2014 MERCEDES-BENZ CLS tow

There are several ways to deactivate
DISTRONIC PLUS:
XBriefly press the cruise control lever
forwards.
or
XBrake, unless the vehicle is stationary.
When you deactivate DISTRONIC PLUS, you
will see theDISTRONIC PLUS Offmessage
in the multifunction display for approximately
five seconds.
iThe last speed stored remains stored until
you switch off the engine.
iDISTRONIC PLUS is not deactivated if you
depress the accelerator pedal.
DISTRONIC PLUS is automatically
deactivated if:
Ryou engage the parking brake
Ryou are driving slower than 15 mph
(25 km/h) and there is no vehicle in front,
or if the vehicle in frontisnolonger
detected
RESP®intervenes or you deactivate ESP®
Rthe transmission is in theP,RorNposition
Ryou pull the cruise control lever towards
you in order to pull away and the front-
passenger door or one of the rear doors is
open
Rthe vehicle has skidded
Ryou activateActive Parking Assist
If DISTRONIC PLUS is deactivated, you will
hearawarning tone. You will see the
DISTRONIC PLUS Offmessage in the
multifunction display for approximately five
seconds.
Tips for driving with DISTRONIC PLUS
General notes
Pay particular attention in the following traffic
situations:
RCornering, going into and coming out of a
bend
RVehicles traveling onadifferent line
ROther vehicles changinglanes
RNarrow vehicles
RObstructions and stationary vehicles
RCrossing vehicles
In such situations, brake if necessary.
DISTRONIC PLUS is then deactivated.
Cornering, going into and coming out of a
bend
The ability of DISTRONIC PLUS to detect
vehicles when cornering is limited. Your
vehicle may brake unexpectedly or late.
Vehicles traveling onadifferent line
DISTRONIC PLUS may not detectvehicles
traveling onadifferent line. The distance to
the vehicle in frontwill be too short.
Driving systems185
Driving and parking
Z

Important safety notes
GWARNING
When leaving thevehicle, it can still rollaway
despitebeingbraked by theHOLD function if:
Rthere isamalfunction in the system or in
the voltage supply.
Rthe HOLD function has been deactivated by
pressing the accelerator pedal or the brake
pedal,e.g. byavehicle occupant.
Rthe electrical system in the engine
compartment,the battery or the fuses have
been tampered with.
Rthe battery is disconnected
There isarisk of an accident.
If you wish to exit the vehicle, always turn off
the HOLD function and secure the vehicle
against rolling away.
!If DISTRONIC PLUS or the HOLD function
is activated, the vehicle brakes
automaticallyincertain situations. To
prevent damage to the vehicle, deactivate
DISTRONIC PLUS and the HOLD function in
the following or other similarsituations:
Rwhen towingthe vehicle
Rin the car wash
Activation conditions
You can activatethe HOLDfunction if:
Rthe vehicle is stationary
Rthe engine is running or if it has been
automatically switched off by the ECO
start/stop function
Rthe driver's door is closed or your seat belt
is fastened
Rthe parking brakeisreleased
Rthe hood is closed
Rthe transmission is in positionD,RorN
RDISTRONIC PLUS is deactivated
Activating theHOLD function
XMake sure that the activation conditions
are met.
XDepress the brakepedal.
XQuickly depressthe brakepedal further
untilappears in the multifunction
display.
The HOLDfunction is activated. You can
release the brakepedal.
iIf depressing the brakepedal the first
timedoes not activatethe HOLDfunction,
wait briefly and thentry again.
Deactivatingthe HOLD function
The HOLD function is deactivated
automatically if:
Ryou accelerate and the transmission is in
positionDorR.
Ryou shift the transmission to positionP.
Ryou depress the brake pedalagain with a
certain amount of pressure until
disappears from the multifunction display.
Ryou activate DISTRONIC PLUS.
When the HOLD function is activated,the
transmission is shifted automatically to
positionPif:
Rthe driver's door is open and the driver's
seat beltisunfastened.
Rthe engine is switched off, unless it is
automaticallyswitched off by the ECO
start/stop function.
Rthe hood is opened.
Rasystem malfunction occurs.
Rthe power supplyisnot sufficient.
Driving systems187
Driving and parking
Z

Load compensation
The vehicle can compensatedifferences in
thevehicle level by raisingorlowering the
rear axle. This is the case, for example, if
people get out or if luggage is being loaded.
Load compensation takes place if:
Radoor or the trunk lid/tailgate is opened
Rthe parked vehicle is unlocked
For larger level changes, the engine must be
running.
4MATIC (permanent four-wheel drive)
If you fail to adapt your driving style, 4MATIC
can neither reduce the risk of accident nor
override the laws of physics. 4MATIC cannot
take account of road, weather and traffic
conditions. 4MATIC is only an aid. You are
responsible for the distance to the vehicle in
front,for vehicle speed, for braking in good
time and for staying in your lane.
Ifadrive wheel spins due to insufficientgrip:
ROnly depress the accelerator pedalasfar
as necessary when pulling away.
RAccelerate less when driving.
!Never tow the vehiclewith one axle
raised. This may damage the transfer case.
Damageofthis sort is not covered by the
Mercedes-Benz Limited Warranty. All
wheels must remaineitheronthe ground
or be fully raised. Observe the instructions
for towing the vehicle with all wheels in full
contact with the ground.
iIn wintry driving conditions, the maximum
effect of 4MATIC can only be achieved if
you use winter tires(M+S tires), with snow
chains if necessary.
4MATIC ensures that allfour wheels are
permanently driven. Together with ESP®,it
improves the traction of yourvehicle
wheneveradrive wheel spins due to
insufficient grip.
PARKTRONIC
Important safetynotes
PARKTRONIC is an electronic parkingaid with
ultrasonic sensors. It indicates visually and
audibly the distancebetween your vehicle
and an object.
PARKTRONIC is only an aid. It is not a
replacementfor your attention to your
immediate surroundings. You are always
responsible for safe maneuvering, parking
and exitingaparkingspace. When
maneuvering, parkingorpulling out of a
parkingspace, make sure that thereare no
persons, animals or objects in the area in
which you are maneuvering.
!When parking, pay particular attention to
objects above or below the sensors, such
as flower pots or trailer drawbars.
PARKTRONIC does not detectsuch objects
when they are in theimmediatevicinity of
thevehicle. You could damagethe vehicle
or the objects.
The sensors may not detect snow and other
objectsthat absorb ultrasonic waves.
Ultrasonic sources such as an automatic
car wash, the compressed-air brakes on a
truck orapneumatic drill could cause
PARKTRONIC to malfunction.
PARKTRONIC may not function correctly on
uneven terrain.
PARKTRONIC is activated automatically when
you:
Rswitch on the ignition
Rshift the transmission to positionD,RorN
Rrelease the parking brake
PARKTRONIC is deactivated at speeds above
11 mph (18 km/h). It is reactivated at lower
speeds.
PARKTRONIC monitors the area around your
vehicle using six sensors in the front bumper
and four sensors in the rear bumper.
Driving systems193
Driving and parking
Z

status indicator in the instrument cluster.
Whenaparking space has been detected, an
arrow towards the right or the left also
appears. By default, Active Parking Assist
only displays parking spaces on the front-
passenger side. Parking spaces on the
driver's side are displayed as soon as the turn
signal on the driver's side is activated. When
parking on the driver's side, this must remain
switched on until you acknowledge the use of
Active Parking Assist by pressing the
button on the multifunction steering wheel.
iTake note that Active Parking Assist
cannot measure the size of parking spaces
that are at right angles to the direction of
travel. You must decide for yourself
whether the vehicle will fit in the parking
space.
Aparking spaceisdisplayed while you are
driving past it, and until you are
approximately 50 ft (15 m) away from it.
Parking
GWARNING
ActiveParking Assist merely aids you by
intervening activelyinthesteering.Ifyou do
notbrakethere isariskofanaccident.
Always apply thebrakes yourself when
maneuveringand parking.
XStop thevehicle when theparking space
symbol shows thedesired parking spacein
theinstrumentcluster.
XShift thetransmission to positionR.
TheStart ParkAssist?Yes:OKNo:
message appearsinthemultifunction
display.
XTo cancel theprocedure:pressthe
buttononthemultifunction steering
wheel or pull away.
or
XTo park usingActiveParking Assist:
pressthebuttononthe multifunction
steering wheel.
ThePark Assist Active Accelerate
and Brake Observe Surroundings
message appears in the multifunction
display.
XLet go of the multifunction steering wheel.
XBack up the vehicle, being ready to brake
at all times. When backing up, drive at a
speed below approximately6mph
(10 km/h). Otherwise Active ParkingAssist
will be canceled.
iIn tight parkingspaces, you will achieve
the best parkingresults by backingupas
far as possible. When doing so, also
observe the PARKTRONICmessages.
XStop as soon as PARKTRONICsounds the
continuous warning tone, if not before.
Maneuveringmay be required in tight
parkingspaces.
ThePark Assist Active Select D
ObserveSurroundingsmessage appears in
the multifunction display.
XShift the transmission to positionDwhile
the vehicle is stationary.
Active ParkingAssist immediately steersin
the other direction.
ThePark Assist Active Accelerate
and Brake ObserveSurroundings
message appears in the multifunction
display.
iYou will achieve the best results by
waiting for the steering procedure to
completebefore pulling away.
XDriveforwards and be ready to brake at all
times.
XStop as soon as PARKTRONICsounds the
continuous warning tone, if not before.
198Driving systems
Driving and parking

Rif the camera is exposed to very bright light
Rif the area is lit by fluorescentlight or LED
lighting (thedisplay may flicker)
Rif there isasudden change in temperature,
e.g. when drivingintoaheatedgarage in
winter
Rif the camera lens is dirtyorobstructed
Rif the rear of your vehicle is damaged. In
this event, have the camera position and
settingchecked ataqualified specialist
workshop.
General notes
Example: Coupe
Rear view camerais located in the handle
strip of the trunk lid.
Rear view camerais an optical parking and
maneuveringaid. It shows the area behind
your vehicle with guide lines in the COMAND
display.
The area behindthe vehicle is displayed as a
mirror image, as in the rear view mirror.
iThe textofmessages shown in the
COMAND display depends on the language
setting. The following are examples of rear
view camera messages in the COMAND
display.
Activating/deactivating the rear view
camera
XTo activate:make sure that the SmartKey
is in position2in the ignition lock.
XMake sure that the "Activation byRgear"
setting is active in COMAND,see the
separate COMAND operatinginstructions.
XEngage reversegear.
The area behind the vehicle is shown in the
COMAND display with guide lines.
To deactivate:the rear view camera is
deactivated if you:
Rshift the transmission to positionP
Rdrive 33 ft (10 m) forwards
Rshift the transmission fromRto another
position after 15 seconds
Rdrive forwards ataspeed of over5mph
(10 km/h)
Displays in the COMAND display
The rear view camera may showadistorted
view of obstacles, show them incorrectly or
not at all. The rear view camera does not show
objects in the following positions:
Rvery close to the rear bumper
Runder the rear bumper
Rin the area immediately above the tailgate
handle
!Objects not at ground level may appear to
be further away than they actually are, e.g.:
Rthe bumper ofaparked vehicle
Rthe drawbar ofatrailer
Rthe ball coupling ofatrailer tow hitch
Rthe rear section of an HGV
Raslanted post
Use the guidelines only for orientation.
Approachobjects no further than the
bottom-most guideline.
200Driving systems
Driving and parking

Active Driving Assistance package
Generalnotes
The Active DrivingAssistance package
consistsofDISTRONICPLUS(Ypage 177),
Active Blind Spot Assist(Ypage 211) and
Active LaneKeepingAssist(Ypage 214).
Active Blind Spot Assist
Generalnotes
Active Blind Spot Assistusesaradar sensor
system, pointed toward the rear of the
vehicle, to monitor the area to the sides of the
vehicle which the driver is unable to see. A
warning displayinthe exterior mirrors draws
your attention to vehicles detected in the
monitored area. If you then switch on the
corresponding turn signal to change lane, you
will also receive an optical and audible
warning. Ifarisk of lateral collision is
detected, corrective braking may help you
avoidacollision. Beforeacourse-correcting
brake application, Active Blind Spot Assist
evaluates the space in the direction of travel
and at the sides of the vehicle. For this, Active
Blind Spot Assist uses radar sensors which
are pointed in the direction of travel.
Active Blind Spot Assist supports you from a
speed of approximately 20 mph (30 km/h).
For Active Blind Spot Assist to assist you
when driving, the radar sensor system must
be:
Ractivated(Ypage 232)
Roperational
Important safety notes
Active Blind Spot Assist is only an aid and is
notasubstitute for attentive driving.
GWARNING
Active Blind Spot Assist does not react to:
Rvehicles overtaken too closely on the side,
placing them in the blind spot area
Rvehicles which approach withalarge speed
differential and overtakeyour vehicle
Asaresult, Active Blind Spot Assist may
neither give warnings nor intervene in such
situations. There isarisk of an accident.
Always observe the traffic conditions
carefully, and maintainasafe lateral distance.
iUSA only:
This device has been approved by the FCC
asa"Vehicular RadarSystem". The radar
sensor is intended foruse in an automotive
radar system only. Removing, tampering
with, or altering the device will void any
warranties, and is not permitted by the
FCC. Do not tamper with, alter, or use in
any non-approved way.
Any unauthorized modification to this
device could void the user’s authority to
operate the equipment.
iCanada only: This device complies with
RSS-210ofIndustry Canada.Operation is
subject to the following two conditions:
1. This device may not cause harmful
interference, and
2. this device must accept any interference
received, including interference that may
cause undesired operation of the device.
Removal, tampering, or altering of the
device will void any warranties, and is not
permitted. Do not tamper with, alter, or use
in any non-approved way.
Any unauthorized modification to this
device could void the user's authority to
operate the equipment.
Radarsensors
The Active Blind Spot Assist radar sensors are
integrated into the front and rear bumpers
and behindacover in the radiator grill. Make
sure that the bumpers and the cover in the
radiator grill are free of dirt, ice or slush. The
rear sensors must not be covered, for
example by cycle racks or overhanging cargo.
Followingasevere impact or in the event of
damage to the bumpers, have the function of
the radar sensors checked ataqualified
Driving systems211
Driving and parking
Z

iWhen you reset the values in the "ECO
display",the values in the trip computer
"From start"are likewise reset. When you
reset the values in the trip computer "From
start", the values in the "ECO display" are
likewise reset.
Navigation system menu
Displaying navigation instructions
In theNavimenu, the multifunction display
shows navigation instructions. For more
information on navigation,see the separate
operatinginstructions.
XSwitchonCOMAND (see the separate
operatinginstructions).
XPress the\norbutton on the
steering wheel to select theNavimenu.
Routeguidance not active
Direction of travel
Current road
Routeguidance active
No change of direction announced
Distance to the destination
Distance to the nextchange of direction
$Current road
!"Follow the road's course" symbol
Change of direction announced without a
lane recommendation
Road intowhich the change of direction
leads
Distance to change of direction and visual
distancedisplay
$Change-of-direction symbol
Whenachange of direction is announced, you
will see symbol$for the change of direction
and distancegraphic.The distance
indicator shortenstowards the top of the
displayasyou approach the point of the
announced change of direction.
Change of direction announced with a
lane recommendation
Road into which the change of direction
leads
Distancetochange of direction and visual
distance display
$New lane duringachange of direction
!Uninterrupted lane
Lane recommendation
%Change-of-direction symbol
On multilane roads, the system can display
lane recommendation$for the next change
of direction. During the change of direction,
additional lanes may be displayed.
Lane recommendations are only displayed if
the relevant data is available on the digital
map.
224Menus and submenus
On-board computer and displays

Safety
Seat belts
ProblemPossible causes/consequences andSolutions

After startingthe
engine, the red seat
belt warning lamp lights
up for6seconds.
The seat belt warning lamp reminds the driver and frontpassenger
to fasten their seat belts.
XFastenyour seat belt (Ypage 56).

After starting the
engine, the red seat
belt warning lamp lights
up. In addition, a
warning tonesounds
for up to six seconds.
The driver's seat belt is not fastened.
XFasten your seat belt (Ypage 56).
The warning toneceases.

The red seat belt
warning lamp lights up
after the engine starts,
as soon as the driver's
or the front-passenger
door is closed.
The driver or front passenger has not fastened their seat belt.
XFasten your seat belt (Ypage 56).
The warning lamp goes out.
There are objectsonthe front-passenger seat.
XRemove the objectsfrom the front-passenger seat and stow
them inasecure place.
The warning lamp goes out.

The red seat belt
warning lamp flashes
and an intermittent
audible warning
sounds.
The driver or front passenger has not fastened their seat belt. You
are driving faster than 15 mph (25 km/h) or have briefly driven
faster than 15 mph (25 km/h).
XFasten your seat belt (Ypage 56).
The warning lamp goes out and the intermittentwarning tone
ceases.
Thereare objectsonthefront-passenger seat.You are driving
faster than 15 mph (25 km/h) or have briefly driven faster than
15 mph (25 km/h).
XRemove the objectsfrom the front-passenger seat and stow
them inasecure place.
The warning lamp goes out and the intermittentwarning tone
ceases.
Indicator and warning lamps in theinstrumentcluster265
On-boar dc omputer and displays
Z