2014 INFINITI QX60 Quick Reference Guide

7
3rd Row Power Folding Seats
The 3rd row seats can be folded flat for maximum
cargo hauling or extra storage space.
Before folding down the 3rd row seats:

•
The vehicle’s shift lever must be in the
P (PARK)
position or the N (NEUTRAL) position.
MANUAL SEAT FOLD DOWN
To fold the 3rd row seats flat:



1.

Pull the strap to release the head restraint
forward
01.



2.


Stow the 3rd row seat belts in the seat belt hooks
found in the cargo area
02.



3.


Pull up on the latch located on the corner of each

seatback and lower the seatback forward over the
seat base
03.
POWER UNFOLDING SEAT
When the ignition is in the OFF position, the power
unfolding seats are always operational.
If the ignition switch is in the ON position the power
unfolding seats are only operational when the shift
lever is in the P (PARK) or N(NEUTRAL) position.
To return the 3rd row seats to the upright position:



1.

Push and hold the switch. The seatback will rise

up while holding the switch.
A chime will sound once to indicate the start of the operation.
A warning chime will sound continuously if the seat is not in full uprig\
ht or folded position
when the ignition switch is placed in the
ON position.
For more information, refer to the “Safety — Seats, seat belts and supplemental restraint system (sectio\
n 1) ” of your
Owner’s Manual.
01
02
03
1591599_14b_Infiniti_QX60_QRG_100913.indd 710/9/13 11:09 AM

8
essential information
Tire Pressure Monitoring System (TPMS) with Tire Inflation Indicator
A Tire Pressure Low – Add Air warning message
will appear in the vehicle information display
01
and the low tire pressure warning light 02 will
illuminate when one or more tires are low on
pressure and air is needed.
•
The tire pressures should be checked when the


tires are cold. The tires are considered cold after
the vehicle has been parked for 3 hours or more
or driven less than 1 mi (1.6 km) at
moderate speeds.
When adding air to an under-inflated tire, the TPMS
with Tire Inflation Indicator provides visual and
audible signals to help you inflate the tires to the
recommended COLD tire pressure.
To use the tire inflation indicator:
1.


Move the shift lever to the
P (PARK) position and apply the parking brake.
2.


Place the ignition switch in the
ON position. Do not start the engine.
3.


Add air to the under-inflated tire and within a few seconds, the hazard \
warning lights will
start flashing.
4.


When the designated tire pressure is reached, the horn will beep once an\
d the hazard
warning flashers will stop flashing.
5.


Repeat this procedure for any additional under-inflated tires.
After tire pressures are adjusted, drive the vehicle at speeds above 16 \
MPH (25 km/h).
The Tire Pressure Low – Add Air warning message and low tire pressure warning light
will disappear.
When the low tire pressure warning light flashes for approximately 1 min\
ute and then
remains on, the TPMS is not functioning properly. Have the system checke\
d by an
INFINITI retailer.
Tire pressure rises and falls depending on the heat caused by the vehicl\
e’s operation and
the outside temperature. Low outside temperature can lower the temperatu\
re of the air
inside the tire, which can cause a lower tire inflation pressure. This m\
ay cause the low
tire pressure warning light to illuminate. If the warning light illumina\
tes, check the tire
pressure in your tires.
•
Check

the tire pressure (including the spare tire) often and always prior to long

distance trips.
The Tire and Loading Information label contains valuable information. Pl\
ea se refer to
section 9, “Technical and consumer information” in your Owner’s\
Manual for the location
of the Tire and Loading Information label.
For more information, refer to the “Instruments and controls (section 2)”, the “Starting and driving (section 5)” and the
“Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
01
02
1591599_14b_Infiniti_QX60_QRG_100913.indd 810/9/13 11:09 AM

Accessing the Front Cup Holders
To open the cup holders, push the lid 01 down
and release.
For more information, refer to the “Instruments and controls (section 2)”
of your Owner’s Manual.
Front Armrest/Center Console Storage Box
To access the top storage bin, pull up on the driver’s



side lever 01.
To access the bottom storage bin, pull up on the



passenger’s side lever 02.
For more information, refer to the “Instruments and controls (section 2)”
of your Owner’s Manual.
01
0102
Loose Fuel Cap
A LOOSE FUEL CAP
warning message will appear



in the vehicle information display 01 when the
fuel-filler cap is not tightened correctly.
To tighten, turn the cap clockwise until a single click



is heard.
The warning message will disappear when the vehicle



detects the fuel-filler cap is properly tightened and the




reset button 02 is pressed for about 1 second.
If the cap is not properly tightened, the Malfunction




Indicator Light may illuminate.
For more information, refer to the “Instruments and controls (section 2)”
and the “Pre-driving checks and adjustments (section 3)” of your
Owner’s Manual.
01
02
9
Fuel-filler Door
The fuel-filler door is located on the driver’s side of
the vehicle.
The fuel-filler door automatically locks/unlocks




when the driver’s door is locked/unlocked. To open the fuel-filler door, push the right side of



the fuel-filler door and release.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
1591599_14b_Infiniti_QX60_QRG_100913.indd 910/9/13 11:09 AM

essential information
Clock Set/Adjustment
DIGITAL CLOCK ADJUSTMENT
To adjust the time and the appearance
of the clock on the display:
1.


Press the

SETTING button on the control panel.
2.


Touch the

Others key.
3.


Touch the

Clock key.
The following settings can be adjusted:
• On-screen Clock:

The clock in the upper right corner
of the display can be turned ON or OFF.
• Clock Format (24h):

The clock can be set to 12 hours or 24 hours.
• Offset (hour):

The time can be adjusted by increasing or decreasing per hour.
• Offset (min):

The time can be adjusted by increasing or decreasing per minute.
• Daylight Savings Time:

The application of daylight savings time can be turned ON or OFF.
• Time Zone:

Adjust the time zone. Choose a time zone from the available list.
Press the BACK button to return to the previous screen.
For more information, refer to the “Monitor, climate, audio, phone and voice
recognition systems (section 4)” of your Owner’s Manual.
10
1591599_14b_Infiniti_QX60_QRG_100913.indd 1010/9/13 11:09 AM

11
first drive features
INFINITI Intelligent Key System
The INFINITI Intelligent Key system allows you to lock or unlock your
vehicle, open your liftgate and remotely start the engine. It is importa\
nt to
make sure the Intelligent Key is with you (that is, in your pocket or p\
urse).
REMOTE ENGINE START* (if so equipped)
The remote engine start system must be enabled in the vehicle
settings within the vehicle information display.
The remote engine start operating range is approximately 200 ft (60 m)\

from the vehicle. The effective operating range may be shorter due to
environmental conditions or obstacles between you and the vehicle.
For the remote engine start to function, the vehicle must be in
the P (PARK) position with the ignition off, and all the doors closed
and locked.
To start your vehicle remotely:



1.

Press the button
01
2. Within 5 seconds press and hold the remote engine start
button
02 for at least
2 seconds.
The engine will start and the parking lights will turn on.
Automatic climate control will begin heating or cooling the vehicle depe\
nding on the last
used mode.
The engine will run for 10 minutes and then turn off.
Repeat steps 1 and 2 to extend the time for an additional 10 minute peri\
od.

•
After
two remote starts the ignition switch must be cycled before the remote start can be
used again.
To start driving depress the brake pedal and push the ignition switch START/STOP button.
LOCKING AND UNLOCKING THE VEHICLE
The lock and unlock operating range of the
Intelligent Key is within 31.5 in (80 cm) from
each request switch.
To lock the vehicle, push either door handle



request switch 03 once or press the
button
01
on the key fob.
To unlock the vehicle, perform one of the following procedures:

•
Push
either door handle request switch
03 once; the corresponding door will unlock.
Push the door handle request switch again
within 30 seconds; all other doors
will unlock, or
• Press

the
button
04 on the key fob to unlock the driver’s side door. Press the



button

again;

all

other

doors

will

unlock.
*Laws in some communities may restrict the use of remote starters. Check\
local regulations before using this feature.
02
01
04
05
06
03
1591599_14b_Infiniti_QX60_QRG_100913.indd 1110/9/13 11:09 AM

LIFTGATE RELEASE
To open the rear liftgate, press the button
05 for longer than 1 second.
To close the rear liftgate, press the
button
05 again for longer than 1 second.
PANIC ALARM
The Intelligent Key can also be used to activate the panic alarm by pres\
sing and holding
the
button
06 for more than 1 second. Once activated, the panic alarm and headlights \
will stay on for a period of time.
INTELLIGENT KE
y
BATTER y DISCHARGE
If the battery of the Intelligent Key is discharged,
or environmental conditions interfere with the
Intelligent Key operation, start the engine according
to the following procedure:
1.


Move the shift lever to the
P (P ARK ) position.



2.

Firmly apply the foot brake.




3.

Touch the ignition switch with
the Intelligent
Key and a chime will sound.



4.

Within 10 seconds after the chime sounds, push the ignition switch while\
depressing
the

brake pedal and the engine will start.
For more information, refer to the “Pre-driving checks and adjustments (section 3)”, the “Starting and driving (section 5)” and
the “Maintenance and do-it yourself (section 8)” of your Owner’s Manual.
12
first drive features
Power Liftgate
When the liftgate is closed and locked, the
liftgate will open automatically by:

•
Pushing the power liftgate switch
01 on the instrument panel.
•
Pushing the liftgate opener switch 02, the
liftgate must be unlocked, or you must have the
Intelligent Key with you (in your pocket or purse).
•


Pressing the
button
03 on the INFINITI
Intelligent Key for more than 1 second.
The power liftgate operation can be
turned on or off by the power liftgate main
switch
04 on the instrument panel.


•
When the power liftgate main switch is pushed

to the OFF position, power operation is not
available using the power liftgate switch on the
liftgate
05 or the liftgate opener switch
02.
For more information, refer to the “Pre-driving checks and adjustments
(section 3)” of your Owner’s Manual.
0401
02
05
03
1591599_14b_Infiniti_QX60_QRG_100913.indd 1210/9/13 11:09 AM

13
Power Seat Adjustments
To slide the seat forward or backward, push the



control switch 01 forward or backward.
To recline the seatback, push the switch
02
forward or backward.

SEAT LIFTER
To raise o r lower the front portion or height of the



seat,

push the front or back end of the switch

01 up or down.
POWER LUMBAR SUPPORT (if so equipped for driver’s seat)

To adjust the seat lumbar support, push the front or back end of the swi\
tch 03.
For more information, refer to the “Safety — seats, seat belts and supplemental restraint system (se\
ction 1)” of your
Owner’s Manual.
2ND Row Seats
To slide the seat forward or backward, pull the



center of the bar 01 up and hold it while you slide
the seat forward or backward to the desired



position. Release the bar to lock the seat




in position.


To recline the seatback, pull up on the recline handle


02 and lean back. To bring the seatback forward, pull

the lever up and lean your body forward. Release the



lever to lock the seatback in position.

MULTI-MODE/CHILD SEAT ACCESS FUNCTION
This feature is not available on driver’s side of 2nd row seat.
If a child safety seat is installed on the passenger’s side of the 2nd row seat, the 3rd row



can be accessed without removing the child safety seat.


To access the 3rd row from outside the vehicle, lift up on the seatback release lever 03.
EZ ENTR
y
MODE
To enter the 3rd row from outside the vehicle, lift up on fully the seatback lever
03. This will release the back of the seat and fold up the seat cushion.
For access to the rear seat slide the entire seat forward
by pushing on the upper seatback area.
To return the seat to a locked position, push the upper seatback
rearward until the seatback and track are locked. Push the seat
cushion down. Locking the seatback will also lock the track.
For more information, refer to the “Safety — seats, seat belts and supplemental restraint system (se\
ction 1)”
of your Owner’s Manual.
010203
0102
03
1591599_14b_Infiniti_QX60_QRG_100913.indd 1310/9/13 11:09 AM

first drive features
3RD Row Manual Reclining Seatback
To recline the seatback, pull up on the latch 01
located on the outside corner of each seatback.




Lean back until the desired angle is obtained.


To bring the seatback forward again, pull up on the
latch
01 and move your body forward. The
seatback will move forward.
For more information, refer to the “Safety — seats, seat belts and
supplemental restraint system (section 1)” of your Owner’s Manual.
Automatic Drive Positioner (if so equipped)
Two positions for the driver’s seat, steering column



and outside mirrors can be stored in the automatic



drive positioner 01 memory.
Follo
w these procedures to set the
memory positions:


• Confirm the shift lever is in the P (PARK) position.
• Push
the ignition switch to the ON position.
• Adjust
the driver’s seat, steering column and



outside mirrors to the desired positions using the



adjusting switches for each feature.


•
Push
the SET switch and within 5 seconds, push the memory switch (1 or 2) for at least
1 second.
• The
indicator light on the memory switch you select will illuminate for approximately




5 seconds, and a chime will sound (if so equipped) when memory is stor\
ed correctly.


• The driver’s seat, steering column and outside mirror positions are now set to




your preference.
These memorized positions can also be linked to your INFINITI Intelligen\
t Key.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Outside Mirror Control Switch
To select the right or left side mirror, move the
control switch
01 right or left.
Adju
st each mirror to the desired position using
the switch
02.
To fold the outside rearview mirrors, push the
switch
03 to the
position. To unfold the
outside rearview mirrors, push the switch
03 to
the
position.
02
01
03
01
01
14
1591599_14b_Infiniti_QX60_QRG_100913.indd 1410/9/13 11:09 AM