2013 SSANGYONG TURISMO door lock

01-6
D20DTR
Diesel Engine: The engine number is
stamped on the lower area of cylinder
block behind the Intake manifold.
Visual VIN LabelEngine Number
Gasoline Engine: The
engine number is stamped
on the lower area of cylinder
block in exhaust manifold
side.VIN Number
The VIN number is stamped
on the floor under the
passenger’s mat.
Certification Label
The certification label is
located on the driver’s
door sill.
3. VEHICLE IDENTIFICATION

02-18
This function does not work if the vehicle speed is over 3 km/h.
The system outputs “UNLOCK” for 5 seconds (T2) from 0.5 seconds after the driver’s door
is opened and the door lock switch is changed to “LOCK” (while the ignition key is in ignition
switch).
The system outputs “UNLOCK” for 5 seconds (T2) when the door lock switch is changed to
“LOCK” from “UNLOCK” and the driver’s door is closed within 0.5 seconds (T1) (while the
ignition key is in ignition switch). 1.
2.
3. ▶Key Reminder
Operating conditions for (*1) and (*2) -
(*1): Driver’s door is opened and driver’s door lock switch is turned to LOCK
(*2): Passenger’s door is opened and passenger’s door lock switch is turned to LOCK

02-198710-01
▶All Door Lock Prevention Function when a Door is Opened
When a door is opened, all doors should be unlocked for 5 seconds if inputs LOCK signal. 1.
The LOCK signal means the central door locking (REKES, central door lock switch, knob switch)
except LOCK input by rear door knob.
After unlocking and opening only the driver’s door with remote control key under armed
mode (driver’s door is unlocked but passenger’s and rear doors are locked), only the
driver’s door generates unlock signal when trying to lock the driver’s door with the driver’s
door opened.
Above operations is regardless of key positions and have priority over the ignition key reminder
function. -
-
-
When the door is closed during unlock output for 5 seconds under item 1 condition, the unlock
output stops. 2.
All doors except tailgate and hood output “UNLOCK” for 5 seconds (T1) when the “LOCK”
signal is inputted (while the ignition key is removed and a of door is opened).
When the door is closed during unlock output for 5 seconds, the unlock output stops. -
-

02-20
3) Mark Lamp Left on Warning
The chime buzzer in the ICM box sounds with the interval of 0.8 second when opening the
driver’s door while the tail lamp is turned on and the ignition key is removed.
The buzzer output stops when turning off the tail lamp and closing the driver’s door.
The system outputs “UNLOCK” for 5 seconds when the driver’s and passenger’s door lock
switch is locked (while the tail lamp is turned on and the driver’s door is opened).
This function is not available when the ignition key is in “ON” position. 1.
2.
3.
4.

02-24
7) Room Lamp Control
▶ Front Room Lamp
The front room lamp comes on when opening the
driver’s door or passenger’s door while the front
room lamp switch is at door coupled position and the
key reminder switch is turned off.
The room lamp stays on for 2 seconds (T1) and then
decays through 3 seconds (T2) when closing the
driver’s door or passenger’s door.
The room lamp output should stop immediately afte
r
turning on the ignition key during decaying operation.
The front room lamp comes on for 30 seconds (T3)
when receiving the unlock signal from the remote
control key while the door is closed. 1.
2.
3.
4.
The front room lamp output period is extended by 30 seconds (T3) when receiving the unlock signal
from the remote control key again during output.
When a door is opened during its extended period, the lamp stays on. If closed, operates as in step
2.
The room lamp output stops immediately after receiving the lock signal from driver’s door and
passenger’s door lock switch while the driver’s door and passenger’s door are closed. 5.
6.
7.
Door coupled front
room lamp switch

02-258710-01
The rear room lamp comes on when opening the
rear door while the door coupled rear room lamp
switch is pressed (except for luggage room lamp).
The rear room lamp extends its lighting period by 5
seconds when closing the rear door.
The room lamp output stops immediately after
turning the ignition key to “ON” position during
the extended period.
The room lamp output stops immediately after
receiving the lock signal from the rear door lock
switch or the remote control key while the rear door
is closed. 1.
2.
3.
4.
Door coupled front
room lamp switch
▶Rear Room Lamp

02-26
8) Ignition Key Hole Illumination
The ignition key hole illumination comes on when opening the driver’s door or passenger’s
door while the ignition key is removed.
The ignition key hole illumination stays on for 10 seconds when closing the door after step 1.
The output stops when the ignition key is turned to “ON” position.
The output stops when receiving the lock signal from the remote control key (under armed mode). 1.
2.
3.
4.

02-30
11) Door LOCK/UNLOCK Control
The door lock system outputs “LOCK” for 0.5 seconds (T1) when positioning the driver’s or
passenger’s door lock switch to lock position (while the driver’s and passenger’s door lock
switch is in “UNLOCK” position).
The door lock system outputs “UNLOCK” for 0.5 seconds (T2) when positioning the driver’s
or passenger’s door lock switch to unlock position.
LOCK” or “UNLOCK” by the door lock switch is ignored when outputting the “LOCK” or
“UNLOCK” by other functions.
The door lock/unlock system is not working regardless of the door lock switch positions when
connecting the battery.
All door lock signals are “UNLOCK” for 0.5 seconds (T4) just for once when receiving the
“LOCK” signal within 0.5 seconds (T3) after closing the driver’s or passenger’s door.
However, this operation is regardless of the ignition key positions. 1.
2.
3.
4.
5. ▶Door Lock/Unlock by Door Lock Switch
This function prevents the door from locking by shock when slamming a door while the ignition
key is inserted into the key switch hole. -