2014 NISSAN TEANA door lock

DLK-60
< WIRING DIAGRAM >
POWER DOOR LOCK SYSTEM
ABKIA4811GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DOOR LOCK AND UNLOCK SWITCHDLK-103
< DTC/CIRCUIT DIAGNOSIS >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
DOOR LOCK AND UNLOCK SWITCH
DRIVER SIDE
DRIVER SIDE : DescriptionINFOID:0000000009461830
Transmits door lock/unlock operation to BCM.
DRIVER SIDE : Comp onent Function CheckINFOID:0000000009461831
1.CHECK FUNCTION
With CONSULT
Check CDL LOCK SW, CDL UNLOCK SW in Data Monitor mode with CONSULT.
Is the inspection result normal?
YES >> Door lock and unlock switch is OK.
NO >> With LH and RH anti-pinch, refer to DLK-103, "DRIVER SIDE : Diagnosis Procedure (With LH and
RH Anti-Pinch)".
NO >> With LH anti-pinch only, refer to DLK-104, "DRIVER SIDE : Diagnosis Procedure (With LH Anti-
Pinch Only)".
DRIVER SIDE : Diagnosis Procedure (With LH and RH Anti-Pinch)INFOID:0000000009461832
Regarding Wiring Diagram information, refer to DLK-51, "Wiring Diagram".
1.CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
1. Read voltage signal between BCM connector and ground with oscilloscope when door lock and unlock switch (driver side) is turned “LOCK” or “UNLOCK”.
2. Check that signals which are shown in the figure below can be detected during 10 second just after door lock and unlock switch (driver side) is turned “LOCK” or “UNLOCK”.
Is the inspection result normal?
YES >> GO TO 4
NO >> GO TO 2
2.CHECK POWER WINDOW SWITCH GROUND
1. Turn ignition switch OFF.
Monitor item Condition
CDL LOCK SW LOCK : ON
UNLOCK : OFF
CDL UNLOCK SW LOCK : OFF
UNLOCK : ON
Te r m i n a l Condition Signal
(Reference value)
(+)
(–)
BCM connector Terminal
M18 54 Ground Door is closed
PIIA1297E
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-104
< DTC/CIRCUIT DIAGNOSIS >
DOOR LOCK AND UNLOCK SWITCH
2. Disconnect main power window and door lock/unlock switch connector.
3. Check continuity between main power window and door lock/unlock switch connector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3.CHECK POWER WINDOW SERIAL LINK CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM connector and main power window and door lock/unlock switch connec-
tor.
3. Check continuity between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Repair or replace harness.
4.CHECK INTERMITTENT INCIDENT
Refer to GI-43, "Intermittent Incident"
.
>> Inspection End.
DRIVER SIDE : Diagnosis Procedur e (With LH Anti-Pinch Only)INFOID:0000000009461833
Regarding Wiring Diagram information, refer to DLK-51, "Wiring Diagram".
1.CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage at the main power window and door lock/unlock switch connector when the switch (driver side) is turned to “LOCK” or “UNLOCK”.
Is the inspection result normal?
YES >> GO TO 5
NO >> GO TO 2
2.CHECK POWER WINDOW SWITCH GROUND
Main power window and door
lock/unlock switch connector Terminal Continuity
D7 1 Ground Yes
BCM connector Terminal Main power window
and door lock/unlock
switch connector Terminal Continuity
M18 54 D7 11 Yes
BCM connector Terminals Continuity M18 54 Ground No
Connector Main power window and
door lock/unlock switch state Terminal Voltage
D12 Neutral
→ Unlock 15
Ground Battery voltage → 0
Neutral → Lock 3
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DOOR LOCK AND UNLOCK SWITCHDLK-105
< DTC/CIRCUIT DIAGNOSIS >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unlock switch connector.
3. Check continuity between main power window and door lock/unlock switch connector and ground.
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3.CHECK POWER WINDOW SWITCH
Check continuity between main power wi ndow and door lock/unlock switch terminals.
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-65, "Removal and Instal-
lation".
4.CHECK POWER WINDOW SWITCH CIRCUITS
1. Disconnect BCM connector.
2. Check continuity between BCM connector and main power window and door lock/unlock switch connec-
tor.
3. Check continuity between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 5
NO >> Repair or replace harness.
5.CHECK INTERMITTENT INCIDENT
Refer to GI-43, "Intermittent Incident"
.
>> Inspection End.
PASSENGER SIDE
PASSENGER SIDE : DescriptionINFOID:0000000009461834
Transmits door lock/unlock operation to BCM.
Main power window and door lock/unlock switch connector Terminal Continuity
D12 1 Ground Yes
Main power window and door lock/unlock switch state Terminals Continuity Lock 1 - 3 Ye s
Unlock 1 - 15
Neutral/Lock 1 - 15 No
Neutral/Unlock 1 - 3
BCM connector Terminal Main power window and
door lock/unlock switch connector Terminal Continuity
M17 34
D12 15
Ye s
19 3
BCM connector Terminal Continuity
M17 34
Ground No
19
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-106
< DTC/CIRCUIT DIAGNOSIS >
DOOR LOCK AND UNLOCK SWITCH
PASSENGER SIDE : Component Function Check
INFOID:0000000009461835
1.CHECK FUNCTION
With CONSULT
Check CDL LOCK SW, CDL UNLOCK SW in Data Monitor mode with CONSULT.
Is the inspection result normal?
YES >> Door lock and unlock switch is OK.
NO >> With LH and RH anti-pinch, refer to DLK-106, "PASSENGER SIDE : Diagnosis Procedure (With
LH and RH Anti-Pinch)".
NO >> With LH anti-pinch only, refer to DLK-107, "PASSENGER SIDE : Diagnosis Procedure (With LH
Anti-Pinch Only)".
PASSENGER SIDE : Diagnosis Procedure (With LH and RH Anti-Pinch)INFOID:0000000009461836
Regarding Wiring Diagram information, refer to DLK-51, "Wiring Diagram".
1.CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
1. Read voltage signal between BCM connector and ground with oscilloscope when power window and door lock/unlock switch RH is changed to “LOCK” or “UNLOCK”.
2. Check that signals which are shown in the figure below can be detected during 10 second just after power
window and door lock/unlock switch RH is changed “LOCK” or “UNLOCK”.
Is the inspection result normal?
YES >> GO TO 4
NO >> GO TO 2
2.CHECK POWER WINDOW SWITCH GROUND
1. Turn ignition switch OFF.
2. Disconnect power window and door lock/unlock switch RH connector.
3. Check continuity between power window and door lock/unlock switch RH connector and ground.
Monitor item Condition
CDL LOCK SW LOCK : ON
UNLOCK : OFF
CDL UNLOCK SW LOCK : OFF
UNLOCK : ON
Te r m i n a l
Condition Signal
(Reference value)
(+)
(–)
BCM
connector Te r m i n a l
M18 54 Ground Door is
closed
PIIA1297E
Power window and door lock/ unlock switch RH connector Terminal Continuity
D105 7 Ground Yes
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DOOR LOCK AND UNLOCK SWITCHDLK-107
< DTC/CIRCUIT DIAGNOSIS >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
Is the inspection result normal?
YES >> GO TO 3
NO >> Repair or replace harness.
3.CHECK POWER WINDOW SERIAL LINK CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM connector and power window and door lock/unlock switch RH connector.
3. Check continuity between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 4
NO >> Repair or replace harness.
4.CHECK INTERMITTENT INCIDENT
Refer to GI-43, "Intermittent Incident"
.
YES >> Inspection End.
PASSENGER SIDE : Diagnosis Proce dure (With LH Anti-Pinch Only)INFOID:0000000009461837
Regarding Wiring Diagram information, refer to DLK-51, "Wiring Diagram".
1.CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage at the power window and door lock/unl ock switch RH connector when the switch (passen-
ger side) is changed to “LOCK” or “UNLOCK”.
Is the inspection result normal?
YES >> GO TO 5
NO >> GO TO 2
2.CHECK POWER WINDOW SWITCH GROUND
1. Turn ignition switch OFF.
2. Disconnect power window and door lock/unlock switch RH connector.
3. Check continuity between power window and door lock/unlock switch RH connector and ground.
Is the inspection result normal?
BCM connector Terminal Power window and door
lock/unlock switch RH con- nector Terminal Continuity
M18 54 D105 3 Yes
BCM connector Terminals Continuity M18 54 Ground No
Connector Power window and
door lock/unlock switch RH state Terminal Voltage
D110 Neutral
→ Lock 1
Ground Battery voltage → 0
Neutral → Unlock 2
Power window and door lock/
unlock switch RH connector Terminal Continuity
D110 3 Ground Yes
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-108
< DTC/CIRCUIT DIAGNOSIS >
DOOR LOCK AND UNLOCK SWITCH
YES >> GO TO 3
NO >> Repair or replace harness.
3.CHECK POWER WINDOW SWITCH
Check continuity between power window and door lock/unlock switch RH terminals.
Is the inspection result normal?
YES >> GO TO 4
NO >> Replace power window and door lock/unlock switch RH.
4.CHECK POWER WINDO W SWITCH CIRCUITS
1. Disconnect BCM connector.
2. Check continuity between BCM connector and power window and door lock/unlock switch RH connector.
3. Check continuity between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 5
NO >> Repair or replace harness.
5.CHECK INTERMITTENT INCIDENT
Refer to GI-43, "Intermittent Incident"
.
>> Inspection End.
Power window and door lock/unlock switch RH state Terminals Continuity Lock 1 - 3 Ye s
Unlock 2 - 3
Neutral/Unlock 1 - 3 No
Neutral/Lock 2 - 3
BCM connector Terminal Power window and door
lock/unlock switch RH
connector Terminal Continuity
M17 19
D110 1
Ye s
34 2
BCM connector Terminal Continuity
M17 19
Ground No
34
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

OUTSIDE KEY ANTENNA (PASSENGER SIDE)DLK-109
< DTC/CIRCUIT DIAGNOSIS >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
OUTSIDE KEY ANTENN A (PASSENGER SIDE)
Component Function CheckINFOID:0000000009461838
1.CHECK OUTSIDE KEY ANTENNA (RH)
1. Place the Intelligent Key into the detection area of the outside key antenna (RH).
2. Press the door request switch (RH).
Does the door unlock?
YES >> Inspection End.
NO >> Refer to DLK-109, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009461839
Regarding Wiring Diagram information, refer to DLK-61, "Wiring Diagram".
1.CHECK OUTSIDE KEY ANTENNA INPUT SIGNAL 1
1. Turn ignition switch OFF.
2. Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-80, "Removal and Installation".
NO >> GO TO 2.
2.CHECK OUTSIDE KEY ANTENNA CIRCUIT
1. Disconnect BCM connector and outside key antenna (RH) connector.
2. Check continuity between BCM harness connector and outside key antenna (RH) harness connector.
3. Check continuity between BCM harness connector and ground.
(+)
(–) Condition Signal
(Reference value)
BCM
Connector Terminal
M20 114, 115 Ground When the driver door
request switch is op-
erated with ignition
switch OFF When Intelligent Key
is in the antenna de-
tection area (The dis-
tance between
Intelligent Key and
antenna: 80 cm or
less)
When Intelligent Key
is not in the antenna
detection area (The
distance between In-
telligent Key and an-
tenna: Approx. 2 m)
JMKIA5955GB
JMKIA5954GB
BCM Outside key antenna (RH) Continuity
Connector Terminal Connector Terminal
M20 11 4
D106 1
Ye s
11 5 2
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM