2013 SSANGYONG NEW ACTYON SPORTS oil

01-12
T/C oil supply pipeM161 25±2.5Nm
(Fitting Screw) -
M10 1 17±2.0Nm
(Hollow Bolt) -
T/C oil return pipe M6×16(to block) 2 10±1Nm -
M6×16
(to turbocharger) 2
10±1Nm -
EGR valve M8×303 25±2.5Nm -
Name SizeNumbers of
fastener Tightening
torque (Nm) Note (total
tightening torque)
Hot water inlet pipe M6×12210±1Nm -
Alternator M10×901(LO) 25±2.5Nm -
M10×116 1(HI) 46±4.6Nm -
Air conditioner compressor M8×85
425Nm -
Air conditioner bracket M6×25410±1Nm -
Intake manifold M8×35225±2.5Nm -
M8×110 625±2.5Nm -
Oil filter module M8×40625±2.5Nm -
M8×80 125±2.5Nm -
M8×140 225±2.5Nm -
Knock sensor M8×28220±5Nm -
Camshaft position sensor M8×14
110~14Nm -
T-MAP pressure sensor M6×20
110±1Nm -
Exhaust manifold M81040±4Nm -
Turbocharger M8325±2.5Nm -
T/C support bolt M8 x 35125±2.5Nm
(Turbo Side) -
M8 x 16 125±2.5Nm
(Block Side) -

01-130000-00
NameSizeNumbers of
fastener Tightening
torque (Nm) Note (total
tightening torque)
Idler pulley/tensioner pulley 1
45±4.5Nm -
Glow plug M5 4 20±2Nm -
Vacuum pump M6×25 3 10±1Nm -
Timing gear case cover M6×40 7 10±1Nm -
M6×45 1 10±1Nm -
M6×50 3 10±1Nm -
Cylinder head cover M6×35 21 10±1Nm -
Oil dipstick gauge cover M6×16 1 10±1Nm -
Oil filter cap 1 25±2.5Nm -
Fuel rail M8×25 2 25±2.5Nm -
Injector clamp bolt M6×44 2 9±1.0Nm
130˚±10˚ -
High pressure pipe
(between high pressure pump and fuel rail assembly) M17 1
30±3Nm -
High pressure pipe
(between fuel rail assembly and injector) M17 4
30±3Nm -
Crankshaft position sensor M5×14
1 8±0.4Nm -
Main wiring M6×16 5 10±1Nm -
Intake duct M8×25 425±2.5Nm -
Power steering pump M8×100 3 25±2.5Nm -
Cylinder head front cover M6×10
5 10±1Nm -
Ladder frame M8×355 30±3Nm
-
EGR pipe bolt
(to air duct) M6×16
2 10±1Nm -
EGR pipe bolt
(to EGR cooler) M8×25
225±2.5Nm -

02-4
2. TIGHTENING TORQUE
ComponentSizeBolt
Quantity Specified torque
(Nm) Remark
(Total torque)
Main bearing cap M12×8210 55±5Nm,
180˚ Not re-usable
Connecting rod cap M9×52840±5Nm,
90˚+10˚ 50 to 80 Nm
Rear cover M6×20610 ± 1 Nm -
Oil pump M8×35SOC 325 ± 2.5 Nm -
Drive plate M10×22845 ± 5 Nm,
90˚+10˚ Not re-usable
Crankshaft center bolt M20×851200 ± 20 Nm,
180˚+20˚ 660 to 720 Nm
Not re-usable
Oil pan M6×201810 ± 1 Nm -
M6×35 210 ± 1 Nm -
M6×85 210 ± 1 Nm -
M6×120 210 ± 1 Nm -
M8×40 225 ± 2.5 Nm -
HP pump main nut M14×1.5-8-1165 ± 5 Nm -
HP pump bolt M8×55325 ± 2.5 Nm -
Cylinder head M13×1501285Nm
270°±10° -
Camshaft cap M6×301610 ± 1 Nm -
M8×60 425 ± 2.5 Nm -
Exhaust stud bolt 1015±1.5Nm -
Exhaust sprocket bolt M8 x 16.5 1 25±2.5Nm-
Chain tensioner screw bolt M8 x 1.5
125±2.5Nm -
Coolant temperature sensor 1
20±2.0Nm -
Auto tensioner M8×30(LOW) 125±2.5Nm -
M10×75(Upper) 155±5.5Nm -
Coolant pump M6×50 110±1.0Nm -

02-50000-00
ComponentSizeBolt
Quantity Specified torque
(Nm) Remark
(Total torque)
Hot water inlet pipe M6×16 2 10±1Nm -
Alternator M10×90 1 25±2.5Nm -
M10×116 1 46±4.6Nm -
A/C bracket M8×25 4 7.8~11.8Nm -
A/C sub bracket M6×25 4 10±1Nm -
Intake manifold M8×35 2 25±2.5Nm -
M8×110 6 25±2.5Nm -
Oil filter module M8×40 6 25±2.5Nm -
M8×20 1 25±2.5Nm -
M8×140 2 25±2.5Nm -
Knock sensor M8×28 2 20±5Nm -
Cam position sensor M8×14 1 10~14Nm -
Booster pressure sensor M6×20 2 10±1Nm -
Exhaust manifold M810 40±4Nm -
Turbocharger M83 25±2.5Nm -
Support nut M81 25±2.5Nm -
T/C oil supply pipe M161 25±2.5Nm
(Fitting Screw) -
M10 1 17±2Nm
(Hollow Bolt) -
T/C oil return pipe M6×16(turbo side) 2 10±1Nm -
M6×16(block side) 2 10±1Nm -
EGR valve M8×30325±2.5Nm -
EGR pipe bolt (Intake side) M6×16
2 10±1Nm -
EGR pipe bolt
(EGR cooler side) M8×25
2 25±2.5Nm -
Support bolt M8×35125±2.5Nm
(Turbo Side) -
M8×16 125±2.5Nm
(Block Side) -

02-6
ComponentSizeBolt
Quantity Specified torque
(Nm) Remark
(Total torque)
Glow plug M5 4 20±2Nm -
Vacuum pump M6×253 10±1Nm -
Timing gear case cover M12×55 3 85±8.5Nm -
M6×25 7 10±1Nm -
M6×45 1 10±1Nm -
M6×50 3 10±1Nm -
Cylinder head cover M6×35 21 10±1Nm -
Oil gauge tube M6×16 1 10±1Nm -
Oil filter cap 1 25±2.5Nm -
Fuel rail M8×35SOC 2 25±2.5Nm -
Injector clamp bolt M6×60 2 10±1Nm,
120˚+10˚ -
High pressure pipe
(between HP pump and fuel rail) M17 1
30±3Nm -
High pressure pipe
(between fuel rail and injector) M17 4
30±3Nm -
Crank position sensor M5×14 1 5±1.0Nm -
Main wiring M6×16 5 10±1Nm -
Intake duct M8x25 4 25±2.5Nm -
Power steering pump M8×100 3 25±2.5Nm -
Cylinder head front cover M6×10 5 10±1Nm -
Ladder frame M8×16 5 30±3Nm -
Oil pump M8×35 3 25±2.5Nm -
EGR Cooler
MTG Bolt M8×16
225±2.5Nm -
M8×70 225±2.5Nm -
Idle pulley/Tensioner pulley 1
45±4.5Nm -

02-8
(2) Cylinder pressure leakage test
If the measured value of the compression pressure test is not within the specifications, perform the
cylinder pressure leakage test.Specified value ▶
Perform this test in the sequence of firing order.
Do not test the cylinder pressure leakage with wet type test procedure. (do not inject the engine oil
into the combustion chamber) -
-
Test condition: normal engine operating
temperature (80˚C)Specified value
Whole engine below 25%
at valve and cylinder head gasket below 10%
at piston ring below 20%
Crank the engine for approx. 10 seconds by
using the start motor. 2.
Record the test result and measure the
compression pressure of other cylinders with
same manner. 3.
If the measured value is out of specified
value, perform the cylinder pressure leakage
test. 4.

02-110000-00
4. GUIDELINES ON ENGINE SERVICE
To prevent personal injuries and vehicle damages that can be caused by mistakes during engine and
unit inspection/repair and to secure optimum engine performance and safety after service works, basic
cautions and service work guidelines that can be easily forgotten during engine service works are
described in.
Cautions before service works
For safe and correct works, you must observe the working procedures and instructions in this
manual. And, use the designated tools as follow:
Engine stand / Heavy duty engine jack
To prevent the engine from starting abruptly, do not allow anybody to get in the vehicle while
servicing in engine compartment.
Before work on engine and each electrical equipment, be sure to disconnect battery negative (-)
terminal.
Before service works, be sure to prepare the works by cleaning and aligning work areas.
Do not allow the foreign material get into the fuel injection system.
When removing the engine, use only the safety hook on engine and engine hanger. Do not support
the bottom of oil pan with a jack.
Engine and accessories ▶
-
-
-
-
-
-
▶
Completely drain the engine oil, coolant and fuel from engine before removal.
Before disassembling/assembling the engine components, carefully read the working procedures in
this manual.
Make sure to keep the specified tightening torques during installation.
Clean and properly lubricate the parts before reassembly.
Carefully check that there are not any interference while servicing. -
-
-
-
-

02-12
Electrical equipment ▶
Electric devices should be handled more carefully.
Currently, the engine has a lot of electric devices. there could be poor engine performance, incomplete
combustion and other abnormal symptoms due to short circuit or poor contact.
Before work on engine and each electrical equipment, be sure to disconnect battery negative (-)
terminal.
When replacing the electric device, use only genuine part and check the conditions of connections
and grounds. Loosened connection or ground make cause a fire and personal injury. -
-Fuel and lubrication system ▶
Do not allow the fluid and engine oil to make contact with the body paintwork and hoses.
If work on the fluid system such as fuel and oil, working area should be well ventilated and smoking
should be prohibited.
Gasket or seal on the fuel/lubrication system should be replaced with new ones and bolts and nuts
should be tightened as specified.
After removal/installation works, be sure to check whether there is leak on the connecting section. -
-
-
-
If fine dust or foreign material enters into DI engine's fuel system, there can be serious damages in HP
pump and injectors. Thus, be sure to plug the inlets of removed fuel line components with cap and
protect removed parts not to be contaminated with dirt. (Refer to cleanness in this manual while working
on DI engine fuel system)