2013 SSANGYONG TURISMO turn signal

02-34
▶Auto Door Lock
The door lock system outputs "LOCK" when the vehicle speed maintains over 50 km/h. However, it
doesn't output "LOCK" when all doors are locked or failed.
If any of doors is unlocked after outputting "LOCK" in step 1, outputs "LOCK" up to 5 times (except
step (1)) at the interval of one second.
If any of doors is unlocked after 5 times of "LOCK" outputs, the door(driver's/passenger's/
rear) is regarded as "FAIL".
If the door that was regarded as fail is changed(UNLOCK to LOCK), it will be recognized as a
normal one.
If any door is regarded as FAIL, the auto door lock function does not work. (if it is occurred when the
vehicle speed is over 50 km/h, the auto door lock output does not occur even if the vehicle speed
falls below 50 km/h and accelerates again to over 50 km/h.) Nonetheless, the central door lock
function works properly.
When the system receives "UNLOCK" signal from a door switch, it outputs "LOCK" signals 5 times.
If additional "LOCK" signal from another door switch is detected during the period, the system
outputs five "LOCK" signals 5 times for the switch.
The door lock system outputs "UNLOCK" automatically if the "LOCK" output conditions are
established by this function or the key is cycled(IGN=OFF) (even when there is no "LOCK" output
while the vehicle speed maintains over 50 km/h under lock condition). (If the LOCK condition is
established with the ignition switch ON, the system outputs UNLOCK signal unconditionally when
turning the ignition switch to OFF position.) However, when the ignition key is turned to "OFF"
position, the lock output conditions will be cancelled.
The "FAIL" condition of the door will be erased when the ignition key is turned to "OFF" position. 1.
2.
3.
4.
5.
6.
7.
8.

02-358710-01
▶Auto Door Unlock (Crash Unlock)
The air bag collision signal input cannot be accepted within 7 seconds after turning the ignition key
to "ON" position.
After this period, the door lock system outputs "UNLOCK" for all doors for 5 seconds from 40 ms
after receiving the air bag collision signal.
Even though the key is turned to "OFF" position during the output of "UNLOCK", the output
continues on for remaining period.
The function is erased when turning "OFF" the ignition switch. 1.
2.
3.
4.
The "Unlock" control by air bag signal prevails over any "LOCK" or "UNLOCK" control by other
functions.
The "LOCK/UNLOCK" request by other functions will be ignored after/during the output of
"UNLOCK" by the air bag. However, the door lock is controlled by other functions when the
ignition switch is "OFF".
"LOCK" (or "UNLOCK") output is ignored if "LOCK" (or "UNLOCK") output is required while
performing the output of "LOCK" (or "UNLOCK"). (However, UNLOCK by air bag signal and
operation by the remote control key are valid.)
If the door lock system outputs "LOCK" and "UNLOCK" simultaneously, only the "LOCK" output
can be activated. 1.
2.
3.
4.

02-378710-01
13) Theft Deterrent
(1) Description of Burglar Alarm Function
The “LOCK” output is “ON” when receiving the “LOCK” signal from transmitter while the
ignition key is removed and all doors are closed. The armed mode is activated when the door lock
switch is locked (theft deterrent horn output: once, hazard relay output: twice).
The theft deterrent horn and hazard relay outputs are “ON” when receiving the “LOCK” signal
from the remote control key again in armed mode (theft deterrent horn output: once, hazard relay
output: twice).
When receiving “LOCK” signal from the remote control key while any of doors is not closed,
only the “LOCK” output can be done and then activates the armed ready mode (without theft
deterrent horn and hazard warning flasher). At this moment, if the ignition key is in the ignition switch,
the door unlock switch is turned “ON” or the door lock switch is unlocked (after 0.6 seconds),
cancels the armed mode and activates the normal mode. However, in these cases, if closing the
door and locking the door lock switch, the theft deterrent horn outputs once and the hazard warning
flasher outputs twice and then activates armed mode.
When the door is not opened or the ignition key is not inserted into ignition switch for 30 seconds
after receiving “UNLOCK” signal, outputs “LOCK” and then activates armed mode (RELOCK
operation). Also, at this moment, the system outputs the theft deterrent horn and hazard warning
flasher.
The armed mode will not be activated except above conditions.
Ex) The armed mode will not be activated when the door is locked by the ignition key. 1.
2.
3.
4.
5.
▶Theft deterrent mode ON conditions

02-38
▶Armed mode cancellation requirements
Unlocking by remote control key or engine starting. 1.
▶Warning operation requirements
When opening the door in armed mode
When unlocking the door lock switch in armed mode
When closing and then opening the door after completion of warning (27 seconds) 1.
2.
3.
▶Warning operation
The theft deterrent horn and hazard warning flasher output is “ON” for T3 (27 seconds)
with the interval of T2 (1second). 1.
▶Warning cancellation requirements
Cancels warning by using any signal from the remote control key (LOCK, UNLOCK, START,
STOP, PANIC, CHECK) during warning operation.
Cancels warning after 27 seconds (remaining period) while the ignition key is turned to
“ON” position. 1.
2.
▶Operation when warning is cancelled
The theft deterrent horn and hazard warning flasher outputs are “OFF”. 1.

02-398710-01
The PANIC warning output is “ON” (theft deterrent horn) when receiving the PANIC signal
from the remote control key (pressing PANIC button for less than 0.5 ~ 1.0 second).
The PANIC warning output is “OFF” when receiving any signal from the remote control key
during PANIC warning.
Followings are theft deterrent warnings:
This function operates only in armed mode.
The system sends the current vehicle conditions (LOCK, engine running) when the PANIC warning
is turned off by the remote control key. 1.
2.
3.
4.
5.The theft deterrent warning is canceled when receiving PANIC signal from the remote control key
during theft deterrent.
The theft deterrent warning output is “ON” when the theft deterrent conditions are
established during PANIC warning (PANIC output is “OFF”).
The PANIC warning output is “ON” when receiving the PANIC signal from the remote
control key in Armed Ready / Armed / Warning Completion / Relock Ready mode (maintaining
the theft deterrent mode). 1)
2)
3)
(2) PANIC Warning

03-97010-06
ECU
Immobilizer Indicator and Warning Lamp ▶
This indicator comes on when the ignition
key is communicating with the engine control
unit (during engine starting) and goes out
after starting the engine.
When turning the ignition key to ON position, the
ECU transmits the challenge message to the
immobilizer unit to verify whether the key is valid. (1)
Only when the two signals are identical, it
recognizes the key as the authorized one and
transmits the positive message to the ECU.
The ECU allows the engine to be started. (6)
(7)
Do not drop or shock to the transponder in the key as it may be damaged.
With a damaged transponder, the engine cannot be started.
When you erase the code or register an extra key, let the owner attend on the site.
In any case, the immobilizer system cannot be removed from the vehicle. If you attempt to
remove it and damage the system, starting will be impossible, so never attempt to remove,
damage or modify it.
The remote engine starter cannot be installed on the vehicle equipped with the immobilizer
system. -
-
-
-
-Lamp ON: in communication
Blinking twice for one second:
immobilizer system failure
Blinking once for two seconds:
immobilizer unit is not coded
The immobilizer indicator does not come
on if the communication time between
immobilizer key and ECU is too short.
Immobilizer Indicator and Warning Lamp

07-38310-01
1. BULB SPECIFICATIONS
Description AmountSpecification
(EU)Specification
(General)
Exterior
lampHeadlamp High beam + DRL 2 55W + 15W 55W
Low beam 2 55W←
Turn signal lamp 2 21W←
Position lamp 2 5W←
Front fog lamp 2 H16←
Side repeater 2 5W←
Rear
combination
lampTail (stop) lamp 4 5W(21W)←
Turn signal lamp 2 21W←
Back-up lamp 2 16W←
Rear fog lamp 2 21W -
License plate lamp 2 5W←
High mounted stop lamp 5 5W←
Interior lamp Front room lamp 2 5W←
Glove box lamp 1 5W←
Door courtesy lamp 4 5W←
Side room lamp 4 5W←
Rear room lamp 1 5W←

07-4
Front fog lamp
Fog lamp design changed
Headlamp
Design and function changed
2. MAJOR CHANGES
1) Exterior Lamp
Front view ▶
Headlamp
Tail lamp (12V-5W)
Turn signal lamp
(12V-28W)Low beam
(12V-55W)High beam
(12V-55W)Low beam
(H7-55W)
Tail lamp (W5W)Turn signal
lamp (P21W)
High beam + DRL
(EU: 55W+15W, GEN: 55W)
Front fog lamp
Headlamp
Front fog lamp