2013 YAMAHA RHINO 700 light

4-3
EVU00170Neutral indicator light “N”
This indicator light comes on when the drive
select lever is in the “N” position.5B410001Reverse indicator light “R”
This indicator light comes on when the drive
select lever is in the “R” position.EVU00210Parking brake indicator light “P”
This indicator light comes on when the park-
ing brake is applied.
EBU29621On-Command four-wheel-drive indicator
“ ”, On-Command differential gear lock
indicator “ ” and indicator light “DIFF.
LOCK”
The On-Command four-wheel-drive indicator
“ ” comes on when the On-Command four-
wheel-drive switch is set to the “4WD” posi-
tion.
The On-Command differential gear lock indi-
cator “ ” and the On-Command differential
gear lock indicator light “DIFF. LOCK” come
on when the On-Command differential gear
lock switch is set to the “LOCK” position.
DIFF.
LOCK
DIFF.
LOCK
1RB7A_EE.book Page 3 Tuesday, April 24, 2012 9:07 AM

4-4
TIP●
Due to the synchronizing mechanism in
the differential gear case, the four-wheel-
drive indicator may not come on until the
Rhino starts moving.
●
When the On-Command differential gear
lock switch is set to “LOCK” or “4WD”, the
indicator “ ” and the indicator light
“DIFF. LOCK” will flash until the differen-
tial gear is completely locked or un-
locked. If the indicator and the indicator
light continue to flash, the differential is
not completely locked or unlocked. In this
case, start moving to allow time for the
differential to lock or unlock.
5B410002Coolant temperature warning light “ ”
If the coolant temperature reaches a specific
level, this light comes on to warn that the cool-
ant temperature is too hot. If the light comes
on during operation, stop the engine as soon
as it is safe to do so and allow the engine to
cool down for about 10 minutes.
(See page 8-62.)
The electrical circuit of the warning light can
be checked by turning the key to “ON”. If the
warning light does not come on initially when
the key is turned to “ON”, or if the warning light
remains on, have a Yamaha dealer check the
electrical circuit.
DIFF.
LOCK
1RB7A_EE.book Page 4 Tuesday, April 24, 2012 9:07 AM

4-5
NOTICE●
The engine may overheat if the vehicle
is overloaded. If this happens, reduce
the load to specification.
●
After restarting, make sure that the
warning light is out. Continuous use
while this warning light is on may
cause damage to the engine.
5B410003Engine trouble warning light “ ”
This warning light comes on or flashes if a
problem is detected in the electrical circuit
monitoring the engine. When this occurs,
have a Yamaha dealer check the self-diagno-
sis system. (See pages 4-11–4-12 for an ex-
planation of the self-diagnosis device.)
The electrical circuit of the warning light can
be checked by turning the key to “ON”. If the
warning light does not come on initially when
the key is turned to “ON”, or if the warning light
remains on, have a Yamaha dealer check the
electrical circuit.
1RB7A_EE.book Page 5 Tuesday, April 24, 2012 9:07 AM

4-6
Helmet/seat belt indicator light “ / ”1. Helmet/seat belt indicator light “ / ”The indicator light comes on when the key is
turned to “ON” to remind the occupants to al-
ways wear a helmet and to fasten their seat
belt. The indicator light stays on even when
the seat belt is properly latched.
If the indicator light does not come on when
the key is turned to “ON”, have a Yamaha
dealer check the electrical circuit.
5B410004*Multi-function meter unit1. Speedometer 2. Fuel meter
3. “H” button 4. “M” button
5. Clock/Hour meter/Voltage display
6. Odometer/Tripmeter A/Tripmeter B
7. “TRIP/ODO” button 8. Clock/Hour button “ / ”The multi-function meter unit is equipped with
the following:●
a speedometer
●
an odometer
123
4
5
6
7 8
1RB7A_EE.book Page 6 Tuesday, April 24, 2012 9:07 AM

4-11
TIPThis fuel meter is equipped with a self-diagno-
sis system. If a problem is detected in an elec-
trical circuit, all the display segments and fuel
level warning indicator start flashing. If this oc-
curs, have a Yamaha dealer check the electri-
cal circuit.
Self-diagnosis device1. Engine trouble warning light “ ”
2. Error code displayThis model is equipped with a self-diagnosis
device for various electrical circuits.
If a problem is detected in any of those cir-
cuits, the engine trouble warning light comes
on or flashes, and the multi-function display
indicates an error code.
If the multi-function display indicates an error
code, note the code number, and then have a
Yamaha dealer check the vehicle.
2
1
1RB7A_EE.book Page 11 Tuesday, April 24, 2012 9:07 AM

4-12
NOTICEIf the multi-function display indicates an
error code, the vehicle should be checked
as soon as possible in order to avoid en-
gine damage.
EVU00240Light switch “OFF/ / ”1. Light switch “OFF/ / ”Set the switch to “ ” to turn on the low beam
and the taillights.
Set the switch to “ ” to turn on the high
beam and the taillights.
Set the switch to “OFF” to turn off the head-
lights and taillights.
L
H
L
HL
H
1RB7A_EE.book Page 12 Tuesday, April 24, 2012 9:07 AM

4-13
NOTICEDo not use the headlights with the engine
turned off for an extended period of time.
The battery may discharge to the point
that the starter motor will not operate
properly. If this should happen, remove
the battery and recharge it.
EVU01183On-Command four-wheel-drive and differ-
ential gear lock switches1. On-Command four-wheel-drive switch “2WD”/“4WD”
2. On-Command differential gear lock switch “4WD”/“LOCK”This vehicle is equipped with an On-Com-
mand four-wheel-drive switch “2WD”/“4WD”
and a differential gear lock switch “4WD”/
“LOCK”. Select the appropriate drive accord-
ing to terrain and conditions.●
“2WD” (two-wheel drive): Power is supplied
to the rear wheels only.
1RB7A_EE.book Page 13 Tuesday, April 24, 2012 9:07 AM

4-36
EVU00370Trailer hitch bracket and receiver
This vehicle is equipped with a trailer hitch
bracket and a 5 cm (2 in) receiver for a stan-
dard trailer hitch. Trailer towing equipment
can be obtained at a Yamaha dealer. (See
pages 6-9–6-11 for precaution information.)1. Trailer hitch bracket 2. Receiver
EVU00380Auxiliary DC jack
The auxiliary DC jack is located at the right
side of the front panel. The auxiliary DC jack
can be used for suitable work lights, radios,
etc. The auxiliary DC jack should only be used
when the engine is running and the headlights
are turned off.1. Auxiliary DC jack cap1. Set the light switch to “OFF”.
2. Turn the accessory off.
3. Start the engine. (See pages 6-2–6-3.)
2
1
1RB7A_EE.book Page 36 Tuesday, April 24, 2012 9:07 AM