2013 YAMAHA RHINO 700 oil dipstick

3-1
1
23
4
5
6
7
8
9
10
11
12
13
14
EVU00080
1-DESCRIPTION
1. Headlights
2. Front shock absorber assembly
3. Brake fluid reservoir
4. Air filter element
5. V-belt case
6. Driver seat
7. Driver seat belt
8. Cargo bed
9. Tail/brake lights
10. Rear shock absorber assembly
11. Cargo bed release levers
12. Spark plug
13. Door 14. Spark arrester
15. Passenger seat belt
16. Sun top (YXR7FSPD)
17. Passenger seat
18. Passenger handholds
19. Engine oil dipstick
20. Battery
21. Fuses
22. Coolant reservoir
23. Radiator cap
24. Oil filter cartridge
25. Fuel tank cap
CBA 089
IHGF
EJKLM
AC
NO
D
1RB7A_EE.book Page 1 Tuesday, April 24, 2012 9:07 AM

8-10
5B410012Engine oil and oil filter cartridge
Check engine oil level before each operation.
In addition, change the oil and the oil filter car-
tridge at the intervals specified in the periodic
maintenance and lubrication chart.
To check the engine oil level1. Park the vehicle on a level surface.
2. Remove the console. (See page 8-9 for console removal and installation proce-
dures.)
3. Check the engine oil level on a cold en-
gine. TIPIf the engine was started before checking the
oil level, be sure to warm up the engine suffi-
ciently, and then wait at least 10 minutes until
the oil settles for an accurate reading.4. Remove the engine oil dipstick, and thenwipe it off with a clean rag.
1. Engine oil dipstick
1
1RB7A_EE.book Page 10 Tuesday, April 24, 2012 9:07 AM

8-11
5. Insert the dipstick completely into the oilfiller hole, and then remove it again to
check the oil level. TIPThe engine oil should be between the mini-
mum and maximum level marks.1. Maximum level mark 2. Minimum level mark6. If the engine oil is at or below the mini-mum level mark, add sufficient oil of the
recommended type to raise it to the cor-
rect level. 7. Insert the dipstick completely into the oil
filler hole.
8. Install the console.
1
2
1RB7A_EE.book Page 11 Tuesday, April 24, 2012 9:07 AM

8-12
To change the engine oil (with or without
oil filter cartridge replacement)1. Park the vehicle on a level surface.
2. Remove the console. (See page 8-10 for
console removal and installation proce-
dures.)
3. Start the engine, warm it up for several minutes, and then turn it off.
4. Place an oil pan under the engine to col-
lect the used oil, and then remove the
dipstick.
5. Remove the engine oil drain bolt and its
gasket to drain the oil from the crank-
case.
1. Engine oil drain bolt 2. GasketTIPSkip steps 6–10 if the oil filter cartridge is not
being replaced.6. Lift the cargo bed up. (See pages 4-22– 4-23 for cargo bed lifting and lowering
procedures.)
2
1
1RB7A_EE.book Page 12 Tuesday, April 24, 2012 9:07 AM

8-14
1. Oil filter cartridge 2. Torque wrench
10. Lower the cargo bed.
11. Install the engine oil drain bolt and its
new gasket, and then tighten the bolt to
the specified torque. 12. Refill with the specified amount of recom-
mended engine oil, and then insert the
dipstick completely into the oil filler hole.
TIPBe sure to wipe off spilled oil on any parts af-
ter the engine and exhaust system have
cooled down.
Tightening torque:Engine oil drain bolt: 30 Nm (3.0 m·kgf, 22 ft·lbf)
1
2
Recommended engine oil: See pages 10-1–10-2.
Oil quantity: Without oil filter cartridge replacement:
2.00 L (2.11 US qt, 1.76 Imp.qt)
With oil filter cartridge replacement: 2.10 L (2.22 US qt, 1.85 Imp.qt)
1RB7A_EE.book Page 14 Tuesday, April 24, 2012 9:07 AM