2014 NISSAN TEANA engine

PRECAUTIONSEC-17
< PRECAUTION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
•
After performing each TROUBL E DIAGNOSIS, perform DTC
CONFIRMATION PROCEDURE or Component Function
Check. The DTC should not be displayed in the DTC Confir-
mation Procedure if the repair is completed. The Component
Function Check should be a good result if the repair is com-
pleted.
• When measuring ECM signals with a circuit tester, never allow
the two tester probes to contact.
Accidental contact of probes will cause a short circuit and
damage the ECM power transistor.
• Do not operate fuel pump when there is no fuel in lines.
• Tighten fuel hose clamps to the specified torque.
• Do not depress accelerator pedal when starting.
• Immediately after starting, do not rev up engine unnecessar-
ily.
• Do not rev up engine ju st prior to shutdown.
JSBIA1315ZZ
SEF348N
SEF709Y
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-20
< PREPARATION >[QR25DE]
PREPARATION
Socket wrench Removes and installs engine coolant temperature
sensor
Oxygen sensor thread
cleaner
i.e.: (J-43897-18)
(J-43897-12) Reconditions the exhaust system threads before
installing a new oxygen sensor. Use with anti-
seize lubricant shown below.
a: 18 mm diameter with pitch 1.5 mm for Zirco-
nia Oxygen Sensor
b: 12 mm diameter with pitch 1.25 mm for Tita-
nia Oxygen Sensor
Anti-seize lubricant
i.e.: (Permatex
TM
133AR or equivalent
meeting MIL specifica-
tion MIL-A-907) Lubricates oxygen sensor thread cleaning tool
when reconditioning exhaust system threads.
Tool name
(TechMate No.) Description
S-NT705
AEM488
S-NT779
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

COMPONENT PARTSEC-21
< SYSTEM DESCRIPTION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts LocationINFOID:0000000009462053
ENGINE ROOM COMPARTMENT
ALBIA0804ZZ
No. Component Function
EVAP canister purge volume control solenoid valve EC-34, "EVAP Canister Purge Volume Control Solenoid
Va l v e "
Transmission range switch• The transmission range switch is installed to upper part
of transaxle case.
• ECM detects the selector lever position because the continuity of the transmission range switch line (the
ON) exists.
ECM EC-25, "ECM"
Refrigerant pressure sensorEC-36, "Refrigerant Pressure Sensor"
Battery current sensor
(with battery temperature sensor) EC-35, "Battery Current Se
nsor (With Battery Tempera-
ture Sensor)"
IPDM E/R • IPDM E/R control the internal relays and the actuators.
-Refer to PCS-6, "RELAY CONTROL SYSTEM : Sys-tem Description".
• When CAN communication with ECM is impossible,
IPDM E/R performs fail-safe control.
-Refer to PCS-19, "Fail Safe"
.
Mass air flow sensor
(with intake air temperature sensor) EC-27, "Mass Air Flow Sensor (With Intake Air Tempera-
ture Sensor)"
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-22
< SYSTEM DESCRIPTION >[QR25DE]
COMPONENT PARTS
ENGINE COMPARTMENT
Intake manifold runner control valve actuator
EC-31, "Intake Manifold Runner Control Valve"
Electric throttle control actuator
(with built in throttle position sensor and throttle control motor) EC-25, "Electric Thrott
le Control Actuator"
EVAP service port When perform the EVAP leak check, positive pressure is
delivered to the EVAP system through the EVAP service
port.
Refer to EC-537, "Inspection"
.
No. Component Function
JPBIA5840ZZ
Engine rear side Intake side
: Vehicle front
No. Component Function
Exhaust valve timing control position sensor EC-30, "Exhaust Valve Timing Control Position Sensor"
Camshaft position sensor (PHASE)EC-29, "Camshaft Position Sensor (PHASE)"
PCV valveThe positive crankcase ventilation (PCV) valve is provided
to conduct crankcase blow-by gas to the intake manifold.
Fuel injector EC-26, "Fuel Injector"
Crankshaft position sensor (POS)EC-29, "Crankshaft Position Sensor (POS)"
Knock sensorEC-33, "Knock Sensor"
Engine oil temperature sensorEC-33, "Engine Oil Temperature Sensor"
Engine oil pressure sensorEC-33, "Engine Oil Pressure Sensor"
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

COMPONENT PARTSEC-23
< SYSTEM DESCRIPTION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
EXHAUST COMPARTMENT
BODY COMPARTMENT
Intake valve timing intermediate lock control solenoid valve
EC-30, "Intake Valve Timing Intermediate Lock Control So-lenoid Valve"
Intake valve timing control solenoid valve
EC-30, "Intake Valve Timing Control Solenoid Valve"
Exhaust valve timing control solenoid valveEC-31, "Exhaust Valve Timing Control Solenoid Valve"
Ignition coil (with power transistor)EC-26, "Ignition Coil With Power Transistor"
Engine coolant temperature sensorEC-28, "Engine Coolant Temperature Sensor"
Intake manifold tuning valveEC-31, "Intake Manifold Tuning Valve"
Intake manifold runner control valve position sensor
EC-31, "Intake Manifold Runner Control Valve"
Intake manifold runner control valve actuator
No. Component Function
To engine assembly
JPBIA5841ZZ
No. Component Function
Air fuel ratio (A/F) sensor 1 EC-32, "Air Fuel Ratio (A/F) Sensor 1"
Heated oxygen sensor 2EC-32, "Heated Oxygen Sensor 2"
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

COMPONENT PARTSEC-25
< SYSTEM DESCRIPTION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
ECMINFOID:0000000009462054
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM controls the engine.
Accelerator Pedal Position SensorINFOID:0000000009462055
The accelerator pedal position sensor is installed on the upper end
of the accelerator pedal assembly. The sensor detects the accelera-
tor position and sends a signal to the ECM.
Accelerator pedal position sensor has two sensors. These sensors
are a kind of potentiometers which transform the accelerator pedal
position into output voltage, and emit the voltage signal to the ECM.
In addition, these sensors detect the opening and closing speed of
the accelerator pedal and feed the voltage signals to the ECM. The
ECM judges the current opening angle of the accelerator pedal from
these signals and controls the throttle control motor based on these
signals.
Idle position of the accelerato r pedal is determined by the ECM
receiving the signal from the acce lerator pedal position sensor. The
ECM uses this signal for the engine operation such as fuel cut.
Electric Throttle Control ActuatorINFOID:0000000009462056
Electric throttle control actuator cons ists of throttle body, throttle valve, throttle control motor and throttle posi-
tion sensor.
JPBIA5843ZZ
JPBIA5844ZZ
PBIB1741E
JSBIA0270GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-26
< SYSTEM DESCRIPTION >[QR25DE]
COMPONENT PARTS
THROTTLE CONTROL MOTOR RELAY
Power supply for the throttle control motor is provided to
the ECM via throttle control motor relay. The throttle
control motor relay is ON/OFF controlled by the ECM. When the ignition switch is turned ON, the ECM sends
an ON signal to throttle control motor relay and battery voltage is provided to the ECM. When the ignition
switch is turned OFF, the ECM sends an OFF signal to throttle control motor relay and battery voltage is not
provided to the ECM.
THROTTLE CONTROL MOTOR
The throttle control motor is operated by the ECM and it opens and closes the throttle valve.
The current opening angle of the throttle valve is detected by the throttle position sensor and it provides feed-
back to the ECM to control the throttle control mo tor to make the throttle valve opening angle properly in
response to driving condition.
THROTTLE POSITION SENSOR
The throttle position sensor responds to the throttle valve movement.
The throttle position sensor has two sensors. These sensors are a
kind of potentiometers which transform the throttle valve position into
output voltage, and emit the voltage signal to the ECM. In addition,
these sensors detect the opening and closing speed of the throttle
valve and feed the voltage signals to the ECM. The ECM judges the
current opening angle of the throttle valve from these signals and the
ECM controls the throttle control motor to make the throttle valve
opening angle properly in response to driving condition.
Ignition Coil With Power TransistorINFOID:0000000009462057
The ignition signal from the ECM is sent to and amplified by the
power transistor. The power transistor turns ON and OFF the ignition
coil primary circuit. This ON/OFF operation induces the proper high
voltage in the coil secondary circuit.
Fuel InjectorINFOID:0000000009462058
The fuel injector is a small, precise solenoid valve. When the ECM
supplies a ground to the fuel injector circuit, the coil in the fuel injec-
tor is energized. The energized coil pulls the ball valve back and
allows fuel to flow through the fuel injector into the intake manifold.
The amount of fuel injected depends upon the injection pulse dura-
tion. Pulse duration is the length of time the fuel injector remains
open. The ECM controls the injection pulse duration based on
engine fuel needs.
Fuel Level Sensor Unit and Fuel PumpINFOID:0000000009462059
FUEL PUMP
PBIB0145E
JPBIA4613ZZ
JPBIA5845ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

COMPONENT PARTSEC-27
< SYSTEM DESCRIPTION > [QR25DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
The ECM activates the fuel pump for 1 second after the ignition
switch is turned ON to improve engine start ability. If the ECM
receives a engine speed signal from the camshaft position sensor
(PHASE), it knows that the engine is rotating, and causes the pump
to operate. If the engine speed signal is not received when the igni-
tion switch is ON, the engine stalls. The ECM stops pump operation
and prevents battery discharging, thereby improving safety. The
ECM does not directly drive the fuel pump. It sends the control signal
to the fuel pump control module, which in turn controls the fuel
pump.
FUEL LEVEL SENSOR
The fuel level sensor is mounted in the fuel level sensor unit.
The sensor detects a fuel level in the fuel tank and tr ansmits a signal to the combination meter. The combina-
tion meter sends the fuel level sensor signal to the ECM via the CAN communication line.
It consists of two parts, one is mechanical float and the ot her is variable resistor. Fuel level sensor output volt-
age changes depending on the movement of the fuel mechanical float.
Fuel Tank Temperature SensorINFOID:0000000009462060
The fuel tank temperature sensor is used to detect the fuel tempera-
ture inside the fuel tank. The sensor modifies a voltage signal from
the ECM. The modified signal returns to the ECM as the fuel temper-
ature input. The sensor uses a ther mistor which is sensitive to the
change in temperature. The electrical resistance of the thermistor
decreases as temperature increases.

*: These data are reference values and are measured between ECM terminals.
Mass Air Flow Sensor (With Intake Air Temperature Sensor)INFOID:0000000009462061
MASS AIR FLOW SENSOR
JPBIA5842ZZ
Condition Fuel pump operation
Ignition switch is turned to ON. Operates for 1 second.
Engine running and cranking Operates.
When engine is stopped Stops in 1.5 seconds.
Except as shown above Sto ps .
SEF012P
Fluid temperature
[° C ( °F)] Voltage* (V) Resistance (k
Ω)
20 (68) 3.5 2.3 - 2.7
50 (122) 2.2 0.79 - 0.90
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM