2014 Lexus CT200h display

2074-5. Using the driving support systems
4
Driving
CT200h_OM_OM76135E_(EE)
■Cruise control can be set when
●The shift position is in D.
●Vehicle speed is above approximately 40 km/h (25 mph).
■Accelerating after setting the vehicle speed
●The vehicle can be accelerated normally. After acceleration, the set speed resumes.
●Even without canceling the cruise control, the set speed can be increased by first accel-
erating the vehicle to the desired speed and then pushing the lever down to set the new
speed.
■Automatic cruise control cancelation
Cruise control will stop maintaining the vehicle speed in any of the following situations.
●Actual vehicle speed falls more than approximately 16 km/h (10 mph) below the preset
vehicle speed.
At this time, the memorized set speed is not retained.
●Actual vehicle speed is below approximately 40km/h (25 mph).
●VSC is activated.
■If the warning message for the cruise control is shown on the multi-information display
Press the “ON-OFF” button once to deactivate the system, and then press the button
again to reactivate the system.
If the cruise control speed cannot be set or if the cruise control cancels immediately after
being activated, there may be a malfunction in the cruise control system. Have the vehi-
cle inspected by any authorized Lexus dealer or repairer, or another duly qualified and
equipped professional.
WA R N I N G
■To avoid operating the cruise control by mistake
Switch the cruise control off using the “ON-OFF” button when not in use.
■Situations unsuitable for cruise control
Do not use cruise control in any of the following situations.
Doing so may result in loss of control and could cause an accident resulting in death or
serious injury.
●In heavy traffic
●On roads with sharp bends
●On winding roads
●On slippery roads, such as those covered with rain, ice or snow
●On steep hills
Vehicle speed may exceed the set sp eed when driving down a steep hill.
●During emergency towing
CT200h_OM_OM76135E_(EE).book Page 207 Friday, May 30, 2014 1 1:14 AM

2084-5. Using the driving support systems
CT200h_OM_OM76135E_(EE)
Dynamic radar cruise control∗
Dynamic radar cruise control supplements conventional cruise control with a
vehicle-to-vehicle distance control. In vehicle-to-vehicle distance control mode,
the vehicle automatically accelerates or decelerates in order to maintain a set
following distance from vehicles ahead. Indicators
Display
Set speed
Vehicle-to-vehicle distance button
Cruise control switch
∗: If equipped
Summary of functions
1
2
3
4
5
CT200h_OM_OM76135E_(EE).book Page 208 Friday, May 30, 2014 1 1:14 AM

2094-5. Using the driving support systems
4
Driving
CT200h_OM_OM76135E_(EE)
Press the “ON-OFF” button to acti-
vate the cruise control.
Radar cruise control indicator will come
on.
Press the button again to deactivate the
cruise control.
Accelerate or decelerate the vehicle
to the desired speed, and push the
lever down to set the speed.
“SET” will be displayed.
The vehicle speed at the moment the
lever is released becomes the set speed.
Setting the vehicle speed (vehicle-to-vehicle distance control mode)
1
2
CT200h_OM_OM76135E_(EE).book Page 209 Friday, May 30, 2014 1 1:14 AM

2134-5. Using the driving support systems
4
Driving
CT200h_OM_OM76135E_(EE)
When your vehicle is too close to a vehicle ahead, and sufficient automatic
deceleration via the cruise control is not possible, the display will flash and the
buzzer will sound to alert the driver. An example of this would be if another driver
cuts in front of you while you are following a vehicle. Apply the brakes to ensure
an appropriate vehicle-to-vehicle distance.
■Wa r n i n g s m a y n o t o c c u r w h e n
In the following instances, there is a possibility that the warnings will not occur:
●When the speed of the vehicle ahead matches or exceeds your vehicle
speed
●When the vehicle ahead is traveling at an extremely slow speed
●Immediately after the cruise control speed was set
●At the instant the accelerator is applied
Constant speed control mode differs from vehicle-to-vehicle distance control
mode. When constant speed control mode is selected, your vehicle will maintain
a set speed regardless of whether or not there are other vehicles in the lane
ahead. Press the “ON-OFF” button to acti-
vate the cruise control.
Press the button again to deactivate the
cruise control.
Switch to constant speed control
mode.
(Push the lever forward and hold for
approximately one second.)
Cruise control indicator will come on.
When in constant speed control mode, to return to vehicle-to-vehicle distance con-
trol mode, push the lever forward again and hold for approximately 1 second.
After the desired speed has been set, it is not possible to return to vehicle-to-vehicle
distance control mode.
If the power switch is turned off and then turned to ON mode again, the vehicle will
automatically return to vehicle-to-vehicle distance control mode.
Adjusting the speed setting: →P. 2 1 0
Canceling and resuming the speed setting: →P. 2 1 1
Approach warning
Selecting conventional constant speed control mode
1
2
CT200h_OM_OM76135E_(EE).book Page 213 Friday, May 30, 2014 1 1:14 AM

219
4
4-5. Using the driving support systems
Driving
CT200h_OM_OM76135E_(EE)
Lexus parking assist-sensor∗
Front corner sensors
Rear corner sensors
Rear center sensors
Turns the Lexus parking assist-sensor
on/off
When on, the indicator light comes on
to inform the driver that the system is
operational.
∗: If equipped
The distance from your vehicle to ne arby obstacles when parallel parking or
maneuvering into a garage is measured by the sensors and communicated via
the displays and a buzzer. Always check the surrounding area when using this
system.
Types of sensors
1
2
3
Lexus parking assist-sensor switch
CT200h_OM_OM76135E_(EE).book Page 219 Friday, May 30, 2014 1 1:14 AM

2204-5. Using the driving support systems
CT200h_OM_OM76135E_(EE)
When the sensors detect an obstacle, the following displays inform the driver of
the position and distance to the obstacle.
■Multi-information displayFront corner sensor operation
Rear corner sensor operation
Rear center sensor operation
■Lexus Display Audio or navigati on system screen (if equipped)
Lexus parking assist-sensor dis-
play
When the rear view monitor system*or Lexus parking assist monitor* is
not displayed.
A graphic is automatically displayed
when an obstacle is detected. The
screen can be set so that the graphic
is not displayed. ( →P. 2 2 3 )
: Select to mute the buzzer sounds.
Insert display
When the rear view monitor system*
or Lexus parking assist monitor* is
displayed.
A simplified image is displayed on
the right upper corner of the naviga-
tion system screen when an obstacle
is detected.
*: if equipped
Display
XVehicles with monochrome displayXVehicles with color display
1
2
3
1
2
CT200h_OM_OM76135E_(EE).book Page 220 Friday, May 30, 2014 1 1:14 AM

2214-5. Using the driving support systems
4
Driving
CT200h_OM_OM76135E_(EE)
■Distance display
Sensors that detect an obstacle will illuminate continuously or blink.
*1: The images may differ from that shown in the illustrations. (→P. 2 2 0 )
*2: Multi-information display
*3: Lexus Display Audio or navigation system screen
Sensor detection display, obstacle distance
Display*1Insert display
Approximate distance to obstacle
Front and rear corner
sensorRear center sensor
(continuous)(blinking slowly)
150 cm (4.9 ft.) to
60 cm (2.0 ft.)
(continuous)(blinking)
Front corner sensor:
50 cm (1.6 ft.) to 40
cm (1.3 ft.)
Rear corner sensor:
60 cm (2.0 ft.) to 45
cm (1.5 ft.)
60 cm (2.0 ft.) to
45 cm (1.5 ft.)
(continuous)(blinking rapidly)
Front corner sensor:
40 cm (1.3 ft.) to 30
cm (1.0 ft.)
Rear corner sensor:
45 cm (1.5 ft.) to 30
cm (1.0 ft.)
45 cm (1.5 ft.) to
35 cm (1.2 ft.)
(blinking*2 or
continuous
*3)
(continuous)
Less than
30 cm (1.0 ft.)Less than
35 cm (1.2 ft.)
CT200h_OM_OM76135E_(EE).book Page 221 Friday, May 30, 2014 1 1:14 AM

2234-5. Using the driving support systems
4
Driving
CT200h_OM_OM76135E_(EE)
You can change the buzzer sounds volume and the screen operating conditions.
XLexus Display Audio system
Press the “MENU” button on the Lexus Display Audio controller, and then
select “Setup” on the screen.
Select “Vehicle”, and then select “LEXUS park assist” on the screen.
Select the desired item.
XNavigation system
Press the “MENU” button on the Remote Touch, and then select “Setup” on
the screen.
Select “Vehicle”, and then select “LEXUS park assist settings” on the screen.
Select the desired item.The buzzer sounds volume can be adjusted.
On or off can be selected for Lexus parking assist-sensor display.
Rear center sensor display and tone indication can be set.
■The Lexus parking assist-sensor can be operated when
●Front corner sensors:
• The power switch is in ON mode.
• The shift position is in other than P.
• The vehicle speed is less than about 10 km/h (6 mph).(At any speed when the shift position is in R)
●Rear corner and rear center sensors:
• The power switch is in ON mode.
• The shift position is in R.
Setting up Lexus parking assist-senso r (vehicles with a Lexus Display
Audio or navigation system)
1
2
3
1
2
3
XLexus Display Audio screenXNavigation system screen
1
2
3
CT200h_OM_OM76135E_(EE).book Page 223 Friday, May 30, 2014 1 1:14 AM