2014 LEXUS RX270 Owners Manual

81
1
1-3. Adjustable components (seats, mirrors, steering wheel)
Before driving
RX350/270_EE
Driving position memory∗
Your preferred driving position (the position of the driver's seat, steering
wheel and outside rear view mirrors) can be memorized and recalled with
the touch of a button. It is also possible to set this function to activate auto-
matically when the doors are unlocked.
Three different driving positions can be entered into memory.
On some models, the same buttons are found on the front passenger’s side,
allowing the position of the front passenger’s seat to be memorized.
■Entering a position to memory
Turn the “ENGINE START STOP” switch to IGNITION ON
mode.
Adjust the driver’s seat, steering wheel and outside rear view
mirrors to the desired positions.
Press the “SET” button, then
within 3 seconds press button
“1”, “2” or “3” until the signal
beeps.
If the selected button has
already been preset, the previ-
ously recorded position will be
overwritten.
STEP1
STEP2
STEP3
∗: If equipped
RX350_270_EE_48D77E.book 81 ページ ２０１４年１月２４日　金曜日　午前１０時４分

82
1-3. Adjustable components (seats, mirrors, steering wheel)
RX350/270_EE
■Recalling the memorized position
Check that the shift lever is set in P.
Turn the “ENGINE START STOP” switch to IGNITION ON
mode.
Press button “1”, “2” or “3” until
the signal beeps to recall the
desired position.
STEP1
STEP2
STEP3
RX350_270_EE_48D77E.book 82 ページ ２０１４年１月２４日　金曜日　午前１０時４分

83
1-3. Adjustable components (seats, mirrors, steering wheel)
1
Before driving
RX350/270_EE
Linking driving position memory with door unlock operation (driver’s side only)
Record your driving position to button “1”, “2” or “3” before performing
the following.
Carry only the key (including the card key) to which you want to link the
driving position. If 2 or more keys are in the vehicle, the driving position
cannot be linked properly.
Shift the shift lever to P and close the driver's door. Turn the
“ENGINE START STOP” switch to IGNITION ON mode.
Press the desired button (“1”, “2” or
“3”) to recall the position. Then,
while keep pressing the button,
press the driver's door lock
switches (either lock or unlock)
until the signal beeps.
The driving position is recalled
when the driver's door is unlocked
using the entry function or wireless
remote control and the driver's
door is opened.
STEP1
STEP2
RX350_270_EE_48D77E.book 83 ページ ２０１４年１月２４日　金曜日　午前１０時４分

84
1-3. Adjustable components (seats, mirrors, steering wheel)
RX350/270_EE
Power easy access system (driver’s side only)
When the driver enters and exits the vehicle, the driver's seat and steer-
ing wheel will automatically perform the following operations:
Exiting the vehicle: When all of the
following actions have been per-
formed, the steering wheel will
move up and back to the point far-
thest away from the driver and the
seat will move backward (auto
away function):
• The shift lever has been shifted to P
• The “ENGINE START STOP”
switch has been turned off
• The driver’s seat belt has been
unfastened
Entering the vehicle: When either
of the following actions has been
performed, the steering wheel will
move toward the driver and seat
will move forward (auto return
function):
• The “ENGINE START STOP”
switch has been turned to ACCES-
SORY mode
• The driver’s seat belt has been fas-
tened
RX350_270_EE_48D77E.book 84 ページ ２０１４年１月２４日　金曜日　午前１０時４分

85
1-3. Adjustable components (seats, mirrors, steering wheel)
1
Before driving
RX350/270_EE
■When driving position memory is linked with door unlock operation
If the driver’s door is opened, the driver’s seat will move toward the memorized
position but stop slightly beforehand to allow easy access to the vehicle.
Turning the “ENGINE START STOP” switch to ACCESSORY mode or fastening
the driver’s seat belt moves the seat fully into the memorized position.
■Canceling the linked door unlock operation
Turn the “ENGINE START STOP” switch to IGNITION ON mode and
close the driver's door.
While pressing the “SET” button, press the driver’s door lock switches
(either lock or unlock) until the signal beeps.
■Operating the driving position memory after turning the “ENGINE START
STOP” switch off
Memorized positions (except for the steering wheel position) can be activated up
to 180 seconds after the driver’s door is opened and another 60 seconds after it is
closed again, even after turning the “ENGINE START STOP” switch off.
■Stopping seat position operation part-way through
Perform any of the following operations:
●Press the “SET” button.
●Press button “1”, “2” or “3”.
●Adjust the seat using the switches (only cancels seat position recall).
●Adjust the steering wheel using the tilt and telescopic steering control switch
(only cancels steering wheel position recall).
■Correct seat position
When the seat is in the most forward or most backward position, and the seat is
being moved in those directions, the system may not correctly recognize the cur-
rent position and the memorized position will not be correctly recalled.
■The auto away function for exiting the driver seat
If the seat is already close to the rearmost position, the auto away function may not
operate when the driver exits the vehicle.
■Customization
The distance that the driver’s seat moves backward during the auto away function
can be changed. (Customizable features →P. 6 2 2 )
STEP1
STEP2
RX350_270_EE_48D77E.book 85 ページ ２０１４年１月２４日　金曜日　午前１０時４分

86
1-3. Adjustable components (seats, mirrors, steering wheel)
RX350/270_EE
CAUTION
■Seat adjustment caution
Take care during seat adjustment so that the seat does not strike the rear passenger
or squeeze your body against the steering wheel.
RX350_270_EE_48D77E.book 86 ページ ２０１４年１月２４日　金曜日　午前１０時４分

87
1
1-3. Adjustable components (seats, mirrors, steering wheel)
Before driving
RX350/270_EE
Head restraints
■Removing the head restraints
■Adjusting the height of the head restraints (front seats)
■Adjusting the rear seat head restraints
Always raise the head restraints to the uppermost lock position during use.
Up
Pull the head restraints up.
Down
Push the head restraint down
while pressing the lock release
button.
Lock release button
Pull the head restraint up while pressing the
lock release button.
Lock release button
Make sure that the head restraints are
adjusted so that the center of the head
restraint is closest to the top of your ears.
RX350_270_EE_48D77E.book 87 ページ ２０１４年１月２４日　金曜日　午前１０時４分

88
1-3. Adjustable components (seats, mirrors, steering wheel)
RX350/270_EE
CAUTION
■Head restraint precautions
Observe the following precautions regarding the head restraints.
Failure to do so may result in death or serious injury.
●Use the head restraints designed for each respective seat.
●Adjust the head restraints to the correct position at all times.
●After adjusting the head restraints, push down on them and make sure they are
locked in position.
●Do not drive with the head restraints removed.
RX350_270_EE_48D77E.book 88 ページ ２０１４年１月２４日　金曜日　午前１０時４分