2013 SSANGYONG TURISMO sensor

02-16
▶INT Switch Auto Position Reminder (Power-Up Reminder Wiper)
When turning off and on the auto INT switch, the system drives the wiper motor through LOW
relay regardless of communication with rain sensor.
When turning the INT-AUTO switch from the "OFF" to "ON" position with the ignition switch in
the "ON" mode, the LOW relay operates to drive the wiper motor for 1 cycle, regardless of the
rain sensor communication.
After that, when turning the INT-AUTO switch from the "OFF" to "ON" position, the LOW relay
operates to drive the wiper motor for 1 cycle only if data from the rain sensor indicates rain
drops. 1.
2.

06-58510-00
2. MAJOR CHANGES
Center fascia switch
- Design changed
Steering wheel switch assembly
- Power button deleted, steering wheel heating (option) switch added
- Design changed
Multifunction switch assembly
- Connector pin layout changed due to newly added steering wheel heating (option) circuit
- Contact coil and steering wheel angle sensor changed

06-8
Outside Rearview
Mirror Adjusting/
Folding Switches
Window switch
Steering Wheel Audio/Heating Switch & Gear Shift Switch (A/T)
Multifunction Switch and Steering
Wheel Angle Sensor
4WD Switch, Headlamp
Leveling Switch, Rear Wiper
Switch
1. LAYOUT
Seek button
Volume button Manual gear shift down
switchManual gear shift up switch
Mode button
Bluetooth handsfree
Steering wheel heating switch
With audio OFF: press the MUTE
button briefly to switch on
With audio ON: press and hold the
MUTE button to switch off
MUTE button -
-
-

06-98510-00
Center fascia switch
Passenger’s Window Switch
(same with rear window
switches)
Overhead console switch
Auto light sensor
Cigarette lighter
Power outlet socket
Driver’s seat
warmer switch
Rear fog lamp
switchESP OFF switch
Defogger switch
Passenger’s seat
warmer switch Front fog lamp switch
Front room lamp switch
Sunroof switch
Door coupled room lamp switch
Hazard warning
flasher switch

07-4
2. CAUTIONS ON RAIN SENSOR
When the wiper switch is in the AUTO position, the wiper will operate for 1 cycle if the initial engine
start is made. This may cause the wiper blades to wear prematurely. Therefore, other than rainy
days, set the switch to the OFF position. Especially during the winter time, check if the wiper blades
are not frozen to the windshield.
Operating the wiper with the blades frozen can damage the wiper motor.
If you operate the wipers when the windshield is dry without spraying washer fluid, the windshield can
be scratched and the wiper blades can wear prematurely. Use the wiper with the washer fluid when
the windshield is dry.
When it does not rain, turn the wiper switch to the OFF position.
Turn the wiper switch to the OFF position before any car wash to avoid unwanted operation of the
wipers. -
-
-
-
When cleaning the windshield over the sensor with damp clothes, the wiper may operate suddenly.
It could cause serious injury. Make sure to place the wiper switch to the OFF position and ignition
switch OFF when not in use.
Irregular operation (abrupt operation) ▶
Check if the sensor is off the position.
Check if the rain sensor cover is securely installed.
Check if the customer is familiar to how to control the wiper sensitivity.
Check if the wiper sensitivity control is set to the FAST side (step 5).
Check the wiper blade for wear.
If the wiper blade cannot wipe the glass uniformly and clearly, it may cause the rain sensor to work
irregularly. Therefore, in this case, replace the wiper blade with a new one. -
-
-
-

07-57810-01
Rear Wiper Motor
Motor mounting bracket changed due to
change of tailgate
Front wiper blade
Before: Conventional type(driver: 600 mm, front passenger: 450 mm)
After: Aero blade type(driver: 600 mm, front passenger: 450 mm)
3. MAJOR CHANGES IN WIPER & RAIN SENSOR SYSTEM
Front view ▶
Rear view ▶
Rear wiper blade
Wiper arm design changed; no change in
wiper blade dimension

08-38610-11
The rain sensing wiper unit in this vehicle doesn’t control the wiper directly.
The rain sensing unit detects the amount of rain drops and sends the operating signal to STICS, and
STICS drives the wiper directly.
1. SYSTEM LAYOUT AND OVERVIEW
Rain sensing unitMultifunction wiper switch:
AUTO and sensitivity control
A sensor that emits infrared rays through LED
and then detects the amount of rain drops by
receiving reflected rays against sensing
section(rain sensor mounting section on the
windshield)with photodiode. AUTO
: Wiper operates automatically by rain sensor
FAST <-------> SLOW
: Auto delay/Auto speed control. A position
that can control sensitivity against rains on
the windshield and transmits wiping demand
signal accordingly.
Emitter lens
The LED which is located
at bottom emits the
infrared rays and the lens
guides the infrared rays to
target point.
Enlarged auto light
sensor section
Auto light sensor
Auto light sensor (Horizon)
Auto light sensor (Vertical)

08-4
ICM box
The wiper related relays are installed in
ICM box.
Relay5
(Wiper INT-Low)Relay6
(Wiper High)
STICS
The rain sensing unit detects the amount of rain drops and sends the
operating signal to STICS, and STICS drives the wiper directly.
At this moment, STICS determines the wiper operation mode
(washer, MIST, AUTO), then sends the information to the rain
sensor.