2013 SSANGYONG NEW ACTYON SPORTS engine

03-97010-06
Immobilizer and Warning Lamp ▶
This indicator comes on when the ignition key is
communicating with the engine control unit
(during engine starting) and goes out after
starting the engine.
When turning the ignition key to the "ON"
position, the ECU (engine control unit) transmits
the challenge message to the immobilizer unit.
(This is to verify whether the key is valid. If the
verification fails, it transmits re-verification signals
3 times for 2 seconds. If three re-verifications fail,
it stops verification and starts re-verification after
10 seconds.) (1)
ECUOnly when the two signals are identical, it recognizes the
key as the authorized one and transmits the positive
message to the ECU. (6)
The ECU enable the engine to be started. (7)
Do not drop or shock to the transponder in the key as it may be damaged.
With a damaged transponder, the engine cannot be started.
When you erase the code or register an extra key, please attend on the site.
In any cases, the immobilizer system can not be removed from the vehicle. If you attempt to
remove it and damage the system, starting will be impossible, so never attempt to remove,
damage or modify it.
The remote engine starter cannot be installed to the vehicle equipped with the immobilizer system. ·
·
·
·
·ON: In communication
Blinks twice at one second intervals: Immobilizer
system fault
Blinks once at 2 second intervals: Immobilizer unit
not coded
The immobilizer indicator does not come on if
the communication time between immobilizer
key and ECU is too short.
Instrument
panel

03-117010-06
5. REKES OPERATION LOGIC
1) Remote Door Lock
When briefly pressing the door lock switch on the remote control key for less than 0.5 seconds, all
doors are locked.
The system outputs the "LOCK" signal immediately after receiving the door lock message from the
remote control key. If the vehicle is locked while all doors including engine hood are closed, the theft
deterrent mode is activated (hazard warning lamps are blinking twice). 1.
2.

04-38210-01
1. SPECIFICATIONS
Item Specification
Rated voltage DC 13.5 V
Operating voltage DC 9 V ~ 16 V
Checking voltage DC 13.5 V
Operating temperature-30℃ ~ +80℃
Storage temperature-40℃ ~ +85℃
Illumination color Dial White
Pointer Red
LCD Red
Displays on Instrument
ClusterWarning and indicator
lamp1 blue indicator
13 red indicators
7 green indicators
8 yellow indicators
Gauge Vehicle speed
Fuel level
Engine coolant temperature
Engine speed (rpm)
LCD display Driving distance
Trip meter
Gear position display
Gear position display in
A/T(Left hand of LCD
display)A/T vehicle P, R, N, D, 1, 2, 3, 4, 5, 6
M/T vehicle R

04-58210-01
1. DESCRIPTIONS OF INDICATOR DISPLAY
Tachometer
SSPS warning light
Immobilizer indicator
Glow indicator
ESP indicator/warning light
Front fog light indicator
High beam indicator
ESP OFF indicator
Seat belt reminder (driver’s seat)
Seat belt reminder (passenger’s seat)
Engine oil pressure warning light
LCD Display
Engine overheat warning light
Engine check warning light
Auto cruise indicator
Light indicator
Winter mode indicator 1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.Engine hood open warning light
Battery charge warning light
Hazard Indicator
Water separator warning light
Air bag warning light
4WD CHECK warning light
4WD LOW indicator
4WD HIGH indicator
Speedometer
Turn signal indicator
Coolant temperature gauge
Brake warning light
Door ajar warning light
ABS warning light
Fuel gauge
Low fuel level warning light 18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33. It sends and receives information to/from each unit through CAN communication line. The LCD display
and separate ESP ON/OFF indicator are newly added.

04-98210-01
Power Turning ON condition
IGN IGN ON/ CAN signal input
IGN IGN ON/ CAN signal input
IGNIGN ON/ CAN signal input
(ESP & buzzer activated)
IGN IGN ON/ CAN signal input
IGN IGN ON, CAN signal input (EBD)
IGN IGN ON/ CAN signal input
IGN Signal input
BATT When door opened
IGN Charge system fault
IGN Switch input
IGN Switch inputNo. Symbol Item
13Engine check warning
lamp
144WD LOW
indicator
15ESP indicator/ warning
light
16 ESP OFF indicator
17 Brake warning light
184WD CHECK
indicator
19Air bag warning lamp
20Door ajar waning light
21Charge warning lamp
22Seat belt warning light
(driver)
23Seat belt warning light
(passenger)

04-10
No. Symbol Item
24Engine oil pressure
warning lamp
25Water separator
warning light
26Engine coolant
overheat warning light
27Engine hood open
warning lamp
28 EBD warning light
29 SSPS warning lamp
30Hazard warning lampPower Turning ON condition
IGN Signal input
IGN IGN ON/ CAN signal input
IGN IGN ON/ CAN signal input
IGN Switch ground
IGN CAN signal input
IGN Digital input
IGN Switch to High

04-118210-01
2. CONFIGURATION
1) RPM Gauge
The tachometer indicates engine speed in revolutions per minute. Multiply 1,000 to the current number,
then it will be the current number of engine revolutions.
Under the normal engine operating temperature, the proper idling speed is 700 ~ 800 rpm. The red zone
(danger rpm range) starts from 4,500 rpm.
Connect the tachometer for tune-up test and start the engine.
Eliminate the hysteresis by tapping the tachometer.
Compare the values on the tester and tachometer and replace the tachometer if the tolerance is
excessive. 1.
2.
3.
If the tachometer (engine rpm gauge) pointer vibrates or stops moving at a certain range, or abnormal
noises are heard from the tachometer, the tachometer may have a malfunction. If you have reason to
suspect that the reading from the tachometer differs from the actual engine speed (rpm), connect a
diagnostic device and compare the value on tachometer with the reading from the diagnostic device.
Check Method

04-16
Change
OrderMode LCD Display Description
1 TRIP A The maximum distance value that can be displayed is
999.9 km with increments of 0.1 km. The trip meter is
reset to 0.0 km when the value reaches above 999.9 km.
When measuring a trip distance, reset the distance value
in the mode you want to use by pressing the TRIP switch
for 1 sec. or more.
2 TRIP B The maximum distance value that can be displayed is
6,213.09 mi with increments of 0.62mi. The trip meter is
reset to 0.0 km when the value reaches above 999.9 km.
When measuring a trip distance, reset the distance value
in the mode you want to use by pressing the TRIP switch
for 1 sec. or more.
3 Distance to
emptyThe estimated distance that can be traveled is calculated
based on the current fuel level.
If the DTE is less than 50 km, "---" flashes on the display.
4 Driving time The driving time from resetting the value (0:00) until now
is displayed. The value displayed is accumulated while
the engine is running even if the vehicle is not driven. The
display range is 00:00 to 99:59. When measuring the
driving time, press the TRIP switch for 1 sec. or more to
reset the value.
5 Average
fuel
economyThe average fuel economy from resetting the value (--.-)
until now is displayed. The value displayed is
accumulated while the engine is running even if the
vehicle is not driven. The display range is 0.0 to 99.9
km/h. When measuring the average fuel economy, press
the TRIP switch for 1 sec. or more to reset the value. "--.-"
is displayed on the screen when resetting. The value is
reset automatically whenever the vehicle is fuelled.
5) Description for LCD Display
LCD display
Mode Description ▶