2014 AUDI TT COUPE light

Downloaded from www.Manualslib.com manuals search engine 0
N
co
.-I
\D L/'l
N
L/'l
.-I Lights
and vision
Setting the correct compass calibration zone
Applies to vehicles: with digital compass
The correct compass calibration zone must first be set before the compass can give an accurate read­
ing.
Fig. 47 Map of compass calibration zones
..,. Press and hold button @
¢ page 44, Fig. 46
until the currently set zone number is displayed
on the interior mirror.
..,. Press
button @
repeatedly until the correct
zone number appears. The adjustment mode
will be ended automatically after a few sec­
onds.
Calibrating compass
Applies to vehicles: with digital compass
The compass must be re-calibrated if the display
is incorrect or inaccurate .
..,. Press and hold button @
until the letter Cap­
pears in the interior mirror .
..,. Drive in a circle at a speed of about 10 km/h un­
til a point of the compass is displayed in the in­
terior mirror. A
WARNING
Calibrate your compass at a location where
there is no traffic so that you do not endanger
yourself or other road users (accident risk).
45

Downloaded from www.Manualslib.com manuals search engine 0
N
co
....
\D Lfl
N
Lfl
.... -
Do not drive with the backrests of the front
seats reclined too far as otherwise the seat
belt and airbag could fail to restrain the
wearer properly in an accident, possibly
leading to injury.
Multi-function button
Applies to vehicles: with multi-function button
The multi-function button can be used to adjust
the side cushions .
.,. If
you turn the multi-function button@
¢ page 46, Fig. 49 to the left or right, the later­
al support on the seat will be increased/re­
duced by adjusting the side cushions on the
backrest.
@ Note
The air in the side cushions* is released when
you open the driver's door. This makes it eas­
ier to get in and out of the vehicle. The side
cushions are re-inflated as soon as you drive
the vehicle.
Easy entry function
The easy entry function facilitates access to the
rear seats.
Fig. SO Driver's seat: Lever on backrest
.,. To fold down the front seat backrest, pull the
ring and tip the backrest forwards.
A WARNING
Before you drive off, always make sure the
front seats are upright and securely locked in
position. Seats
and storage
Front centre armrest
Applies to vehicles: with centre armrest
The centre armrest can be adjusted to several
positions.
Fig. 51 Armrest between driver's seat and front passeng­
er's seat
.,. To adjust the angle, lift the armrest ¢ Fig. 51
until it engages in the desired position .
.,. To lower the armrest again, lift the armrest
slightly from the top click stop and then fold it
back down. Then raise the armrest to the de­
sired position if necessary.
You can move the armrest backwards or for­
wards.
There is a storage compartment underneath the
armrest.
Rear seat bench
Due to limited headroom, certain precautions
should be observed when the rear seats are in
use.
Fig. 52 Correct seating position in the rear seat
47

Downloaded from www.Manualslib.com manuals search engine Seats
and storage
.&_ WARNING
- The rear seat is only suitable for persons up
to 1.45 m.
- The distance between the occupant's head
and the rear window must be at least 2.5
cm when sitting upright in the rear seat -
otherwise serious head injuries could be
caused when closing the boot lid or in the
event of an accident. Always pay close at­
tention to passengers in the rear seat when
closing the boot lid.
- Heavy or hard objects must not be stored on
the luggage compartment cover -this puts
all passengers at risk of injury when opening
the boot lid or when severe braking occurs.
Ashtray
Fig. 53 Centre armrest raised: Ashtray
The ashtray is located in the centre console below
the centre armrest. Lift the lid to open the ash­
tray. Always put the ashtray safely back into the
holder after removing it (e.g. after emptying it).
.&_ WARNING
Never put waste paper in the ashtray, as this
could cause a fire.
48 Cigarette
Lighter and
electrical socket
Fig. 54 Centre armrest raised: Cigarette lighter
The cigarette lighter and electrical socket only
work when the ignition is on.
Using the cigarette lighter
.- Fold up the centre armrest (if necessary) to ac­
cess the cigarette lighter .
.- Press in the cigarette lighter .
.- When
the cigarette lighter springs out, pull it
out completely.
Using the electrical socket
.- Fold up the centre armrest (if necessary) to ac­
cess the electrical socket .
.- Ta
ke out the cigarette lighter (if necessary) .
.- Insert the plug of the electrical appliance into
the socket.
The cigarette lighter employs a standard 12 Volt
socket which can be used as a power source for
electrical appliances. The appliances connected
to the socket must not exceed a power rating of
lOOW.
.&_ WARNING
Ta ke care when using the cigarette lighter.
Carelessness or negligence when using the
cigarette lighter can cause burns.
CD CAUTION
- Always use the correct type of plugs to avoid
damaging the sockets.
- The cigarette lighter socket should only be
used for a short period of time as a power
source for electrical equipment. Please use
.,.

Downloaded from www.Manualslib.com manuals search engine the
electrical sockets* in the vehicle when
connecting equipment for longer periods.
@ Note
- Using electrical appliances with the engine
switched off will drain the battery.
- Do not attempt to charge the battery of
your vehicle using a small battery charger of
the type that is connected to the cigarette
lighter or the electrical socket inside the ve­
hicle.
Storage Cup holder
Fig. 55 Cup holder
Fig. 56 Centre armrest raised: Cup holder*
Cup holder* underneath the centre armrest
.. Fold
up the centre armrest ¢ page 47 .
.. If necessary, fold back the plastic retainer
¢Fig. 56.
_&. WARNING
- Do not put any hot drinks in the cup holders
0
� while
the vehicle is moving. You could be
� scalded if the hot liquid is spilt .
.-1
\D U'l
N
U'l
.-1 Seats
and storage
- Do not use hard china cups or glasses. These
could cause injury in the event of an acci­
dent.
CD CAUTION
You should avoid putting open drinks contain­
ers in the cup holders. The drinks could other­
wise spill over and cause damage to e.g. the
electrical equipment or the seat covers.
Glove box
The lockable glove box is equipped with a light.
Fig. 57 Glove box
.. To open the glove box, pull the catch on the lid
in the direction indicated (arrow)¢ Fig. 57 and
open the lid .
.. To close the glove box, push the lid upwards un­
til it engages.
_&. WARNING
To avoid the risk of injuries, always keep the
glove box lid closed when driving.
Storage compartments in the front seats
Applies to vehicles: with storage compartments in the front
seats
There is a fold-out drawer in the front part of
each front seat.
.. To
open the storage compartment, pull the
handle.
.. To close the storage compartment, close the lid
and push it in until it engages.
..,.
49

Downloaded from www.Manualslib.com manuals search engine Seats
and storage
@ Note
The storage compartment will hold a maxi­
mum weight of 1 kg.
Coat hooks
Applies to vehicles: with coat hooks
.&_ WARNING
- Make sure that any items of clothing hang­
ing from the coat hooks do not obstruct
your view to the rear.
- Only use the coat hooks for light items of
clothing and make sure that there are no
heavy or sharp objects in the pockets.
Luggage compartment
General notes
.&_ WARNING
Please refer to the important safety notes on
¢ page 201, Stowing luggage safely.
Luggage compartment cover
The luggage compartment cover blocks the view
into the luggage compartment.
Fig. 58 Open boot Lid with closed luggage compartment
cover
so Fig.
59 Luggage compartment cover released
Removing the luggage compartment cover
� To release the luggage compartment cover,
turn the catch to the horizontal position
¢Fig. 58.
� Take hold of the luggage compartment cover by
the sides and pull it in the direction of the ar­
rows ¢Fig. 59.
Installing the luggage compartment cover
� Fit the retainers onto the pins and slide the lug­
gage comp artment cover upwards.
� Turn the catch to the vertical position (apply
light pressure only).
.&_ WARNING
- The luggage compartment cover must al­
ways be fixed properly -risk of accident!
- Th e luggage compartment cover should not
be used as a storage shelf. Items placed on
this cover could cause injury in an accident
or if the brakes are applied suddenly.
CD CAUTION
Hard objects placed on the luggage compart­
ment cover could chafe against the wires of
the heating element or aerial in the rear win­
dow and cause damage.

Downloaded from www.Manualslib.com manuals search engine 0
N
co
....
\D Lfl
N
Lfl
.... Heating
and cooling
Air conditioner
Description
The air conditioner heats, cools and dehumidifies
the air inside the vehicle. It operates most effec­
tively with the windows closed. If the vehicle has
been standing in the sun, it may cool down faster
if you open the windows briefly to let the hot air
escape.
The pollution filter removes impurities, such as
dust and pollen, from the air.
@ For the sake of the environment
If you wish to save fuel, switch off the cooling
mode on the air conditioner by pressing the
Controls for manual air conditioner
Applies to vehicles: with manual air conditioner
Fig. 64 Manual air conditioner: Controls
The rotary controls and switches are used to con­
trol the functions. The LED in the corresponding
button lights up when the function is switched
on.
For a comfortable climate inside the vehicle:
- In the summer, adjust the temperature to just
a few degrees below the outside temperature
- Do not turn the blower up too high
- Do not point the air outlets directly at the occu-
pants Heating
and cooling
!AJC! button in the rotary control @. This will
also reduce emissions.
ijJ} Note
- Keep the air intake slots in front of the
windscreen clear of snow, ice and leaves to
ensure unimpaired heating and cooling, and
to prevent the windows misting over.
- Condensation can drip off the air cooling
system and form a pool underneath the ve­
hicle. This is normal and does not indicate a
leak.
- If you notice, for instance, that the seat* or
rear window heating is not working, it may
have been temporarily switched off by the
power management function. These sys­
tems will be available again as soon as suffi­
cient electrical power is available.
Key-coded settings
Certain settings will be automatically stored and
assigned to the remote control key in use.
- Manual air conditioner: Seat heating (driver's
side), !AIC!
button.
� Adjusting the blower speed
The rotary control (!) can be used to adjust the
blower speed in small steps. You should Leave the
blower on at a Low setting to prevent the
...,
53

Downloaded from www.Manualslib.com manuals search engine Controls
for automatic air conditioner
Applies to vehicles: with automatic air conditioner
Fig. 65 Automatic air conditioner: Controls
The rotary controls, the buttons in the rotary con­
trols and the switches are used to control the
functions. The functions can be switched on and
off by pressing the buttons. The LED in the corre­
sponding button lights up when the function is
switched on.
We recommend pressing the !AUTO! button and
setting the temperature to 22 °C (72 °F). The air
conditioner is fully automatic, and will maintain
the desired temperature at a constant level. The
temperature of the air supplied to the interior,
the blower speed and the air distribution are
regulated automatically. When the heater is on,
the blower normally only switches to a higher
speed once the coolant has warmed up suff icient­
ly (this does not apply to the defrost setting).
Key-coded settings: The automatic air condition­
er settings are automatically stored and assigned
to the remote control key which is being used.
� Adjusting the blower speed
The rotary control (D can be used to adjust the
blower speed in small steps. You should leave the
blower on at a low setting to prevent the win­
dows from misting up. You can adjust the blower
speed manually. Press the !AUTO! button for au-
� tomatic
control of the blower speed.
co ....
\D L/'l
N
L/'l
.... Heating
and cooling
IAIC! Switching air cooling on/off
The air cooling mode is switched on/off when the
!A IC
! button
is pressed. When the air cooling is
switched off, the air is neither cooled nor dehu­
midified. The windows may mist up as a result.
The air cooling is switched off automatically at
low outside temperatures (below zero).
The rotary control @ can be used to adjust the
temperature.
I • I •I Selecting
the temperature
The rotary control @ can be used to adjust the
temperature in small steps.
IAUTO! Switching automatic mode on/off
The automatic mode is switched on when the
!AUTO I
button is pressed. The AUTO mode is
switched off immediately when you operate any
of the manual air controls. The automatic mode
maintains a constant temperature inside the ve­
hicle. Air temperature, output and distribution
are regulated automatically.
Adjusting the air distribution
The rotary control @ can be used to adjust the
air distribution. Press the !AUTO! button for au­
tomatic air distribution.
The round air outlets in the dashboard can be ad-
justed ¢ page 56.
..,.
55

Downloaded from www.Manualslib.com manuals search engine Driving
Driving
General notes
Running in
A new vehicle should be run in over a distance of
1,500 km. For the first 1,000 km the engine
speed should not exceed 2/3 of the maximum
per missible engine speed -do not use full throt­
tle. From 1,000 to 1,500 km you can gradually
increase the engine rpm and road speed.
During its first few hours of running, the internal
friction in the engine is greater than later on
when all the moving parts have bedded down.
How the vehicle is driven for the first 1,500 km
also influences the engine quality. After this peri­
od you should continue driving at moderate en­
gine speeds, in particular when the engine is
cold. This helps to reduce wear and tear on the
engine and increases the potential mileage which
can be covered by the engine.
You should also avoid driving with the engine
speed too Low. Change down to a lower gear
when the engine no longer runs "smoothly". Ex­
cessively high engine speeds are prevented by an
automatic rev limiter.
Driving through water on roads
Please note the following in order to prevent
damage to the vehicle when driving through wa­
ter (e.g. on flooded roads):
- The water level must not be higher than the ve­
hicle's underbody.
- Do not drive faster than walking pace.
A WARNING
After driving through water, mud, sludge,
etc., the braking effect can be delayed slightly
due to moisture on the discs and brake pads.
Applying the brakes carefully several times
will remove the moisture and restore the full
braking effect.
58 CD
CAUTION
Parts of the vehicle (e.g. engine, gearbox, run­
ning gear or electrical components) can be
badly damaged when driving through water.
ij} Note
- It is advisable to check the depth at the
deepest point before approaching the wa-
ter.
- Do NOT stop the vehicle, drive in reverse or
switch off the engine before you are out of
the water.
- Bear in mind that waves created by oncom­
ing traffic could exceed the permissible
wading depth of your vehicle.
- Avoid driving through salt water (corrosion).
How to improve economy and minimise
pollution
Fuel econom y, environmental impact and wear
on the engine, brakes and tyres depend largely
on the way you drive the vehicle. By adopting an
economical driving style and anticipating the
traffic situation ahead, you can reduce fuel con­
sumption by 10-15%. The following section gives
you some tips on lessening the impact on the en­
vironment and reducing your operating costs at
the same time.
Anticipate well in advance
A car uses most fuel when accelerating. If you an­
ticipate hazards and speed changes well in ad­
vance, you will need to brake less and thus accel­
erate less. Wherever possible, let the car slow
down gradually with a gear engaged, for in­
stance when you can see that the next traffic
lights are red.
Change gear early to save fuel
An effective way of saving fuel is to change up
quickly through the gears. Running the engine at
high rpm in the lower gears uses an unnecessary
amount offuel. Press the accelerator slowly and
avoid using the "kick-down" feature.
...,