2014.5 Citroen C4 Owner's Manual

183
Manual operation
D disappears and the gears engaged   appear   in   succession   in  
t

he   instrument   panel.
Invalid value during manual
operation
This symbol is displayed if a gear is   not   engaged   correctly   (selector  
b

etween   two   positions).
Stopping the vehicle
If the lever is not in position P , when the
driver's  d oor  i s  o pened  o r  a pproximately  
4

5   seconds   after   the   ignition   is   switched  
o

ff,   there   is   an   audible   signal   and   a  
m

essage
 ap
pears.
F

R
eturn the lever to position P ;
 
t

he   audible   signal   stops   and   the  
m

essage
 d
isappears.
F

Sel

ect position M for sequential
 c

hanging
 o

f
 
the
 
six
 
gears.
F
 
P

ush
 
the
 
lever
 
towards
 
the
 
+
 
sign
 
to
 
c

hange
 
up
 
a
 
gear.
F
 
P

ull
 
the
 
lever
 
towards
 
the
 
-
 
sign
 
to
 
change
 
d

own
 
a
 
gear.
It
 
is
 
only
 
possible
 
to
 
change
 
from
 
one
 
gear
 
to
 
a

nother
 
if
 
the
 
vehicle
 
speed
 
and
 
engine
 
speed
 p
ermit;
 
other wise,
 
the
 
gearbox
 
will
 
operate
 t
emporarily
 
in
 
automatic
 
mode.
If
 
the
 
engine
 
speed
 
is
 
too
 
low
 
or
 
too
 
high,
 
the
 
g

ear
 
selected
 
flashes
 
for
 
a
 
few
 
seconds,
 
then
 
t

he
 
actual
 
gear
 
engaged
 
is
 
displayed.
It
 
is
 
possible
 
to
 
change
 
from
 
position
 
D
(automatic)
 
to
 
position
 
M
 
(manual)
 
at
 
any
 
time.
When
 
the
 
vehicle
 
is
 
stationary
 
or
 
moving
 
v

ery
 
slowly,
 
the
 
gearbox
 
selects
 
gear
 
M1
automatically.
The
 
sport
 
and
 
snow
 
programmes
 
do
 
not
 
o

perate
 
in
 
manual
 
mode. Before
  switching   off   the   engine,   you   can  
e

ngage   position   P or N   to   place   the   gearbox   in  
neu

tral.
In
 
both   cases,   apply   the   parking   brake   to  
i

mmobilise   the   vehicle,   unless   it   is   programmed  
t

o
 
automatic   mode.
9
Driving

184
When the ignition is on, the lighting   of   this   warning   lamp,  
a

ccompanied   by   an   audible   signal  
a

nd   a   message   in   the   multifunction  
s

creen,   indicates   a   gearbox  
m

alfunction.
Operating fault
You risk damaging the gearbox:
-  i f   you   press   the   accelerator   and  
b

rake   pedals   at   the   same   time,
-
 
i
f  
y
ou  
f
orce  
t
he  
l
ever  
f
rom  
p
osition P
to another position when the
battery
  is   flat.
To
  reduce   fuel   consumption   when  
s

tationary   for   long   periods   with   the  
e

ngine   running   (traffic   jam...),   position  
t

he   gear   lever   at   N   and   apply   the  
p

arking   brake,   unless   it   is   programmed  
i

n   automatic   mode.
In
 
this
 
case,
 
the
 
gearbox
 
switches
 
to
 
back-up
 
m

ode
 
and
 
is
 
locked
 
in
 
3rd
 
gear.
 
You
 
may
 
feel
 
a

 
substantial
 
knock
 
when
 
changing
 
from
 
P
to R
 
and
 
from
 
N to R .
 
This
 
will
 
not
 
cause
 
any
 
d

amage
 
to
 
the
 
gearbox.
Do
 
not
 
exceed
 
60
 
mph
 
(100
 
km/h),
 
local
 
speed
 
r

estrictions
 p

ermitting.
Have
 
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or
 
a
 
q

ualified
 w

orkshop.
This
 
warning
 
lamp
 
may
 
also
 
come
 
on
 
if
 
a
 
door
 
i

s
 ope

ned.
Driving

185
Hill start assist
On an ascending slope, with the vehicle
stationar y, the vehicle is held for a brief
moment when you release the brake pedal:
- 
i
f   you   are   in   first   gear   or   neutral   with   a  
m

anual
 g
earbox,
-
 
i
f   you   are   in   position   A or M with an
electronic
 ge

arbox,
-
 
i
f   you   are   in   position   D or M with an
automatic
  gearbox.
Operation
On a descending slope, with the vehicle
stationary and reverse gear engaged, the
vehicle is held for a brief moment when you
release the brake pedal.
Operating fault
If a fault occurs with the system, these warning lamps   come   on.   Contact   a   CITROËN   dealer  
o

r   a   qualified   workshop   to   have   the   system  
c

hecked.
System
 
which
 
keeps
 
your
 
vehicle
 
immobilised
 
t

emporarily
 
(approximately
 
2
 
seconds)
 
when
 
s

tarting
 
on
 
a
 
gradient,
 
the
 
time
 
it
 
takes
 
to
 
m

ove
 
your
 
foot
 
from
 
the
 
brake
 
pedal
 
to
 
the
 
a

ccelerator
 ped

al.
This
 
function
 
is
 
only
 
active
 
when:
-
 
t

he
 
vehicle
 
is
 
completely
 
stationary,
 
with
 
y

our
 
foot
 
on
 
the
 
brake
 
pedal,
-
 
w

hen
 
certain
 
conditions
 
of
 
gradient
 
are
 
m

et,
-
 
w

ith
 
the
 
driver’s
 
door
 
closed.
The hill start assist function cannot be
deactivated.
Do
 
not
 
leave
 
the
 
vehicle
 
while
 
it
 
is
 
being
 
h

eld
 
in
 
the
 
hill
 
start
 
assist
 
phase.
If
 
you
 
need
 
to
 
leave
 
the
 
vehicle
 
while
 
t

he
 
engine
 
is
 
running,
 
apply
 
the
 
parking
 b
rake
 
manually
 
then
 
ensure
 
that
 
the
 p
arking
 
brake
 
warning
 
lamp
 
is
 
on
 
(not
 
f

lashing)
 
in
 
the
 
instrument
 
panel.
9
driving

186
Gear efficiency indicator*
Depending on the driving situation and your v
ehicle's   equipment,   the   system   may   advise  
y

ou   to   skip   one   (or   more)   gear(s).   You   can  
f

ollow   this   instruction   without   engaging   the  
i

ntermediate
 g
ears.
The
  gear   engagement   recommendations   must  
n

ot   be   considered   compulsory.   In   fact,   the  
c

onfiguration   of   the   road,   the   amount   of   traffic  
a

nd   safety   remain   determining   factors   when  
c

hoosing   the   best   gear.   Therefore,   the   driver  
r

emains   responsible   for   deciding   whether   or   not  
t

o   follow   the   advice   given   by   the   system.
This
  function   cannot   be   deactivated. -
 
Y
ou   press   the   accelerator   pedal.
Example:
-
 Y ou   are   in   third   gear.
-
 
T
he   system   may   suggest   that   you   engage  
a

  higher   gear.
The
  information   appears   in   the   instrument  p
anel   in   the   form   of   an   arrow.
System
  which   reduces   fuel   consumption   by   recommending   the   most   appropriate   gear.
With   an   electronic   or   automatic   gearbox,   the  
s

ystem   is   only   active   in   manual   mode.
*
  Depending   on   engine. On
  vehicle   fitted   with   a   manual   gearbox,  
t

he   arrow   may   be   accompanied   by   the   gear  
re

commended.The
  system   adapts   its   gear   change  
r

ecommendation   according   to   the  
d

riving   conditions   (slope,   load, ...)   and  
t

he   demands   of   the   driver   (power,  
a

cceleration,   braking, ...).
The
  system   never   suggests:
-
 
e
ngaging   first   gear,
-
 enga

ging
 r
everse
 g
ear.
Operation
On BlueHDi Diesel versions with manual gearbox,  t he  s ystem  m ay  s uggest  c hanging  i nto  
n

eutral   so   that   the   engine   can   go   into   standby  
(

STOP   mode   with   Stop   &   Start),   in   certain  
d

riving   conditions.   In   this   case,   N   is   displayed  
i

n   the   instrument   panel.
Driving

187
Tyre under-inflation detection
System which automatically checks the p
ressures   of   the   tyres   while   driving.
The
  system   continuously   monitors   the  
p

ressures of the four tyres, as soon as the
vehicle
  is   moving.
A
  pressure   sensor   is   located   in   the   valve   of  
e

ach   tyre   (except   the   spare   wheel).
The
  system   triggers   an   alert   if   a   drop   in  
p

ressure   is   detected   in   one   or   more   tyres.
The
  tyre   under-inflation   detection   system   is   an  
a

id   to   driving   which   does   not   replace   the   need  
f

or   vigilance   on   the   part   of   the   driver.This
  system   does   not   avoid   the   need  
t

o   check   the   tyre   pressures   regularly  
(

including   the   spare   wheel)   and   before  
a

  long   journey.
Driving   with   under-inflated   tyres  
a

dversely   affects   road   holding,  
e

xtends   braking   distances   and   causes  
p

remature   tyre   wear,   particularly   under  a
rduous   conditions   (vehicle   loaded,  h
igh   speed,   long   journey).The tyre pressures for your vehicle can
be
  found   on   the   tyre   pressure   label   (see  
t

he   "Identification   markings"   section).
The   tyre   pressures   must   be   checked  
w

hen   the   tyres   cold   (vehicle   stopped  
f

or   1   hour   or   after   driving   for   less   then  
6

  miles   (10   km)   at   moderate   speed).  
O

ther wise,   add   0.3   bar   to   the   values  i
ndicated   on   the   label.
Driving   with   under-inflated   tyres  
i

ncreases   fuel   consumption.
9
driving

188
The flashing and then fixed illumination   of   the   under-inflation w

arning   lamp   accompanied   by   the
 i

llumination   of   the   service   warning
 l

amp   indicates   a   fault   with   the   system.
Operating fault
The aler t  is  given  by  the  fixed  illumination o
f   this   warning   lamp,   accompanied   by a

n   audible   signal,   and   depending   on
 e

quipment,   the   display   of   a   message.
Under-inflation alert
In the event of a problem on one of the tyres, the   symbol   or   the   message   appears,   according  
t

o   equipment,   to   identify   it.
F
 
R
educe   speed,   avoid   sudden   steering  
m

ovements   or   harsh   brake   applications.
F
 
S
top   as   soon   as   it   is   safe   to   do   so. In
  this   case,   monitoring   of   the   tyre   pressures   is  
n

ot   assured.
F  
I
f   you   have   a   compressor   (the   one   in   the  
t

emporary   puncture   repair   kit   for   example),  
c

heck   the   four   tyre   pressures   when   cold.
 I

f   it   is   not   possible   to   check   the   tyre  
p

ressures   at   the   time,   drive   carefully   at  
r

educed
 s
peed.


or
F
I
n the event of a puncture, use the
temporary   puncture   repair   kit   or   the   spare  
w

heel   (according   to   equipment).
Go   to   a   CITROËN   dealer   or   a   qualified  w
orkshop to   have   the   system   checked   or,  
f

ollowing   the   repair   of   a   puncture,   to   have   the  
o

riginal   wheel,   equipped   with   a   sensor,   refitted.
Any
  tyre   repair   or   replacement   on   a   wheel  
f

itted   with   this   system   must   be   carried   out   by   a  
C

ITROËN   dealer   or   a   qualified   workshop.
If
  after   changing   a   tyre,   a   wheel   is   not   detected  
b

y   your   vehicle   (fitting   snow   tyres   for   example),  
y

ou   must   have   the   system   reinitialised   by   a  
C

ITROËN   dealer   or   a   qualified   workshop.
The
  loss   of   pressure   detected   does   not  
a

lways   lead   to   visible   deformation   of   the  
t

yre.   Do   not   rely   on   just   a   visual   check.This
  alert   is   also   displayed   when   one   or  
m

ore   wheels   is   not   fitted   with   a   sensor  
(

for   example,   a   space-saver   or   steel  
spar

e
 w
heel).
The   alert   is   maintained   until   the   tyre   or  t
yres   concerned   is   reinflated,   repaired  
o

r   replaced.
The
  spare   wheel   (space-saver   type   or   a  
s

teel   rim)   does   not   have   a   sensor.
Driving

189
Stop & Start
Operation
Going into engine STOP mode
The "ECO"  warning   lamp   comes   on i
n   the   instrument   panel   and   the   engine g

oes   into   standby   automatically:
-
 
w

ith a manual gearbox ,
  at   speeds   below  
1

2
 
m

ph  
(
20  
k
m/h),  
o
r  
v
ehicle  
s
tationary  
w
ith  
P

ureTech   130   petrol   and   BlueHDi   Diesel  
v

ersions,   when   you   put   the   gear   lever   into  
n

eutral   and   release   the   clutch   pedal,
If
  your   vehicle   is   fitted   with   the
 s

ystem,   a   time   counter   calculates
 t

he   sum   of   the   periods   in   STOP
 m

ode   during   a   journey.   It   resets
 i

tself   to   zero   every   time   the
 i

gnition   is   switched   on   with   the
 k

ey   or   the   "START/STOP"   button.
-
 
w

ith an electronic gearbox ,
  at   a   speed  
b

elow   5   mph   (8   km/h),   when   you   press  
t

he
 
brake   pedal   or   put   the   gear   lever   into  
p

osition N .
Special cases: STOP mode
unavailable
STOP mode is not invoked when:
-  t he   vehicle   is   on   a   steep   slope   (up   or  
d

ow n),
-
 
t
he   driver's   door   is   open,
-
 
t
he   driver's   seat   belt   is   not   fastened,
-
 
t
he   vehicle   has   not   exceeded   6   mph  
(

10 km/h)   since   the   last   engine   start   (using  
t

he   key   or   the   "START/STOP"   button),
-
 
t
he   electric   parking   brake   is   applied   or  
be

ing
 a
pplied,
-
 
t
he   engine   is   needed   to   maintain   a  
c

omfortable   temperature   in   the   passenger  
c

ompartment,
-
 
d
emisting   is   active,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
In this case, the "ECO"
 

warning   lamp  
f

lashes   for   a   few   seconds,   then  
goes
  off.
This operation is perfectly normal.
The
 
Stop
 
&
 
Start system
 
puts
 
the
 
engine
 
temporarily
 
into
 
standby
 
-
 
STOP
 
mode
 
-
 
during
 
stops
 
in
 
the
 
traffic   (red   lights,   traffic   jams,   or   other...).  
The
 
engine
 
restarts
 
automatically
 
-
 
START
 
mode
 
-
 
as
 
soon
 
as
 
you
 
want
 
to
 
move
 
off.
 
The
 
restart
 
takes
 
place   instantly,   quickly   and   silently.
Per fect
 
for
 
urban
 
use,
 
the
 
Stop
 
&
 
Start
 
system
 
reduces
 
fuel
 
consumption
 
and
 
exhaust
 
emissions
 
as
 
well
  as   the   noise   level   when   stationary.
Never
 
refuel
 
with
 
the
 
engine
 
in
 
STOP
 
m

ode;
 
you
 
must
 
switch
 
off
 
the
 
ignition
 
w

ith
 
the
 
key
 
or
 
the
 
"START/STOP"
 
b

utton.
With
 
an
 
electronic
 
gearbox,
 
for
 
your
 
c

omfort
 
during
 
parking
 
manoeuvres,
 
S

TOP
 
mode
 
is
 
not
 
available
 
for
 
a
 
few
 
s

econds
 
after
 
coming
 
out
 
of
 
reverse
 
g

e a r.
STOP
 
mode
 
does
 
not
 
affect
 
the
 
f

unctionality of the vehicle, such as
braking,
 
power
 
steering,
 
for
 
example.
9
driving

190
Deactivation
Going into engine START mode
At any time, press the "ECO OFF" switch to
d eactivate   the   system.
This
  is   confirmed   by   the   switch   warning   lamp  
c

oming   on   accompanied   by   the   display   of   a  
m

essage.
Special cases: START invoked
automatically
The "ECO"  warning   lamp   goes   off  a
nd   the   engine   starts   automatically:
-
 
w

ith a manual gearbox , when you fully
depress
  the   clutch   pedal,
-
 
w

ith an electronic gearbox :
●
 
g

ear   lever   in   position   A or M, when you
release
  the   brake   pedal,
●
 
o

r
 
gear   lever   in   position   N   and   the   brake  
p

edal   released,   when   you   move   the   gear  
l

ever to position A or M ,
●
 
o

r
 
when   you   engage   reverse   gear.For
  safety   reasons   or   to   ensure   smooth  o
peration,   START   mode   is   invoked  
a

utomatically
 w
hen:
-
 
y
ou   open   the   driver's   door,
-
 
y
ou   unfasten   the   driver's   seat   belt,
-
 
t
he   speed   of   the   vehicle   exceeds   15 mph  
(

25   km/h)   with   a   manual   gearbox   (3 km/h  
(

2   mph)   with   PureTech   130   petrol   and  
B

lueHDi   Diesel   versions)   or   7   mph  
(

11 km/h)   with   an   electronic   gearbox,
-
 
t
he   electric   parking   brake   is   being   applied,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
In this case the "ECO"
 

warning   lamp  
f

lashes   for   few   seconds,   then  
goes
  off.
This operation is perfectly normal.
With
  a   manual   gearbox   in   STOP   mode,  
i

f
 
a
  gear   is   engaged   without   fully  
d

epressing   the   clutch   pedal,   a   warning  
l

amp   comes   on   or   an   alert   message  
i

s
 
displayed   asking   you   to   depress   the  
c

lutch   pedal   to   restart   the   engine. If
  the   system   has   been   deactivated  
i

n   STOP   mode,   the   engine   restarts  
i

mmediately.
Driving