2013 SSANGYONG KORANDO belt

2. INPUT SIGNALS
NO Input signal Logic
1 IGN1 ON = Battery voltage (IGN ON or START)
2 IGN2 ON = Battery voltage (IGN ON)
3 Alternator ON = Battery voltage (engine running)
4 Key reminder switch IN = Battery voltage (key inserted)
5 Driver door LOCK detecting switch LOCK = GND, UNLOCK = OPEN
6 Driver door UNLOCK detecting switch LOCK = OPEN, UNLOCK = GND
7 Passenger door LOCK detecting switch LOCK = GND, UNLOCK = OPEN
8 Passenger door UNLOCK detecting
switchLOCK = OPEN, UNLOCK = GND
9 Rear door LOCK detecting switch LOCK = OPEN, UNLOCK = GND
10 Puddle lamp ON = (-) OUTPUT
11 Driver door open switch OPEN = GND, CLOSE = OPEN
12 Passenger door open switch OPEN = GND, CLOSE = OPEN
13 Rear LH door open switch OPEN = GND, CLOSE = OPEN
14 Rear RH door open switch OPEN = GND, CLOSE = OPEN
15 Tailgate switch OPEN = GND, CLOSE = OPEN
16 Hood switch OPEN = GND, CLOSE = OPEN
17 Sunroof switch OPEN = GND, CLOSE = OPEN
18 headlamp switch ON = GND, OFF = OPEN
19 Folding/unfolding switch ON = GND, OFF = OPEN
20 Crash door LOCK/UNLOCK switch ON = GND, OFF = OPEN
21 Crash sensor (air bag) ON = 200 ms Low signal, OFF = OPEN
22 Front defogger (heated wire) switch ON = GND, OFF = OPEN
23 Rear defogger (heated wire) switch ON = GND, OFF = OPEN
24 Wiper switch 1 ON = GND, OFF = OPEN
25 Wiper switch 2 ON = GND, OFF = OPEN
26 Driver seat belt switch Unbuckled = GND, Fastened = OPEN
27 Passenger seat belt switch (only EU) Unbuckled = GND, Fastened = OPEN
28 Rain & AUTO light sensor LIN communication

3. MAJOR FUNCTIONS
Item Functionw/o SKM w/ SKM
1 WIPER CONTROL Wiper MIST and washer coupled wiper O O
AUTO washer coupled wiper operation O O
Rain sensor coupled wiper (LIN) O O
Speed sensitive intermittent wiper O O
Wiper LO/HI control O O
2 Ignition key warning
lampIgnition key reminder warning O X
Ignition key reminder O X
External buzzer control X O
Door LOCK prevention function when a door
is ajarOO
3 Tail lamp control Tail lamp switch ON warning O O
Tail lamp warning display X O
Tail lamp AUTO switching off O O
4 Door ajar warning Door ajar control X O
Door ajar warning O O
5 Seat belt control Seat belt warning O O
Seat belt reminder O O
6 Sunroof warning Sunroof warning O O
Sunroof warning display X O
7 Room lamp control Door coupled room lamp dim control O O
Room lamp AUTO switching off O O
Room lamp control display X O
8 Ignition key hole lamp Ignition key hole lamp control O X
9 Defogger (heated wire)
controlFront defogger (heated wire) control O O
Rear defogger (heated wire) control O O

Seat belt internal buzzer (chime) and warning lamp
The ignition is turned ON from OFF with the driver and passenger seat belts unbuckled.
The internal buzzer (chime) sounds and the warning lamp comes on for 6 seconds (T2).
(internal buzzer controlled by BCM, warning lamp controlled by instrument cluster) A.
B. Operation 1.
The ignition is turned ON from OFF with the driver and passenger seat belts unbuckled.
The internal buzzer (chime) does not sound but the warning lamp comes on for 6 seconds (T2).
(The seat belt reminder is operated when the vehicle is driven at 10 km/h (for EU), 25 km/h (for GEN)) C.
D. Operation 2.
When the fastened driver seat belt is unbuckled with IGN ON.
The internal buzzer (chime) sounds and the driver seat belt warning lamp comes on for T2 again. E.
F. Operation 3.
The ignition is turned OFF while the internal buzzer (chime) and seat belt warning lamp are activated.
The internal buzzer (chime) and seat belt warning lamp are deactivated. G.
H. Operation 4.
8. SEAT BELT CONTROL
The driver seat belt is fastened while the internal buzzer (chime) and seat belt warning lamp are
activated.
The internal buzzer (chime) does not sound but the warning lamp comes on for the time remaining. I.
J. Operation 5.
When the seat belt reminder operation conditions are met during the warning, the seat belt reminder
is operated after stopping the warning output.
For the passenger seat, however, the system detects if the passenger seat is empty or occupied
and operates the warning lamp only for the first time. After that, the only seat belt reminder detects if
the passenger seat is occupied. -
-

Seat belt reminder operation
A
BIf the seat belt is fastened after the seat belt reminder is activated, the output of the reminder is
turned OFF immediately. The reminder will be operated again whenever the seat belt is
unbuckled.
CWhen the seat belt reminder is activated initially with the seat belt unbuckled, the internal buzzer
(chime) is turned ON for 0.02 seconds and then turned OFF for 1.18 seconds (this cycle
continues for 5 minutes) and the driver seat belt warning lamp on the instrument cluster remains
on.
DWhen the seat belt reminder is activated with the seat belt unbuckled, the internal buzzer (chime)
is turned ON for 0.02 seconds and then turned OFF for 1.18 seconds (this cycle continues for 5
minutes) and the passenger seat belt warning lamp on the instrument cluster remains on, after
detecting that the passenger seat is occupied through the input value of the passenger seat
occupancy sensor.
EWhen the vehicle speed is changed while the seat belt reminder is turned on, the internal buzzer
(chime) is operated as follows:
FPriority of internal buzzer (chime) operation
(Seat belt reminder > ignition key reminder > sunroof warning > tail lamp warning > hazard
warning flasher on > turn signal indicator)GEN
The seat belt reminder is operated when the
vehicle is driven at 25 km/h or more with IGN
ON and alternator in High status (engine
running), and driver seat belt is not fastened. If
the vehicle speed is decreased to less than 25
km/h within 5 minutes after the seat belt
reminder is activated, the internal buzzer
(chime) is turned off. If the vehicle speed is
increased to 25 km/h or more, the buzzer
signal is output for 5 minutes. Only EU If the driver and passenger seat belts are not
fastened with the ignition switch ON, engine
running, vehicle speed above 10 km/h and
any passenger occupied, the seat belt
reminder is activated. In addition, even though
the vehicle speed reduces to below 10 km/h
after the reminder is activated at speed of 10
km/h or higher, it will remain activated.
Vehicle speedFunction
Remarks
Interior buzzerInstrument
cluster
25 Km/h to 49 Km/h
(10km/h~49km/h)0.02 sec. ON / 1.18 sec. OFF Remains on (Only EU)
50 Km/h to 99 Km/h 0.02 sec. ON / 0.98 sec. OFF Remains on
100 km/h or more 0.02 sec. ON / 0.78 sec. OFF Remains on

Hazard warning lamp switch control
The hazard warning lamp switch is turned ON with IGN ON or OFF.
The hazard warning lamp flashes 75 times per minute (T1), and the internal buzzer sounds at
intervals of 0.4 sec. ON/0.4 sec. OFF.
The hazard warning lamp and internal buzzer are deactivated when the hazard warning lamp switch
is turned OFF. A.
B.
C. Operation 1.
Operation 1. Abnormal current (less than 3 A or more than 7 A) detection signal is input while the
lamp is ON.
The hazard warning lamp flashes 100 times per minute (T2), and the internal buzzer sounds at
intervals of 0.3 sec. ON/0.3 sec. OFF. D.
E. Operation 2.
Hazard warning lamp functions at B+ or more.
The allowed time difference between the LH and RH turn signal lamp operations is within 0.1
seconds.
The hazard warning lamp overrides the turn signal lamp.
Priority of internal buzzer (chime) operation while the hazard warning lamp is ON
(Seat belt reminder > Ignition key reminder > Sunroof open > Tail lamp ON > Hazard warning lamp
> Turn signal lamp) -
-
-
-

Low fuel level warning lamp
Warning lamp
(amber)
Engine overheat warning lamp
Warning lamp
(red)
Door ajar
Warning lamp
(red)
Seat belt reminder
Warning lamp
(red)
Air bag
Warning lamp
(red)
However, the fuel level may change slight depending on vehicle
condition, inclination of the road, etc. Also, it blinks if there is a short or
open circuit between the fuel level sensor and cluster.
interval of 1 second, a message is displayed, the warning sounds once
through the speaker and the buzzer sounds at an interval of 0.5 seconds.
This lamp comes on when any door is open or not closed completely.
(both STD and SVC class)
This lamp comes on when the ignition switch is pressed ON.
It keeps coming on if the driver's seat belt is not fastened.
This lamp comes on when the ignition switch is pressed to the ON mode.
Then, it goes off if the system is normal.
If this lamp stays on while driving, it means that the air bag system is faulty.

Indicator
(green)
Passenger seat belt reminder
Left turn signal indicator
Right turn signal indicator
Indicator
(red)
Indicator
(green)
Indicator
(green)
Winter mode indicator(DSL only)
The right turn signal indicator blinks if the light switch is pushed up to
the right, and both turn signal indicators blink if the hazard warning flasher
switch is pressed.
When the mode switch is pressed, the winter mode is selected and the
winter mode indicator comes on on the instrument cluster. The winter
mode is used to start off on a slippery road with the 2nd gear. If the switch
is pressed again, the winter mode is deactivated and system returns to
standard mode.This indicator comes on when the ignition switch is turned to the "ON"
position and goes off when the passenger's seat belt is fastened.
The left turn signal indicator blinks if the light switch is pushed down to the
left, and both turn signal indicators blink if the hazard warning flasher switch
is pressed.
Smart key warning lamp
Indicator
(amber)
This lamp comes on when the uncertified transponder or smart key is
detected,
SKM system is defective or there is no smart key in the vehicle.

8010-01
Operations for power supply in SVC
When the ignition switch is turned to ON position, the message "WELCOME" is displayed for 2
seconds on the DOT LCD and the seat belt reminder comes on for 4 seconds. However, if a signal
with higher priority is received, the seat belt reminder comes on only for 2 seconds
to display it.
The pre-warning (system check) indicator comes on for 4 seconds and goes off 0.4 seconds after
that the ignition is switched on.
All input signals can be input 4 seconds after the pre-warning (system check) indicator starts
illuminating.
Only the symbol and DOT LCD are illuminated initially, if the SKM (Smart Key Module) or door (B-
CAN) signal is received
while B+ power is supplied.
If the ignition is switched on with the LCD illuminated, the DOT LCD and the symbol follow
the side fascia panel.
When the step 1, 2 and 3 are performed after 4 seconds, the seat belt warning lamp is deactivated
in advance.
Dial light ON condition: Lights up gradually for 2 seconds when the ignition is switched on. 1.
2.
3.
4.
5.
6.
4) Illumination & Brightness
(1) Operations for Power Supply