2014 AUDI Q5 spare wheel

_& WARNING
-The chock cannot fulfil its funct ion and
may lose its stability if the "tabs" on the
support plate are not inserted cor rectly
into the elongated holes in the base
pla te. If th is happens, the vehicle may
st ar t to move whi le a wheel is being
changed .
- Never use the folding chocks if they are
damaged or i f th ey have not been assem ­
bled correct ly .
Removing bass box
Applies to vehicles: with bass box
Before the inflatable spare tire* can be taken
out, the bass box must
be removed.
Fig . 2 13 Spare w hee l well : Bas s box
Removing bas s bo x
.,. Lift up the cargo floor using the hand le .
.,. Sq ueeze the locking tabs
c:!;> fig . 213 (D of
the connector.
.,. Disconnect the connector @and place the
lead to one side.
.,. Turn the large screw counter -clockwise .
.,. Carefu lly remove the bass box .
Install ing bas s bo x
.,. Carefu lly place the bass box in the wheel.
The inscr ipt ion "FRONT" on the bass box
must face forward .
.,. Reconnect the connector that was removed .
.,. Secure the bass box with the large screw.
.,. Fold the cargo floor back down.
What do I d o now ? 269
Inflatable spare tire
Applies to vehicles: with inflatable spare tire
The inflatable spare tire expands to its full di­
ameter when it is inflated.
Fi g. 21 4 In flatable spa re t ire w it h comp ressor
Removing inflatable spare tire
.,. Lift up the cargo floo r using t he handle .
.,. Remove the dirt t ray .
.,. Turn the large screw
c:!;> fig. 214 co unter­
clockw ise .
.,. Remove the bass box as required
c:!;> page 269 .
.,. Take out the inflatable spare tire .
.,. Always store the vehicle tool kit, the jack*
and the replaced tire in the luggage com ­
partment
c:!;> page 145.
Stowing the inflatabl e spare t ire
.,. Release the air by unscrewing the valve
stem .
.,. Screw the valve stem back in afterwards .
.,. Wait a few hours befo re placing the wheel in
the spare wheel well
c:!;> .,&. .
"'Insta ll the bass box as required c:!;> page 269 .
.,. Secure the wheel with t he la rge screw .
.,. Place the d irt tr ay back in .
.,. Fold the cargo floor back down.
After using the inflatable spare wheel
T he inflatab le spare tire can be re-used as
l ong as it is not damaged and is not wo rn
down to the t read wea r indica tors
c:!;> ,& .
When you let the a ir out of the inflatab le
spare t ire , it does not assume its folded shape
again for s evera l hours . U nti l then , it canno t
be pla ced ba ck in the spare whee l we ll and
stowed secure ly.

2 70 What do I do now?
A WARNING
-Never use the spare tire if it is damaged
or if it is worn down to the tread wear in­
dicators.
- If the inflatable spare tire is more than 6
years old, use it only in an emergency
and with extreme caution and careful
driving.
- The inflatable spare tire is intended only
for temporary and short-term use. It
should be replaced as soon as possible
with the normal wheel and tire.
- The tire pressure value for the inflatable
spare tire is located on the driver's side
8-pillar
¢ page 251, fig. 206.
- Maximum permissible speed is SO mph
(80 km/h).
- Avoid full-throttle acceleration, heavy
braking, and fast cornering .
- When the air is let out of the inflatable
spare wheel, it does not assume its fold­
ed shape for several hours. Until then, it
cannot be placed back in the spare wheel
well and stowed securely.
- Never drive with more than one inflata­
ble spare tire.
- For technical reasons, the use of tire
chains on the inflatable spare tire is not
permitted .
If it is necessary to drive with
tire chains, the inflatable spare wheel
must be mounted on the front axle in the
event of a flat in a rear tire. The newly
available front wheel must then be in­
stalled in place of the rear wheel with
the flat tire. Installing the tire chain be­
fore mounting the wheel and tire is rec­
ommended.
- Loose items in the passenger compart­
ment can cause serious personal injury
during hard braking or in an accident.
Never store the inflatable spare tire or
jack* and tools in the passenger com­
partment.
Q) Note
- The inflatable spare tire has been devel­
oped specifically for this vehicle model.
It must not be exchanged or used for
other vehicle models. Similarly, inflata­
ble tires from other vehicle models must
not be used.
- Normal summer or winter tires must not
be installed on the inflatable tire rim.
Inflating inflatable spare tire
Applies to vehicles : wit h in flatable spa re tire
Fig. 215 L u ggage compartment left side : compressor
.,. Remove the left trim panel in the luggage
compartment.
.,. Open the Velcro strap and remove the com­
pressor ¢
fig. 215.
.,. Unscrew the valve stem from the spare tire.
.,. Screw the tire filler hose from the compres­
sor firmly onto the valve of the spare tire .
.., Insert the plug from the compressor into a
socket of the vehicle
r=;, page 75 .
.., Switch the compressor on.
.., Let the compressor run until the value speci­
fied on the tire pressure label is reached
r=;, page 251, fig. 206. Switch the compres­
sor off after running for 12 minutes at the
most -danger of overheating!
A WARNING
= The compressor and the tire filler hose can
become extremely hot while they are run­
ning -danger of burns!
(D Note
Switch the compressor off after running
for 12 minutes at the most -danger of
overheating! Allow the compressor to cool
down for a few minutes before you use it
again .

(D Note
Special care is required if you are repairing
the tire on a steep incline.
@ Tips
-Do not operate the compressor for more
than 12 minutes continuously, otherwise it can overheat. Once the compressor has
cooled, you can continue to use it.
- If sealant has spilled out, let it dry and
then you can remove it by peeling it away
like a foil.
- Remember to obtain a new bottle of
sealant from your authorized Audi dealer
after repairing a tire. After this, the func­
tionality of the tire repair set is restored.
- Obey all laws.
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang­
ing a wheel.
.,. After you experience a tire failure, pull the
car well away from moving traffic and try to
reach
level ground before you stop¢_& .
.. All passengers should
leave the car and
move to a safe location (for instance, behind
the guardrail) ¢
_&.
.. Engage the parking brake to prevent your
vehicle from rolling unintentionally¢_&.
.. Move
selector lever to position P ¢ _& .
.,. If you are tow ing a trai ler: unhitch the trail­
er from your vehicle.
.,. Block the diagonally opposite wheel with
the folding chocks or other objects.
.. Take the
jack* and the inflatable spare tire*
out of the luggage compartment
¢page 268.
A WARNING
You or your passengers could be injured
while changing a wheel if you do not fol­
low these safety precautions:
-
What do I do now? 273
- If you have a flat tire, move a safe dis­
tance off the road. Turn off the engine,
turn the emergency flashers on and use
other warning devices to alert other mo­
torists.
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traffic.
- To help prevent the vehicle from moving
suddenly and possibly slipping off the
jack*, always fully set the parking brake
and block the wheel diagonally opposite
the wheel being changed with the fold­
ing chocks or other objects. When one
front wheel is lifted off the ground, plac­
ing the Automatic Transmission in P
(Park) will
not prevent the vehicle from
moving.
- Before you change a wheel, be sure the
ground is level and firm. If necessary,
use a sturdy board under the jack*.
- Always store the vehicle tool kit, the
jack* and the replaced tire in the luggage
compartment
¢page 145.
Changing a wheel
When you change a wheel, follow the se­
quence described below step-by-step and in
exactly that order.
1. Remov e the decorative wheel cover*. For
more details see also
¢ page 274, Deco­
rative wheel covers
or ¢ page 2 7 4,
Wheels with wheel bolt cops .
2. Loosen the wheel bolts¢ page 2 75 .
3. Locate the proper mounting point for the
jack* and align the jack* below that point
¢ page 275.
4. Lift the car with the jack* ¢ page 2 75 .
S. Remove the wheel with the flat tire and
then install the
inflatable spare tire*
¢page 276.
6. Tighten all wheel bolts lightly.
7.
Lower the vehicle with the jack*.
8. Use the wheel bolt wrench and
firmly
tighten all wheel bolts¢ page 2 75.
9. Replace the decorative wheel cover*.
•
•

276 What do I do n ow ?
exact ly one location for each whee l. The jack*
must not be positioned at any other location
c::> &. c::> CD .
An un sta bl e s urfa ce under the jac k* can cause
the vehicle to slip off the jack* . Always provide
a firm base for the jack* on the ground. If nec­
essary place a sturdy board or similar support
under the jack*. On
h ard , s lippe ry surfa ces
(such as tiles) use a rubber mat or sim ilar to
prevent the jack* from slipping
c::> &. .
_&. WARNING
-You or your passengers could be injured
wh ile chang ing a wheel if you do not fol­
low these safety precautions:
- Position the jack * only at the designat­
ed lifting points and align the jack *.
Otherwise, the jack* could slip and
cause an injury if it does not have suff i­
cient hold on the vehicle.
- A soft or unstab le surface under the
jack* may cause the vehicle to slip off the jack*. Always provide a firm base
fo r the jack* on the ground . If necessa­
r y, use a st urdy board under the jack*.
- On hard, slippery surface (such as tiles)
use a rubbe r mat o r similar to prevent
the jack* from slipping.
- To help p revent injury to yourself and
yo ur passenge rs:
- Do not raise the vehicle u ntil you are
sure the jack* is securely engaqed.
- Passengers must not remain in the ve­
h icle when it is jac ked up .
- Make sure that passengers wait in a
safe p lace away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct, ad ­
just as necessary and then continue to
ra ise the jack *.
(D Note
Do not lift the vehi cle by the s ill. Position
the jack* only at the des ignated lifting
points o n the sill. Otherwise, your veh icle
wi ll be damaged.
Taking the wheel off /installing the
inflatable spare tire
Follow these instructions step-by-step for
changing the wheel
F ig . 2 23 Chang ing a w hee l: using th e screwdr ive r han­
dle (w ith the blade removed) to turn th e bolts
Fig . 22 4 Cha ng in g a w hee l: alig nment p in ins ide the
top ho le
After yo u have loosened all wheel bo lts and
raised the vehicle off the ground, remove and
replace the wheel as follows:
Removing the wheel
.,. Use the hexagonal so cket in th e screwdriv ­
er handle
to complete ly remove the top­
most whee l bolt and se t it aside on a
clean
surface c::> fig . 223 .
.,. Screw the threaded end of the alignment
pin
from the tool kit hand-t ight into the
empty bolt hole
c::> fig. 224.
.,. Then remove the other wheel bolts as de­
scribed above.
.,. Take off the whee l leaving the a lignment pin
in the bo lt ho le
c::> (D .
Putting on the inflatable spare tire*
.,. Inflate the inflatab le spare tire* c::> page 2 70
and push the wheel over the alignment p in . "'

~ Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel
bo lts
slightly .
~ Remove the alig nment pin and insert and
t igh ten the remaining wheel bolt s light ly
Like t he rest.
~ Turn th e jack handle* counter-clockwise to
l ower the vehicle unti l the jack* is fully re­
leased .
~ Use the whee l bolt w rench to t ighten a ll
whee l bolts firmly <=>
page 2 75. Tighten
them
crosswise, from one bolt to the (ap ­
proximate ly) opposite one, to keep the
whee l centered.
Q;) Note
When removing or installing the wheel,
the rim could hit the brake rotor and dam­
age the rotor. Work carefully and have a
second person help you.
(D} Tips
Never use the hexagonal socket in the han­
dle of the screwdriver to loosen or tighten
the wheel bolts .
- Pull the reversib le b lade from the screw­
driver before yo u use the hexagonal
socket in the handle to t urn the whee l
bo lts .
- When mounting tires with
unid irectional
tread design
make sure the tread pat­
te rn is poi nted the right way
<=> page 2 77.
- The wheel bolts should be clea n and easy
to tu rn . Check for d irt and corrosion on
the mat ing s urfaces of both the wheel
and the hub. Remove a ll dirt from these
su rfaces before remo unting the wheel.
What do I do now? 277
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction .
Using a spa re tire with a tread pattern
intended for use in a specific direction
When using a spare t ire wi th a tread pat ter n
intended for use in a spec ific d irect ion, please
note the fo llowing :
- The d irect io n of rotation is marked by an ar­
row on t he side of the ti re .
- If the spare tire has to be insta lled in the in­
correct d irect ion, use the spare tire only
temporarily s ince the t ire will not be able to
achieve its optimum performance cha racte r­
is tic s w it h regard to aquap la ni ng, no ise and
wear .
- We recommend that you pay part icu lar at­
t en tion to th is f act d uring we t wea ther and
t ha t you adjus t you r speed to m atch r oad
conditions .
- Repla ce the fl at t ire wi th a new o ne and
have i t installed on your vehicle as soo n as
possible to resto re the han dling advantages
of a u nidirectional tire .
Notes on wheel changing
Please read the information¢ page 258, New
tires and replacing tires and wheels
if yo u a re
go ing to use a spare tire w hich is different
from the tires on yo ur vehicle .
After you change a tire:
- Check the tire pre ssure on the spare imme­
diately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon a s
possible by your authorized Audi dealer or
a qualified workshop.
- With steel and alloy wheel rims , the wheel
bolts are cor re ctly tightened at a torque of
105 ft lb (140 Nm).
- If you notice that the wheel bolts are cor­
roded and diff icult to turn while changing
a tire, they should be replaced before you
check the t ightening torque. .,,.
•
•