2013 SSANGYONG KORANDO ESP

REKES key panic alarm (for vehicles without SKM)
The REKES key panic signal is received.
The hazard warning lamp and warning horn are activated for 30 seconds (T1) at intervals of 0.5 sec.
ON/0.5 sec. OFF. A.
B. Operation 1.
The hazard warning lamp and warning horn are activated by REKES panic function.
The REKES panic LOCK and panic signals are received.
The panic function is interrupted and other functions are activated by the corresponding command. C.
D.
E. Operation 2.
The theft deterrent alarm is activated.
The panic function is interrupted and theft deterrent alarm is set. F.
G. Operation 3. (during operation 1)
15. PANIC ALARM CONTROL
The panic alarm functions regardless of the ignition status. -

Smart key panic alarm (for vehicles with SKM)
The ignition is turned ON or OFF, or the ACC is turned ON.
The smart key panic signal is received.
The hazard warning lamp and siren are activated for 30 seconds (T1) at intervals of 0.5 sec. ON/0.5
sec. OFF. A.
B.
C. Operation 1.
The theft deterrent alarm is activated.
The panic function is interrupted and theft deterrent alarm is set. G.
H. Operation 3. (during operation 1)
The panic function is activated by the signals from SKM. - The hazard warning lamp and warning horn are activated by smart key panic function (operation 1).
The followings occur: D.
E. Operation 2.
The panic button of the smart key is pressed.
When other function signal is received, the command is executed while the panic function is kept. -
-
The panic function is interrupted and other functions are activated by the corresponding command. F.

LH/RH turn signal lamp control
The LH/RH turn signal lamp switch is turned ON with IGN ON.
The LH/RH turn signal lamp flashes 75 times per minute (T1), and the internal buzzer sounds at
intervals of 0.4 sec. ON/0.4 sec. OFF.
The LH/RH turn signal lamp and internal buzzer are deactivated when the LH/RH turn signal lamp
switch is turned OFF. A.
B.
C. Operation 1.
Abnormal current (less than 3 A or more than 7 A) detection signal is input while the lamp is ON.
The LH/RH turn signal lamp flashes 100 times per minute (T2), and the internal buzzer sounds at
intervals of 0.3 sec. ON/0.3 sec. OFF. D.
E. Operation 2.
The LH/RH turn signal lamp is activated only with IGN ON. F. Operation 3.
20. FLASHER FUNCTION
The LH/RH turn signal lamp flashes 3 times once the corresponding lamp switch is turned ON.
When the LH turn signal lamp switch is turned OFF during the 3 times flashing, the turn signal
lamp goes out after the flashing operation.
When the LH turn signal lamp switch is turned ON during the 3 times flashing, the turn signal lamp
flashes 3 more times.
When the RH turn signal lamp switch is turned ON during the 3 times flashing, the LH turn signal
lamp goes out immediately and the RH turn signal lamp flashes 3 times before switching off. -
-
-

AUTO hazard warning flasher control
The hazard warning lamp comes on 3 times (T3) when the AUTO hazard warning lamp switch is
pressed for less than 0.6 seconds (T1). A. Operation 1.
The hazard warning lamp comes on 10 times (T4) when the AUTO hazard warning lamp switch is
pressed for 0.6 seconds or more (T2).
The turn signal lamp switch is pressed during the AUTO hazard warning lamp operation.
The corresponding turn signal lamp is activated after this AUTO hazard warning lamp operation. B.
C.
D. Operation 2.
The AUTO hazard warning lamp can be controlled only with IGN ON.
The input from the AUTO hazard warning lamp switch is ignored during the turn signal lamp
operation by the turn signal lamp switch.
Priority of operation: (Hazard warning lamp switch > LH/RH turn signal lamp > AUTO hazard
warning lamp switch) -
-
-
Operating process

Emergency hazard warning lamp control (coupled with ABS)
The emergency stop signal is input from the ABS/ESP module with the vehicle driven at 50 km/h or
more.
The hazard warning lamp flashes at 4 Hz (T1) and internal buzzer (chime) sounds at 1.25 Hz. A.
B. Operation 1. (emergency stop signal)
During operation 1 (emergency stop signal activated)
The vehicle speed decreased to 50 km/h or less
The hazard warning lamp flashes for 10 seconds (T2) at 1.25 Hz and then goes out. C.
D.
E.
The BCM activates emergency hazard warning lamp operation when receiving emergency braking
signal from the ESP/ABS.
Priority of operation
(Manual operation of hazard warning lamp > Emergency stop signal > Emergency AUTO hazard
warning lamp > AUTO hazard warning lamp) -
lamp)
During operation 2 (emergency AUTO hazard warning lamp)
The hazard warning lamp switch is turned OFF.
The hazard warning lamp is turned OFF because the manual operation overrides the emergency
AUTO operation. F.
G.
H.
The emergency stop signal and emergency AUTO hazard warning lamp signal are switched off
when the vehicle speed exceeds 10 km/h (if emergency stop signal is input).

Operating process
The BCM activates emergency hazard warning lamp operation when receiving emergency braking
flasher ON signal from the ESP/ABS.
When the emergency stop signal is input through the P-CAN, the hazard warning lamp flashes with the
frequency of 4 Hz and the internal buzzer sounds at 1.25 Hz.
P-CAN signal during operation: Emergency Stop=EBL_INFO=0*0=Hazard Warning Lamp unrequested

8712-03
Passive entry function actuation area: Within 1.2 m from the door handle antenna
Passive tailgate open actuation area: Within 1.2 m from the center of the bumper -
-
(1) Passive entry actuation area
Searching for a smart key signal from the outside the vehicle is prioritized in the theft deterrent mode
when the passive entry signal is input. Searching for a smart key signal from the inside is prioritized
when the theft deterrent mode is deactivated.
The system searches a smart key only in the actuation area of a switch, which the signal is input
(driver/passenger door handle switches and tailgate open switch). -
-
4. PASSIVE ENTRY MANAGEMENT
1) Passive Function
The passive entry actuation area refers to the area where passive LOCK/UNLOCK can be
performed by pressing the switch on the driver or passenger door handle with a smart key carried by
the driver.
The passive tailgate open actuation area refers to the area where the tailgate can be opened by
pressing the tailgate switch with a smart key carried by the driver. -
-
LF transmission: Verification request signal
RF transmission: Response signal

8712-03
(5) Passive tailgate open
The tailgate open control is activated by the tailgate open switch with a valid smart key present within the
passive entry actuation area.
Passive tailgate open by tailgate open switch
When the tailgate is closed with all doors closed, the system enters the theft deterrent mode after
checking a valid smart key inside the vehicle. When a valid smart key is found inside the vehicle, the
external buzzer and smart key detected warning indicator is operated for 10 seconds.
If no smart key is identified as being outside the vehicle, the passive gate open process is stopped
and restarted when the next signal is received from the tailgate open switch.
Smart key searching
* Theft deterrent mode: deactivated after searching the outside vehicle
* Theft deterrent mode deactivated: outside searching after inside searching -
-
-The driver door is locked and the system in the theft deterrent mode.
The tailgate open switch signal is received.
The BCM sends the valid smart key verification request signal to the SKM.
The SKM verifies if a smart key is outside the vehicle using the corresponding rear bumper antenna
(LF verification) (The SKM searches the last smart key used first. If a valid smart key searching is
completed, searching for a key in the luggage compartment and inside the vehicle is started).
The verification signal (RF verification) from the smart key is sent to the REKES antenna of the SKM.
The SKM sends the Passive tailgate open signal to the BCM through the B-CAN if the verified smart
key is found outside the vehicle.
The BCM activates the tailgate open relay according to the signal received from the SKM.
(Only the theft deterrent mode for tailgate is deactivated.) -
1.
2.
3.
4.
5.
6.