts are tightened to
specification. Refer to SE-54, "PASSENGER SIDE : Exploded
View".
AWJIA0900ZZ
AWJIA0899ZZ
ALJIA0682ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

FRONT SEATSE-59
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
• When installing the seatback trim, firmly push down while sliding your hand along the seams as shown ( ) to ensure the hook fas-
teners below the seatback trim are fastened properly.
• Install new hog rings on the seatback trim in original positions. Use only one hog ring in each designated location.
Ensure hog rings are correctly fastened around both the seatback
trim and seatback pad wires.
Use NISSAN standard hog rings and tools to assemble.
• Install all seatback assembly bolts and tighten evenly in sequence shown.
Tighten the seatback assembly bolts to specification. Refer to SE-
54, "PASSENGER SIDE : Exploded View".
SEAT CUSHION
WARNING:
Do not leave any objects (screwdrivers, tools, etc. ) on the seat during seat cushion repair. It can lead
to personal injury if the side air bag should accidentally deploy.
CAUTION:
• Before servicing, turn ignition swit ch OFF, disconnect both battery terminals and wait at least three
minutes.
• Always work from the side or back of the seat back assembly, do not work in front of seat.
• Do not use air tools or electric tools for servicing the seat assembly.
• During disassembly, do not damage the seatback cover , chutes, connectors, retainers, clips, module
harness or the side air bag module.
Disassembly
1. Remove the front seat assembly. Refer to SE-30, "PASSENGER SIDE : Removal and Installation - Seat
Assembly".
2. Remove the seatback board. Refer to SE-31, "PASSENGER SIDE : Removal and Installation - Seatback
Board".
3. Remove the rear hinge cover.
ALJIA0656ZZ
PIIB3356J
ALJIA0968ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

FRONT SEATSE-61
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D E
F
G H
I
K L
M A
B
SE
N
O P
7. Remove the seat cushion trim (1) and seat cushion pad as an assembly.
:Front
a. Release J-clips (A) holding the seat cushion trim to the seat frame assembly.
b. Release J-clip (B) holding the seat cushion trim to the seat frame assembly.
c. Release J-clips (D) holding the seat cushion trim to the seat frame assembly.
d. Release retainer strips (C) holding the seat cushion trim to the seat frame assembly.
e. Disconnect the harness connector from the seat cushion heater (if equipped).
NOTE:
Take note of harness routing and attachment location for accu-
rate installation.
8. Remove the seat cushion trim (1) and the seat cushion pad from the seat frame assembly.
9. Separate the seat cushion trim (1) from the seat cushion pad.
a. Pull the seat cushion trim upward to release hook fasteners (A).
b. Remove three hog rings and separate the seat cushion trim from the seat cushion pad.
: Hog ring
NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.
CAUTION:
• Smooth out all wrinkles during assembly.
• Always route side air bag module harness in origin al location. Replace any deformed or damaged
clips with same type and color. Always install cl ips in the original location in the harness.
• After work is completed, check that no system ma lfunction is detected causing the air bag warning
lamp to illuminate.
• If a malfunction is detected by the air bag warni ng lamp after repair or replacement of the malfunc-
tion parts, perform the SRS final check. Refer to SRC-17, "SRS Final Check"
.
ALJIA0954ZZ
ALJIA0965ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

SE-62
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
• When installing the seat cushion trim, firmly push down while slid-ing your hand along the seams as shown ( ) to ensure the hook
fasteners below the seat cushion trim are fastened properly.
• Install new hog rings on the seat cushion trim in original positions. Use only one hog ring in each designated location.
Ensure hog rings are correctly fastened around both the seat cush-
ion trim and seat cushion pad wires.
Use NISSAN standard hog rings and tools to assemble.
PASSENGER SIDE : Side air bag moduleINFOID:0000000009462953
WARNING:
Do not leave any objects (screwdrivers, tools, etc. ) on the seat during seatback repair. It can lead to
personal injury if the side ai r bag should accidentally deploy.
CAUTION:
• Before servicing, turn ignition sw itch OFF, disconnect both battery terminals and wait at least three
minutes.
• Handle the side air bag module carefully. During disassembly, alw ays hold the side air bag module,
do not let it hang by the wire harness.
• Always work from the side or back of the seat back assembly, do not work in front of seat.
• Do not use air tools or electric tools for servicing the seat assembly.
• Replace the side air bag module if it h as been dropped or sustained an impact.
• Do not insert any objects into the side air bag module.
• Do not attempt to disassemble the side air bag module.
• Do not expose the side air bag module to temperatures exceeding 93 °C (200 °F).
• Do not expose the side air bag module to any oil, grease, detergent or water.
• During disassembly, do not damage the seatback board, chutes, connectors, retainers, clips, module
harness or the side air bag module.
NOTE:
• If the vehicle has been involved in a collision and the side air bag has deployed, the front seatback assembly
must be replaced.
• For side air bag module removal and installation, seatback trim and seatback pad must be removed.
REMOVAL
1. Remove the front seat assembly. Refer to SE-30, "PASSENGER SIDE : Removal and Installation - Seat
Assembly".
2. Remove the seatback board. Refer to SE-31, "PASSENGER SIDE : Removal and Installation - Seatback
Board".
ALJIA0656ZZ
PIIB3356J
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

SE-64
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
9. Disengage the side air bag module studs from the seatback frame and lift the seatback cushion trim and
seatback pad as an assembly to remove from the seatback frame.
10. Open the seatback cushion and release the side air bag module studs (A) protruding through holes in the chute (B).
11. Pull the side air bag module (1) out of the chute (B) and remove from the seatback trim.
CAUTION:
• Replace the front passenger air bag module if it has been
dropped or sustained an impact.
• Do not strike the front passenger air bag module.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Inspect seatback pad, seatback trim and seatback trim chutes. Replace if damaged.
• Smooth out all wrin kles during assembly.
• Always route side air bag module harness in original location. Replace any deformed or damaged
clips with same type and color. Always install clips in the original location in the harness.
• After installation is completed, check that no system malfunction is detected causing the air bag
warning lamp to illuminate.
• If a malfunction is detected by the air bag warnin g lamp after repair or replacement of the malfunc-
tion parts, perform the SRS final check. Refer to SRC-17, "SRS Final Check"
.
AWJIA0900ZZ
JMHIA0009ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

SEC-4
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009951563
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISS AN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for WorkINFOID:0000000009461062
• When removing or disassembling each component, be careful not to damage or deform it. If a component may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a s hop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM