2014 AUDI R8 SPYDER engine

188 Checking and filling
cracked and weakened when the battery
froze.
- Charge the battery in a we ll ventilated
area. Keep away from open f lame or elec­
trical spark. Do not smoke. Hydrogen gas
generated by the battery is explosive.
- To reduce the danger of explosion, never
connect or disconnect charger cables
wh ile the charger is operating.
- Fast charg ing a battery is dangerous and
should only be attempted by a compe­
tent technicia n w ith the proper equip­
me nt.
- Battery acid that may spill during charg­
ing should be washed off with a solution
of warm water and baking soda to neu­
tralize the acid.
(D Note
Never use a fast charger as a booster to
start the engine. This will seriously dam­
age sensitive electronic components, such
as control units, relays, rad io, etc., as we ll
as t he battery charger.
(D Tips
- The vehicle battery must not be charged
with a standard small charger that p lugs
i nto the c igarette lighte r o r outlet.
- Only charge the battery through the con­
nect ions in the luggage compartment.
Windshield washer
container
Fig. 148 Luggage compartment: Wind shie ld washer
fl uid reser voir
T he washer fluid container is marked with the
symbol
O on its cap ~page 174, fig. 136 .
,. Lift the fi ller cap tongue to add washer flu­
id. You can fil l the container to the top.
,. Press the cap back onto the filler neck after
fi lling the container .
You can find the reservo ir
c a p acit y in the table
in
~ page225
Clean water should be used when filling up. If
possible, use soft water to prevent scaling on
the washer jets. Always add a glass cleane r
solution (with frost protection in the winter).
(D Note
- Do not mix e ngine coolant ant ifreeze or
any other additives to fill up the w ind­
shield washer reservoir .
- Do not use g lass cleaners conta ining
pai nt so lvent; you risk damaging the
paint.

194 Tire s and wheel s
that are stored . The system does not recog ­
nize the load cond ition of your vehicle.
See the il lustration ~
fig. 149 for the location
of the label on dr iver's side 8-pillar (color of
the actua l labe l and exact location on the ve­
hicle wi LL vary slightly).
Note that the followi ng tab le is accurate at
the time o f go ing to press and is subject to
change. In the event of discrepancies, the tire pressure label on driver's s
ide 8 -pillar always
takes precedence .
T he table below l ists t he recommended cold
t ire inflat ion pressu res for the Aud i mode l
covered by your Owner's Literat ure at the vehi ­
cle's capacity weight and the tir e sizes i nstal­
l ed on the respective models as orig inal
equipment, or as a facto ry option.
I Model / \I Tire designation
Tire pressure front Tire pressure rear I
Engine
normal load full load normal load full load
condition condition condition condition
PSI II kPA PSI II kPA PSI ]I kPA
PSI II kPA
RS: 235/35 R19 91 Y XL 45
310 45 310
4 .2 liter
295 /30 R19 lOOY X L 280
8-c ylin-
305/30 R1 9 102V
XL
der 41
280 41
280
RS: 235/35 R19 91 Y XL 45
5.2 liter 295 /30 R19 l00Y XL 41 280 41
280
10-cyl-
305 /30 R19 102V XL
inder 41 280 41 280
--XL= reinforc ed or extra load tire. It may also a ppear as xl , EXTRA LOAD, or RF on the tire side·
wall.
Because tec hnical changes may be made to
ve hicle equ ipment dur ing the model yea r, a l­
ways compare the tire size designation on the
tire pressure labe l on your vehicle w ith the
tires on your vehicle . Make s ure that the t ire
size information on the ve hicle label is the
same as the size of the tires on the vehicle.
This is especially important if the vehicle be­
longs to someone else or you bough t the veh i­
cle with different rims/tires or you bought the
ve hicle as a previously owned vehicle .
Remember, your safety and that of your pas­
sengers also depends on mak ing sure that
load limits are not exceeded . Vehicle load in ­
cludes everybody and everything in and on the
vehicle. These load lim its are technically refer­
r ed to as the vehicle 's Gross Vehicle We ight
Rating ("GVWR"). The G ross Ax le Weight Rat­
ing ("GAWR") is the maximum load that can
be applied at each of the vehicle's two axles .
The Gross Vehicle Weight Rating and the
G ross Axle Weight Rating are listed on the safety compl
iance sticker label located on the
driver's side 8-pillar. The tire p ressure labe l on
yo ur Audi lists the max im um combined
weight of all o f the occ upants and luggage or
othe r ca rgo that the vehicle can carry. Fo r the
location of the tire pressure label
~ fig . 149.
A WARNING
Overloading a vehicle can cause loss of ve­
h icle contro l, a crash or other accident, se­
rious personal injury, and even death.
- Carrying more we ight than your veh icle
was designed to carry will prevent the
veh icle from handling properly a nd i n­
crease the risk of a loss of vehicle con ­
trol.
- The brakes on a vehicle that has been
overloaded may not be able to stop the
veh icle w ith in a safe distance.
- Tires on a vehicle that has been overload ­
ed can fail suddenly ca using loss of con­
trol and a crash.

210 What do I do now?
What do I do now?
Trunk escape handle
Appl ies to vehicles: wit h tru nk escape hand le
In case of an emergency, the front lid can be
opened from the inside using the trunk es­
cape handle .
.,. To
open the front lid pu ll the handle.
The trunk escape handle inside the luggage
compartment is made of fluorescent material
to g low in the dark.
A WARNING
The trunk escape handle is to be used only
in an emergency.
Vehicle tool kit
The tools are stored underneath the floor
panel in the luggage comportment.
Fig. 153 Luggage compartment: ve hicle tool k it
.,. Swing the luggage compartment floor up-
wards .
.,. Remove the vehicle tool kit.
The onboard tool kit includes:
- Hook for removing hub cap
- Lug wrench
- Alignment pin for changing wheels
- Screwdriver with reversible blade
- T owing eye
- Jack* (not a vehicle component; contact your
authorized Aud i dealer if needed)
Some of the on board items listed above are provided on certain models only or are option­
a l extras. Before
returning the jack* to its place, retract
t h e jack arm fully.
A WARNING
-
Improper use of the vehicle jack can cause
serious personal injuries.
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts can­
not attain the necessary tightening tor­
que if you use the hex head, potentially
causing an accident.
- The factory-supplied jack is intended on­
ly for your vehicle model. Under no cir­
cumstances should it be used to
lift
heavy veh icles or other loads; you risk in­
juring yourself.
- Never start the engine when the vehicle
is raised, which could cause an acc ident.
- Support the vehicle securely with appro­
priate stands if work is to be performed
underneath the vehicle; otherwise, there
is a potential risk for injury.
- Never use the jack supplied with your
Aud i on another vehicle, part icularly on a
heav ier one. The jack is only suitable for
use on the vehicle it came with.
Tire repair
General and safety pointers
Applies to veh icles: w it h Tire Mob ility System
Tire repair is intended only for temporary,
short-term use.
Fig . 154 Tire damage for wh ich the Tir e Mob ility Sys ­
te m is no t suited
Your vehicle is equipped with a tire repair kit,
the
Tire Mobility System (TMS). .,,.

-Che ck the tire p re ss ure on the spare imme­
diatel y afte r mounting.
- Hav e the wheel b olt tightening torque
checked with a torque wrench a s soon a s
possib le by you r auth orized Audi dealer or
a qu alified ser vice sta tio n.
- With steel and allo y w heel rim s, the wheel
bolts are correctl y tight ened at a to rq ue of
90 ft lb (1 20 Nm ).
- If yo u notice while changin g a ti re th at the
wheel bolts are co rrod ed and diff icult to
turn , then they should be repl aced before
y ou check the t ighten ing to rqu e.
- Replace the flat t ire with a new one and
ha ve it installed on your vehicle as soon as
possib le . R emount th e wh eel co ver .
Until then, driv e with extra care and at re ­
d uced speeds.
A WARNING
- If you are going to equip your vehicle
with t ires or rims wh ich differ from those
w hich were factory installed, then be
sure to read the informat ion
~page 199,
New tires and replacing tires and
wheels.
- Always store the tools securely in lug­
gage compa rtment. Otherw ise, in an ac­
c ident o r sudden mane uver they could fly
f orward, causing inju ry to passengers in
the vehicle .
(D Note
Do not use commerc ia lly available t ire
sealants. Othe rwise, the elec trical compo­
nents of the tire pressure monitoring sys­
tem* will no longer work properly and the
sensor for the tire pressure monitoring
system wi ll have to be replaced by a qua li­
fied workshop.
What do I do now? 217
Jump-starting
General
If necessary, the engine can be started by
connecting it to the battery of another vehi ­
cle.
If the engine should fail to start because of a
discharged or weak battery, the battery can be
connected to the battery of
another vehicle,
us ing a
pair of jump er cabl es to start the en­
gine.
Both batteries must be rated at 12 volts . The
capacity (Ah) of the booster battery must not
be substantia lly less than the capac ity of the
discharged battery .
Jumper cables
Use only jumper cables of suff ic ient ly large
cro ss se ction to safely car ry the starter cur ­
rent . Refer to the manufacturer's specifica­
tions .
Use only jumper cab les which have
insulated
term inal clamps and are properly marked for
dist inction:
plu s(+) cable : in most cases colored r ed
m inu s(-) cable :
in most cases colored black
A WARNING ~
Batteries contain e lectric ity, acid, and gas .
Any of these can cause very serious or fata l
injury. Follow the instructions below for
safe handling of your vehicle's battery.
-Always shield your eyes and avo id lean-
ing over the battery whenever poss ible.
- A discharged battery can a lready freeze
at temperatures just below 32 °F (0 °(). Before connect ing a jumper cable , the
frozen battery must be thawed com ­
pletely, othe rwise it could explode .
- Do not allow battery acid to contact eyes
or skin . Flush any contacted area with
wate r immediately .
- Improper use of a booster battery to
start a vehicle may cause an explosion. •
•

218 Wh at do I do now ?
-Vehicle batteries generate explos ive gas­
es. Keep sparks, flame and lighted ciga­
rettes away from batteries.
- Do not try to jump start any vehicle with
a low acid level in the battery.
- The voltage of the booster battery must
also have a 12-Volt rating. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged bat­
tery. Use of batteries of different voltage or substant ially different "Ah" rating
may cause an explos ion and personal in­
Jury.
- Never charge a frozen battery. Gas trap­
ped in the ice may cause an explosion.
- Never charge or use a battery that has
been frozen. The battery case may have
be weakened.
- Use of batteries of different voltage or
substant ially different capacity (Ah) rat­
ing may cause an explosion and injury.
T he capacity (Ah) of the booster battery
should not be lower than that of the dis­
charged battery.
- Before yo u check anything in the engine
compartment, always read and heed all
WARNINGS ¢
page 172, Working in the
engine compartment.
(D Note
- Applying a higher vo ltage booster bat­
tery wi ll ca use expensive damage to sen­
sitive electronic components, s uch as
control units, relays, radio, etc.
- There m ust be no e lectrica l contact be­
tween the vehicles as otherwise current
could already start to flow as soon as the
positive(+) terminals are connected .
(0 Tips
-The discharged battery must be proper ly
connected to the vehicle's electrical sys­
tem.
- Switch off any car phone, or follow the
car phone instructions for this situation.
Use of jumper cables
Make sure to connect the jumper cable
clamps in exactly the order described below!
F ig . 1 63 Luggage compartment: co nnectors for a
charge r and jump start cables
Fi g. 1 64 Jump start us ing the battery in a nother vehi ­
cle: A· Fema le socket, B • D isc harge
The battery is located in the luggage compart­
ment¢
page 185. T he front lid can be opened
i n an emergency¢
page 34.
Do not connect the negative cable d irectly to
the negative term inal on the battery. Connect
it to a
jump st a rt pin instead ¢ fig. 163.
Connect the po sitive cable (red ) to the
positive terminal
1. Co nnect one end of the red jumper cable
¢
fig . 164 (!) to the positive terminal of
discharged battery @.
2 . Connect the other end of the red jumper
cable to the positive terminal @of the
booster battery @.
Connect the n egativ e cable (black ) to the
n egati ve terminal
3. Connect one end of the b lack jumper ca­
ble @ to the negative terminal of the
booster battery @. .,.

4. Secure the other end to the jump start pin
© for the discharged battery@.
Starting the engine
.,. Start the eng ine of the vehicle providing as­
s istance and allow it to run at id le.
.,. Now start the engine of the vehicle with the
discharged battery .
.,. If the engine does not start: Stop trying af­
ter 10 seconds and then try again after
about 30 seconds .
.,. Disconnect the cable while the engine is
running in exactly
reverse order to that de­
scribed.
The battery is vented to the outside to prevent
gases from entering the vehicle interior. Make
sure that the jumper clamps are well connect­
ed with their
metal ports in full contact with
the battery termina ls.
A WARNING
To avoid serious personal i njury and dam­
age to the vehicle, heed all warnings and
instructions of the jumper cable manufac­
turer.
If in doubt, ca ll for road service .
- Jumper cables must be long enough so
that the vehicles do not touch.
- When connecting jumper cables, make
sure that they cannot get caught in any
moving parts in the engine compart­
ment.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
c:> page 172, Working in the
engine comportment.
Improper hook-up of jumper cables can ru­
in the generator.
- Always connect POSITIVE( +) to POSI­
TIVE(+), and NEGATIVE(-) to NEGATIVE
( - ) ground post of the battery manager
control unit.
- Check that all screw plugs on the battery
ce lls are screwed in firmly. If not, tighten
plugs prior to connecting clamp on nega­
tive battery terminal.
-
What do I do now? 219
- Please note that the procedure for con ­
necting a jumper cable as described
above applies specifically to the case of
your vehicle being jump started. When
you are giving a jump start to another ve­
hicle, do
not connect the negative(-) ca­
ble to the negative(-) terminal on the
discharged battery@. Instead, securely
connect the negative(-) cable to eithe r a
solid metal component that is firmly
bolted to the engine block or to the en­
gine block itself. If the battery that is be­
ing charged does not vent to the outside,
escaping battery gas could ignite and ex­
plode!
Emergency towing
with commercial tow
truck
' General hints
Your Audi requires special handling for tow­
ing.
The following information is to be used by commercial tow truck operators who know
how to operate their equipment safely.
- Never tow your Audi, towing will cause dam­
age to the engine and transmission.
- Never wrap the safety chains or winch cables around the brake lines.
- To prevent unnecessary damage, your Audi
must be transported w ith a car carrier (flat
bed truck) .
- To load the vehicle on to the flat bed, use
the towing loop found in the vehicle tools
and attach to the front anchorage
c:> page 220 .
A WARNING
A vehicle being towed is not safe for pas­
sengers . Never allow anyone to ride in a
vehicle be ing towed, for any reason.
•
•

General information Explanation of
technical data
Som e of t he technical data listed in this man ­
ual require further explanation.
The technical data for your vehicle are listed in
the charts starting on
Q page 225. This chap­
t e r p rovides general informa tion, notes and
r estr ictions wh ich app ly to these data .
Vehicle identification
The key data are given on the vehicle identifi­
cat io n number
(V IN) pla te and the vehicle da­
ta sticker.
Fig. 1 68 Vehicle I dent ificat ion Num ber {VlN) p la te: lo ­
cation o n driver's side dash pa nel
Fi g. 1 69 The ve hicle identificat ion label -in the foot­
well on the passenger's side
The Vehicle Identification Number (VlN)
is located on the d river's side so tha t it is v is i­
b le from the outsi de throug h the windshield -
see
c!) fig. 168. You can also disp lay the Vehi ­
cle Ident ificat ion Number of your vehicle in
the Driver Information display
Q page 22.
General inform ation 223
The vehicle identification label
is lo cated wi th the fuses in t he footwe ll on the
passenger 's side
Q page 221 .
The label c!) fig. 169 shows th e fo llow ing vehi­
cl e data :
(D Product ion cont ro l No .
@ Vehicle identific ation No.
@ Type code number
© Type designat ion/engine o utput in K ilo-
wat ts
® Engine and transm ission code letter
® Pa int No./lnterior
0 Option al eq uipment No.'s
Vehicle data 2 to 7 are a lso fo und in your War­
ranty
& Mai nte nance bookle t.
The safety compliance sticker is your assurance that your new vehicle com­
plies with a ll applicable Federal Motor Vehicle
Safety Standa rds which were in effect at the
time the ve hicle was manufactur ed . You can
find this sticke r o n the left doo r jamb.
It
sh ows the month an d ye ar of pro duction and
t he ve hicl e ident ifi cat io n number of yo ur vehi ­
cle (perfora tion) as well as the G ross Vehicle
Weight Rating (GVW R) and the Gross Axle
Weight Rating (GAWR) .
The high voltage warning label i s lo cated on the lock ca rrie r.
The spark ignition system complies with
the Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
T he Gro ss Vehicle Weigh t Rat ing (GVWR), and
the Gross Axle We igh t Rati ng (GAWR) for
fron t and rear are lis ted on a sticker on the
l eft door jamb .
T he Gro ss Vehicle Weigh t Rat ing incl udes the
weight o f the bas ic ve hicle plus f ull fuel t ank,
oi l and coo lant, plus maximum load, which in­
cludes passenger we ight (150 lbs./68 kg per ..,.

Data
Data
430 hp, 4.2 liter 8-cyl. engine
Applies to vehicles: with 4.2 liter 8-cyl. engine
Engine data
Maximum output SAE net
Maximum torque SAE net
No. of cylinders
Displacement
Stroke
Bore
Compression ratio
Firing sequence
Fuel
Dimensions (approx.)
Length (with license plate bracket)
W idth (across mirro rs)
He ight (unloaded) 430@ 7900
hp@rpm
lb-ft@ rp m
-~--
CID (cm3
)
in (mm)
in (mm)
---·
317 @4500 - 60 00
8
254 (4 163)
3 .65 (92 .8)
3.33 (84 .5)
12.5: 1
1-5-4-8-6-3-7-2
Premium unleaded (91 AKI) Recommended f or max i­
mum eng ine perf orman ce. Fu rther detai ls~
p age 16 7,
G asoline
in (mm)
in (mm)
in (mm)
T urning circle diameter (curb to curb) ft . (m) 174.6 (4435)
80.0 (2029)
49 (1252)
38. 7 ( 11.80)
Capacities (approx.)
Fuel tank
- Total capacity
- Reserve (of total capacity)
Windshield washer fluid container
Engine oil
with filte r change gal/liters
21.1 / 80
ga I/liters 2.6 / 10
quarts/liters 4.2 / 4.0
qua rts/liters 10.6 / 10
225
•
•