2014 NISSAN TEANA belt

EM-134
< PERIODIC MAINTENANCE >[VQ35DE]
DRIVE BELTS
DRIVE BELTS
Exploded ViewINFOID:0000000009460528
Checking Drive BeltsINFOID:0000000009460529
WARNING:
Inspect and check the drive belts with the engine off.
1. Inspect belt for cracks, fraying, wear or o il adhesion. If necessary, replace with a new one.
2. Rotate the crankshaft pulley two times then ensure t he drive belt auto-tensioner is within the possible use
range.
NOTE:
Inspect drive belt tension when engine is cold.
Tension AdjustmentINFOID:0000000009460530
Belt tension is not manually adjustable, it is aut omatically adjusted by the drive belt auto-tensioner.
Removal and InstallationINFOID:0000000009460531
REMOVAL
1. Remove the front RH wheel and tire. Refer to WT-55, "Adjustment".
2. Remove the fender protector side cover RH. Refer to EXT-26, "FENDER PROTECTOR : Removal and
Installation".
1. Drive belt auto-tensioner 2. Generator 3. A/C compressor
4. Drive belt 5. Crankshaft pulley A. Indicator
B. Range when new drive belt is installed C. Possible use range D. View D Engine front
AWBIA1225GB
Revision: November 20132014 Altima NAM

DRIVE BELTSEM-135
< PERIODIC MAINTENANCE > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
3. While securely holding the hexagonal part in pulley center of
drive belt auto-tensioner, move in the direction of arrow (loosen-
ing direction of drive belt auto-tensioner) using suitable tool.
WARNING:
Avoid placing hand in a locat ion where pinching may occur
if the holding tool accidentally comes off.
CAUTION:
Do not loosen the drive belt auto-tensioner pulley bolt. (do
not turn it counterclockwise. ) If turned counterclockwise,
the complete drive belt auto-t ensioner must be replaced as
a unit, including pulley.
4. Insert a rod approximately 6 mm (0.24 in) in diameter through the rear of drive belt auto-tensioner into retain ing boss to lock drive belt auto-tensioner pulley.
NOTE:
Leave drive belt auto-tensioner pulley arm locked until belt is installed again.
5. Loosen drive belt and then remove it from the other pulleys.
INSTALLATION
1. Install the drive belt onto all of the pulleys.
CAUTION:
Confirm belts are completely set on the pulleys.
2. Release drive belt auto-tensioner, and apply tension to belt. WARNING:
Avoid placing hand in a location wh ere pinching may occur if the holding tool accidentally comes
off.
CAUTION:
Do not loosen the auto-te nsioner pulley bolt. (Don't turn it counterclockwise. If turned counter-
clockwise, the complete auto-tensioner mu st be replaced as a unit, including pulley.
3. Turn crankshaft pulley clockwise several times to equalize tension between each pulley.
4. Confirm tension of belt at indicator is within the possible use range. Refer to EM-19, "Checking Drive
Belts".
5. Install the fender protector side cover RH. Refer to EXT-26, "FENDER PROTECTOR : Removal and
Installation".
6. Install the front RH wheel and tire. Refer to WT-55, "Adjustment"
.
Removal and Installation of Drive Belt Auto-tensionerINFOID:0000000009460532
AWBIA1204GB
Revision: November 20132014 Altima NAM

EM-136
< PERIODIC MAINTENANCE >[VQ35DE]
DRIVE BELTS
REMOVAL
CAUTION:
The complete auto-tensioner must be replaced as a unit, including the pulley.
1. Remove the drive belt EM-134, "Removal and Installation"
.
2. Remove the drive belt auto-tensioner using power tool.
CAUTION:
Do not loosen the drive belt auto-te nsioner pulley bolt. (Don't turn it counterclockwise. If turned coun-
terclockwise, the complete drive belt auto-tension er must be replaced as a unit, including pulley.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• If there is damage greater than peeled paint, replace drive belt auto-tensioner unit.
• Do not swap the pulley between the new an d old drive belt auto-tensioner unit.
1. Drive belt auto-tensioner
AWBIA1220GB
Revision: November 20132014 Altima NAM

EM-158
< REMOVAL AND INSTALLATION >[VQ35DE]
OIL PAN AND OIL STRAINER
1. Remove the engine from the vehicle. Refer to
EM-220, "Removal and Installation".
2. Drain the engine oil. Refer to LU-26, "Changing Engine Oil"
.
3. Remove the oil level gauge guide.
4. Remove the drive belt. Refer to EM-134, "Removal and Installation"
.
5. Disconnect the A/C compressor harness connector.
6. Remove the A/C compressor bolts and remove the A/C compressor. Refer to HA-30, "COMPRESSOR :
Removal and Installation".
7. Remove coolant pipe bolts. Refer to CO-51, "Removal and Installation"
.
8. Disconnect the coolant lines from the engine oil cooler.
9. Remove the oil filter and engine oil cooler from the upper oil pan.
10. Remove the oil pressure switch, and the cranks haft position sensor (POS) from the upper oil pan.
11. Remove the lower oil pan. Refer to EM-156, "Removal and Installation (Lower Oil Pan)"
.
12. Remove the upper oil pan.
a. Loosen the bolts in the order as shown, using power tool.
b. Insert an appropriate size tool into the notch (1) of the upper oil pan as shown.
c. Pry off the upper oil pan by moving the tool up and down (2) as shown.
13. Remove the O-ring seals from the bottom of the cylinder block and oil pump housing. Use new O-rings for installation.
CAUTION:
Do not reuse O-rings.
LBIA0358E
SEM155F
WBIA0327E
Revision: November 20132014 Altima NAM

FRONT TIMING CHAIN CASEEM-175
< REMOVAL AND INSTALLATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
NP
O
REMOVAL
1. Remove engine under cover. Refer to
EXT-28, "Removal and Installation".
2. Drain the engine coolant from the radiator. Refer to MA-23, "ENGINE COOLANT : Changing Engine Cool-
ant".
3. Drain the engine oil. Refer to MA-27, "ENGINE OIL : Changing Engine Oil"
.
4. Drain the power steering fluid. Refer to ST-30, "Draining and Refilling"
.
5. Remove engine room cover. Refer to EM-143, "Removal and Installation"
.
6. Remove front air duct. Refer to EM-144, "Removal and Installation"
.
7. Remove battery tray. Refer to PG-74, "Removal and Installation (Battery Tray)"
.
8. Remove the hood ledge covers (LH/RH).
9. Remove cowl top and cowl top extension. Refer to EXT-24, "Removal and Installation"
.
10. Remove upper radiator hose.
11. Disconnect engine coolant reservoir hose from t he radiator and remove engine coolant reservoir.
12. Remove cooling fan assembly. Refer to CO-42, "Removal and Installation"
.
13. Disconnect lower radiator hose from engine.
14. Remove the radiator. Refer to CO-41, "Removal and Installation"
.
15. Disconnect the power steering fluid reservoir tank hose from the power steering pump and fluid cooler and
remove the power steering fluid reservoir tank. Refer to ST-38, "Exploded View"
.
16. Remove the front RH wheel and tire. Refer to MA-39, "WHEELS : Adjustment"
.
17. Remove the fender protector side cover (RH). Refer to EXT-26, "FENDER PROTECTOR : Removal and
Installation".
18. Remove the drive belt. Refer to EM-134, "Removal and Installation"
.
19. Remove the rocker covers, if necessary. Refer to EM-168, "Removal and Installation LH"
and EM-169,
"Removal and Installation RH".
NOTE:
Necessary only when removing timing chains.
20. If removing the timing chains, obtain compression TDC of No. 1 cylinder as follows:
a. Rotate crankshaft pulley clockwise to align timing mark (grooved line without color) with timing indicator.
b. Check that intake and exhaust camshaft lobes on No. 1 cylinder (right bank of engine) are located as shown.
• If not, turn the crankshaft one revolution (360 °) and align as
shown.
21. Remove the access plate and lock the ring gear using Tool. CAUTION:
JMBIA1135GB
SEM418G
Tool number : — (J-50288)
Revision: November 20132014 Altima NAM

EM-176
< REMOVAL AND INSTALLATION >[VQ35DE]
FRONT TIMING CHAIN CASE
Do not damage the ring gear teeth, or the signal
plate teeth behind the ring gear, when installing
Tool.
22. Remove the crankshaft pulley as follows:
a. Loosen crankshaft pulley and locate bolt seating surfac e at 10 mm (0.39 in) from its original position.
b. Position a pulley puller at recess hole of crankshaft pulley to remove crankshaft pulley.
CAUTION:
Do not use a puller claw on crankshaft pulley periphery.
23. Remove the power steering pump. Refer to ST-38, "Removal and Installation"
.
24. Remove the lower oil pan. Refer to EM-156, "Removal and Installation (Lower Oil Pan)"
.
25. Remove upper oil pan bolts (1) and (2) as shown. Refer to EM-
157, "Removal and Installation (Upper Oil Pan)".
26. Remove the generator. Refer to CHG-32, "Removal and Installation"
.
27. Disconnect the A/C tubes from the A/C compressor and position aside. Refer to HA-23, "Recycle Refriger-
ant".
28. Remove the A/C compressor bolts and the A/C compressor. Refer to HA-30, "COMPRESSOR : Removal
and Installation".
29. Remove the generator bracket. Refer to CHG-32, "Removal and Installation"
.
30. Support the engine with suitable jack and remove the RH engine insulator, mount and torque rod. Refer to EM-220, "Removal and Installation"
.
31. Disconnect the oil pressure switch harness connector.
32. Disconnect the intake valve timing control solenoid valve harness connector.
33. Remove the intake valve timing control solenoid valve cover bank 1 (RH) (A) and intake timing control solenoid valve cover
bank 2 (LH) (B).
• Loosen the intake valve timing control solenoid valve cover bolts in the reverse order as shown.
CAUTION:
The shaft in the intake valve ti ming control solenoid valve
cover is inserted into the center hole of the intake cam-
shaft sprocket. Remove the in take valve timing control
solenoid valve cover by pull ing straight out until the
intake valve timing control so lenoid valve cover disengages from the camshaft sprocket.
34. Remove the drive belt auto-tensioner. Refer to EM-134, "Removal and Installation"
.
35. If necessary, remove the water pump cover.
EMQ0477D
WBIA0259E
(C) : Dowel pin hole
JPBIA1639ZZ
Revision: November 20132014 Altima NAM

EM-190
< REMOVAL AND INSTALLATION >[VQ35DE]
REAR TIMING CHAIN CASE
• Before removing the upper oil pan, re
move the crankshaft position sensor (POS).
• Be careful not to damage sensor edges.
• Do not spill engine oil or coolant on drive belt.
1. Remove the engine assembly. Refer to EM-220, "Removal and Installation"
.
2. Remove the oil pan lower and upper. Refer to EM-157, "Removal and Installation (Upper Oil Pan)"
.
3. Remove the front timing chain case. Refer to EM-174, "Removal and Installation"
.
4. Remove the primary and secondary timing chains. Refer to EM-182, "Removal and Installation"
.
5. Remove the rear timing chain case. CAUTION:
• Do not remove the plate metal cover for the oil passage.
• After removing the chain case, do not apply any load to
the case that might bend it.
a. Loosen and remove the rear timing chain case bolts in the order as shown.
b. Cut the sealant using Tool (A) and remove the rear timing chain case.
CAUTION:
• Be careful not to damage the mating surface.
• Do not insert a screwdriver or similar tool, this will dam-
age the mating surfaces.
c. In areas where the cutter is difficult to use, use a plastic hammer to lightly tap (1) the cutter where the liquid gasket is applied. Use
a plastic hammer to slide (2) the cutter by tapping on the side.
KBIA1307E
Tool number : KV10111100 (J-37228)
AWBIA0709ZZ
AWBIA1249GB
Revision: November 20132014 Altima NAM

EM-202
< REMOVAL AND INSTALLATION >[VQ35DE]
CAMSHAFT
• Using inside micrometer, measure diameter of valve lifter bore of
cylinder head. Refer to EM-247, "Camshaft"
EM-247, "Camshaft".
• If out of the specified range, replace the cylinder head assembly.
Calculation of Valve Lifter Clearance
• (Valve lifter clearance) = (hole diameter for valve li fter) – (outer diameter of valve lifter) Refer to EM-247,
"Camshaft".
• If out of specified range, replace either or both valve lifter and cylinder head assembly.
Inspection after InstallationINFOID:0000000009460570
INSPECTION OF CAMSHAFT SPROCKET (INT) OIL GROOVE
WARNING:
• Check when engine is cold so as to pr event burns from any splashing engine oil.
CAUTION:
• Perform this inspection only when DTC P0011 is detected in self-diagnostic results of CONSULT and
it is directed according to inspection procedure of EC section. Refer to EC-716, "Diagnosis Proce-
dure".
1. Check engine oil level. Refer to MA-26, "ENGINE OIL : Inspection"
.
2. Perform the following procedure so as to prevent the engine from being unintentionally started while
checking.
a. Release fuel pressure. Refer to FL-5, "Inspection"
.
b. Disconnect ignition coil and injector harness connectors if practical.
3. Remove intake valve timing control solenoid valve.
4. Crank engine, and then make sure that engine oil comes out from intake valve timing control solenoid valve cover oil hole.
End cranking after checking.
WARNING:
Be careful not to touch rotating parts (drive belts, idler pul-
ley, and crankshaft pulley, etc.).
CAUTION:
• Engine oil may squirt from intake valve timing control solenoid valve installation hole during cranking. Use a
shop cloth to prevent engi ne oil from splashing on
worker, engine components and vehicle.
• Do not allow engine oil to get on rubber components such
as drive belts or engine mount insulators. I mmediately wipe off any splashed engine oil.
5. Clean oil groove between oil strainer and intake valve timing control solenoid valve if engine oil does not come out from intake valve timing control solenoid valve cover oil hole.
6. Remove components between intake valve timing c ontrol solenoid valve and camshaft sprocket (INT),
and then check each oil groove for clogging.
• Clean oil groove if necessary.
7. After inspection, installation of the remaining components is in the reverse order of removal.
SEM867E
KBIA2686E
Revision: November 20132014 Altima NAM