2013 SSANGYONG KORANDO ESP

8) Buzzer
Specifications
Function Signal
Part name PKM17EPP-2002-B0 (MURATA, Piezoelectric Sound Components)
Permitted input voltage 25 VP-P or less
Operating temperature
Storage temperature
Sound pressure level 70 dB/min (3 Vp-p, 2 kHz, square wave, 10 cm)
Capacitance
Priority of instrument cluster buzzer output
If there are multiple signals at a time, the operation should be completed by the priority.
Priority
ItemBuzzer output
time
Operating condition
ON OFF
1 PAS See PAS
2 ESP 0.1sec 0.1secInstrument cluster buzzer output signal is
received from ABS/ESP
3Engine overheat
warning lamp0.5sec 0.5sec
4Water separator
warning light0.5sec 0.5secWater separator warning light ON with
IGN ON
5 Parking brake 2.8sec 1.5secParking brake applied depending on
vehicle speed

Pin No.Message
Operating condition
Domestic Export
Cruise control This message comes on when the ECO cruise mode
is deactivated.
EMSThis message comes on when the engine is faulty.
LampThis message comes on when the tail lamps are ON
with the ignition in the "OFF" or "ACC" position.
SUNROOF
SYSTEMFor the vehicle with SKM, this message comes on
when the sunroof is open with the ignition in the "OFF"
or "ACC" position. For the vehicle without SKM, this
comes on when the sunroof is open with the ignition in
the "OFF" position and the key removed.
Low fuel level This message comes on when the remaining fuel is
insufficient.
ESP checkThis message comes on when the ESP system is
faulty.
ABS check This message comes on when the ABS system is
faulty.
Engine oil level
checkLCD display shows this message when the engine oil
level is low. Have the system checked at Ssangyong
Authorized Service Center.Pin No. Message Operating condition
Auto cruiseLCD display shows this message when turning on the
cruise control switch with ignition ON or engine
running. This message disappears when activating the
cruise control lever.

Lower main switch
Item Specification
Lower main switch4WD LOCK switch DC 12V - 0.1A
ESP OFF switch DC 12V - 0.1A
Steering wheel heating switch DC 12V - 0.1A
Center fascia switch
Item Specification
Center fascia switchHazard warning flasher switch DC 12V - 0.1A (max. 30 mA)
TRIP/RESET switch DC 12V - 0.1A (max. 30 mA)
Windshield heating switch DC 12V - 0.1A (max. 30 mA)
Rear glass and outside rearview mirror
heating switchDC 12V - 0.1A (max. 30 mA)
Power window main switch
Item Specification
Power window main
switchRated voltage
DC 12 V
Operating voltage DC 9 to 16 V
Rated loadAUTO switch 0.7 A (motor load)
AUTO/MANUAL switch 10 A (motor load)
Window lock switch 10 A (motor load)
Door unlock switch 0.4 A (motor load)
Power window sub switch
Item Specification
Power window sub
switchRated voltage DC 12 V
Operating voltage DC 9 to 16 V
Rated load Manual switch 10 A (motor load)

8510-00
Door lock/unlock switch
Function of door lock/unlock switch
There are 5 actuators in door lock/unlock system (including tailgate). All of them can control the
corresponding door lock and unlock separately. But, the driver door lock switch can control all door
locks. The BCM controls the lock/unlock switch using the door lock/unlock relay. This is a same control
type with Auto door lock function that locks the doors when the vehicle speed exceeds 30 km/h. (see
circuit diagram)
Door lock/unlock relay (integrated in BCM)
Door lock/unlock switch
When the door lock/unlock switch is pressed while all doors including the tailgate are locked, all doors
will be unlocked. When the switch is pressed again, all doors will be locked.

Outside rearview mirror switch
(1) Overview
Outside mirror folding/unfolding switch
The outside mirrors are folded/unfolded
whenever pressing this switch.
Mirror selection switch
LH: Driver side mirror
RH: Passenger side mirror A.
B.Mirror aiming switch
Adjust the selected mirror up, down, left,
or right by pressing the corresponding
edges of the switch to get a desired view. C. It is mounted to the door trim and can be adjusted to up, down, left or right so that the driver can obtain a
clear view of the rear of the vehicle depending on the driver's physical condition. The driver can fold the
outside rearview mirror when passing by the narrow road or parking the vehicle. Do not fold or unfold the
outside rearview mirrors manually since the outside rearview mirror folding switch is a push-lock type
switch. This may cause a malfunction of the relevant devices.
2) Outside Mirror Switch

Lower main panel switch
3) Lower Main Panel Switch
Rear fog lamp switch (EU ONLY)
Steering wheel heating switchHLLD (Headlamp Leveling Device)4WD LOCK switch
ESP OFF switch This helps the driver to drive the vehicle comfortably by operating the switch for the driving situation.

8510-00
4WD LOCK switch
This switch is of push lock type, which
enables to increase/decrease the
torque to the rear wheels in AWD
mode.
Steering wheel heating
switch
This switch is of push return type,
which is used to activate or deactivate
the steering wheel heating function.
ESP OFF switch
The ESP OFF switch is of push return
type, which is used to stop or resume
the ESP function.
4WD LOCK switch
This switch is of push lock type, which
enables to increase/decrease the
torque to the rear wheels in AWD
mode.
HLLD
(Headlamp Leveling Device)
The headlamp aiming can be adjusted
by using this dial-type switch.
Rear fog lamp switch
(EU ONLY)
This switch is of push return type,
which sends ON/OFF signal to the
BCM so that the BCM can switch on
the lamps by activating the rear fog
lamp relay.

8510-00
Overview
The ESP OFF switch is located to the driver's lower panel. When the driver press the ESP OFF switch, the
ESP OFF indicator lamp comes on in the instrument cluster and the ESP becomes disabled. However, the
ABS still works as it should.
ESP ON/OFF switch (only for vehicle with ESP)
ESP OFF switch
(2) ESP OFF switch
ESP OFF indicator lamp module (only for vehicle with ESP)
The ESP function turns ON and OFF each time the driver presses the ESP ON/OFF switch. This
switch is a constant-open type instant contact switch and grounded to IGN1. The default setting is
ESP ON and it is turned on and off each time the switch is pressed.
If the driving wheels are slipping on snowy or icy roads, the engine rpm may not increase even
when you depress the accelerator pedal, and accordingly, you may not be able to move your
vehicle. In this case, stop the ESP function by pressing the ESP OFF switch. When the ESP OFF
switch is pressed, the ESP function stops and the vehicle is driven independently from the sensor
outputs. -
-
The ESP OFF lamp shows how the ESP function works.
The ESP OFF lamp comes on when:
ESP function is deactivated by switch input -