2014 NISSAN TEANA engine

TM-368
< DTC/CIRCUIT DIAGNOSIS >[CVT: RE0F10E]
SHIFT POSITION INDICATOR CIRCUIT
SHIFT POSITION INDICATOR CIRCUIT
Component Parts Fu
nction InspectionINFOID:0000000009464323
1.CHECK SHIFT POSITION INDICATOR
1. Start the engine.
2. Shift selector lever.
3. Check that the selector lever position and the shift position indicator on the combination meter are identi-
cal.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Go to TM-368, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009464324
1.CHECK TCM INPUT/OUTPUT SIGNAL
With CONSULT
1. Start the engine.
2. Select “Data Monitor” in “TRANSMISSION”.
3. Select “RANGE”.
4. Shift selector lever.
5. Check that selector lever position, “RANGE” on CO NSULT screen, and shift position indicator display on
combination meter are identical.
Is the check result normal?
YES >> INSPECTION END
NO-1 (“RANGE” is changed but is not displayed on shif t position indicator.>>Check “Self Diagnostic Result”
in “TRANSMISSION”.
NO-2 (“RANGE” and shift position indicator are differ ent.)>>Check “Self Diagnostic Result” in “TRANSMIS-
SION”.
NO-3 (Specific“RANGE” is not displayed on shift pos ition indicator.)>>Check “Self Diagnostic Result” in
“METER/M&A”.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

CVT CONTROL SYSTEMTM-373
< SYMPTOM DIAGNOSIS > [CVT: RE0F10E]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
SYMPTOM DIAGNOSIS
CVT CONTROL SYSTEM
Symptom TableINFOID:0000000009464330
• The diagnosis item number indicates the order of check. Start checking in the order from 1.
• Perform diagnoses of symptom table 1 before symptom table 2.
Symptom Table 1
Symptom
Engine system
CAN communication line (U1000)
Transmission range switch (P0705, P0706)
Input speed sensor (P0717)
Primary speed sensor (P0715)
Output speed sensor (P2765)
CVT fluid temperature sensor (P0711, P0712, P0713)
Primary pressure sensor (P084C, P084D)
Secondary pressure sensor (P0841, P0847, P0848)
Torque converter clutch solenoid valve (P0740, P0743, P0744)
Stal l te st
CVT position
Power supply
Control valve
CVT fluid level and state
Ignition switch and starter
EC-630
TM-263
TM-288TM-289TM-366TM-387TM-286
PG-19
,
STR-6
Shift Shock Large shock (N
→ D position) 1 4 7 3 6 2 8 5
Large shock (N → R position) 1 4 7 3 6 2 8 5
Shock is too large for lock-up. 2 3 6 1 5 4
Slips/Will Not
Engage Vehicle cannot be started from D po-
sition. 8 3 5 6 7 91011 4 212131
Vehicle cannot be started from R po-
sition. 8 3 5 6 7 91011 4 212131
Does not lock-up. 26834109111257 131
Does not hold lock-up condition. 26834109111257 131
Lock-up is not released. 2 6 3 4 5 7 8 1
With selector lever in D position, ac-
celeration is extremely poor. 345789121011 2613141
With selector lever in R position, ac-
celeration is extremely poor. 345789121011 2613141
Slips at lock-up. 26834109111257 131
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-374
< SYMPTOM DIAGNOSIS >[CVT: RE0F10E]
CVT CONTROL SYSTEM
OtherNo creep at all. 243789101112 5613141
Vehicle cannot run in any position. 8 256791011 3412131
With selector lever in D position,
driving is not possible. 8 256791011 3412131
With selector lever in R position,
driving is not possible. 8 256791011 3412131
Judder occurs during lock-up. 2 6 3 4 5 7 8 1
Strange noise in D position. 2 3 4 1
Strange noise in R position. 2 3 4 1
Strange noise in N position. 2 3 4 1
Vehicle does not decelerate by en-
gine brake. 73 456 2 81
Maximum speed low. 23 567 89114 101
With selector lever in P position, ve-
hicle does not enter parking condi-
tion or, with selector lever in another
position, parking condition is not
cancelled. 12
Vehicle runs with CVT in P position. 1 3 4 2
Vehicle runs with CVT in N position. 1 3 4 2
Engine stall. 26 34 8957 101
Engine stalls when selector lever
shifted N → D or R. 26 34 5 71
Engine speed does not return to
idle. 24 3 51
Engine does not start in N or P posi-
tion. 321
Engine starts in positions other than
N or P. 321
Symptom
Engine system
CAN communication line (U1000)
Transmission range switch (P0705, P0706)
Input speed sensor (P0717)
Primary speed sensor (P0715)
Output speed sensor (P2765)
CVT fluid temperature sensor (P0711, P0712, P0713)
Primary pressure sensor (P084C, P084D)
Secondary pressure sensor (P0841, P0847, P0848)
Torque converter clutch solenoid valve (P0740, P0743, P0744)
Stall te st
CVT position
Power supply
Control valve
CVT fluid level and state
Ignition switch and starter
EC-630
TM-263
TM-288TM-289TM-366TM-387TM-286
PG-19
,
STR-6
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-376
< SYMPTOM DIAGNOSIS >[CVT: RE0F10E]
CVT CONTROL SYSTEM
OtherNo creep at all. 1 6 2 4 5 3
Vehicle cannot run in all posi-
tions. 1 2453 6
With selector lever in D position,
driving is not possible. 12435
With selector lever in R position,
driving is not possible. 12435
Judder occurs during lock-up. 1
Strange noise in D position. 1 2 4 3 5
Strange noise in R position. 1 2 4 3
Strange noise in N position. 1 2 3
Maximum speed low. 1 5 2 4 3
With selector lever in P position,
vehicle does not enter parking
condition or, with selector lever in
another position, parking condi-
tion is not cancelled. 1
Vehicle runs with CVT in P posi-
tion. 21
Vehicle runs with CVT in N posi-
tion. 231
Engine stall. 1
Engine stalls when selector lever
shifted N → D or R. 1
When brake pedal is depressed
with ignition switch ON, selector-
lever cannot be shifted from P po-
sition to other position. 123
When brake pedal is not de-
pressed with ignition switch ON,
selector lever can be shifted from
P position to other position. 123
Symptom
Torque converter
Transmission range switch
Oil pump
Forward clutch
Reverse brake
Planetary gear
Bearings
Parking mechanism
Stop lamp switch
Shift lock solenoid
CVT shift selector
TM-410
TM-407BR-13TM-369TM-378
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-400
< REMOVAL AND INSTALLATION >[CVT: RE0F10E]
CVT OIL WARMER SYSTEM
CVT OIL WARMER SYSTEM
WATER HOSE
WATER HOSE : Exploded ViewINFOID:0000000009464359
WATER HOSE : Removal and InstallationINFOID:0000000009464360
REMOVAL
WARNING:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator. Wrap a thick clot h around the cap. Slowly turn it a quarter turn to
allow built-up pressure to escape. Carefully remove the cap by turning it all the way.
CAUTION:
Perform when the engine is cold.
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
1. Remove front under cover. Refer to EXT-28, "Removal and Installation"
.
Hose clamp CVT water hose A CVT oil warmer
CVT water hose B Heater thermostat CVT water hose C
Transaxle assembly
Water outlet
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JSDIA3630GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

CVT OIL WARMER SYSTEMTM-401
< REMOVAL AND INSTALLATION > [CVT: RE0F10E]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
2. Remove engine room cover. Refer to EM-28, "Removal and Installation".
3. Remove front air duct and air cleaner case assembly. Refer to EM-29, "Removal and Installation"
.
4. Release clip (A) and release hose clamps and remove CVT water hose A from water outlet.
CAUTION:
Do not reuse hose clamps.
5. Remove CVT heater thermostat bolt, release hose clamps then remove CVT heater thermostat and CVT
water hose C from water outlet.
CAUTION:
Do not reuse hose clamps.
6. Remove CVT water hose inlet and CVT water hose outlet from CVT oil warmer.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Do not reuse hose clamps.
• Insert CVT water hose according to dimension (A) described below.
• Install hose clamps (1) at the both ends of CVT water hose (2) with dimension (A) from the hose end.
• Hose clamp should not interfere with the bulge.
: Front
ALDIA0365ZZ
CVT water hose (1) Insert side tube (2) Dimension (A)
CVT water hose A Water outlet
End reaches the spool portion (B)
CVT oil warmer
CVT water hose B CVT oil warmer
Heater thermostat
CVT water hose C Heater thermostat
Water outlet
JSDIA1291ZZ
Dimension (A) : 5 – 7 mm (0.20 – 0.28 in)
SCIA8123E
CVT water hose Hose end Paint mark
Position of hose clamp*
CVT water hose AWater outlet side Facing to the front of the vehicle A
CVT oil warmer side Facing to the front of the vehicle C
CVT water hose B CVT oil warmer side Facing to the front of the vehicle B
Heater thermostat side N/A A
CVT water hose C Heater thermostat side N/A A
Water outlet side Facing upward C
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

TM-402
< REMOVAL AND INSTALLATION >[CVT: RE0F10E]
CVT OIL WARMER SYSTEM
*: Refer to the illustrations for the specific position of each hose clamp tab.
• The illustrations indicate the view from the hose ends.
• When installing hose clamps the center line of each clamp tab
should be positioned as shown.
WATER HOSE : InspectionINFOID:0000000009464361
INSPECTION AFTER INSTALLATION
Start and warm up the engine. Visually check that there is no leakage of engine coolant and CVT fluid.
CVT FLUID COOLER HOSE
CVT FLUID COOLER HOSE : Exploded ViewINFOID:0000000009464362
COMPONENT PARTS LOCATION
(D): Vehicle front
(E) : Vehicle upper
JSDIA1292ZZ
CVT oil warmer Hose clamp CVT fluid cooler hose A
CVT fluid cooler hose B Transaxle assembly
: To radiator
: Always replace after every disassembly.
JSDIA3631GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

CVT OIL WARMER SYSTEMTM-403
< REMOVAL AND INSTALLATION > [CVT: RE0F10E]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
CVT FLUID COOLER HOSE : Removal and InstallationINFOID:0000000009464363
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc. , cap or plug openings to prevent fluid from spill-
ing.
1. Remove front under cover. Refer to EXT-28, "Removal and Installation"
.
2. Remove engine room cover. Refer to EM-28, "Removal and Installation"
.
3. Remove the front air duct and air cleaner case assembly. Refer to EM-29, "Removal and Installation"
.
4. Release hose clamp, then remove CVT fluid cool er hose A and B from CVT oil warmer and radiator.
CAUTION:
Do not reuse hose clamps.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse hose clamps.
• Insert CVT fluid cooler hoses according to dimension (A).
• Install hose clamps (1) at both ends of CVT fluid cooler hoses (2) with dimension (A) from the hose end.
• Hose clamp should not interfere with the bulge.
*: Refer to the illustrations for the specific position of each hose clamp tab. CVT fluid cooler hose (1) Insert side tube (2) Dimension (A)
CVT fluid cooler hose A Radiator tube
End reaches the 2-stage
bulge (B)
CVT oil warmer
CVT fluid cooler hose B CVT oil warmer
Radiator tube
JSDIA1289ZZ
Dimension (A) : 5 – 7 mm (0.20 – 0.28 in)
SCIA8123E
CVT fluid cooler hose Hose end Paint mark Position of hose clamp*
CVT fluid cooler hose A Radiator tube side Facing upward B
CVT oil warmer side Facing to the right of the vehicle B
CVT fluid cooler hose B CVT oil warmer side Facing downward A
Radiator tube side Facing to the front of the vehi-
cle B
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM