2013 RENAULT KANGOO fuel

17B-119
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$083.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 18
DF639
CONTINUED 2
2.DEFNOTESNone.
Check the ignition coil circuits (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 (Logan and Sandero), MR 451 (Duster) or MR 423 (Thalia 2/Symbol
2), Mechanical, 13A, Fuel supply, Fuel circuit: Operating diagram),
Check the fuel supply pump circuit (see MR 388 (Logan and Sandero), MR 451 (Duster) or MR 423 (Thalia 2/
Symbol 2), Mechanical, 13A, Fuel supply, Fuel circuit: Operating diagram),
Check the condition of the cylinder injectors (see MR 388 (Logan and Sandero), Mechanical, 13A, Fuel supply,
Injector rail - Injectors: Removal - Refitting, MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), Mechanical,
17B, Petrol injection, Injector rail - Injectors: Removal - Refitting),
Check the cylinder compressions.

17B-123
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$083.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF884
PRESENT OR
STOREDADDITIONAL FUEL CIRCUIT PUMP RELAYCC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESConditions for application to a stored fault:
The fault is declared present after running command
AC224 Additional fuel circuit pump relay.
See the Wiring Diagrams Technical Note for Logan, Sandero, Kangoo VLL.
Check the supply of the control circuit of the additional fuel supply pump relay with a test light by running command
AC224.
Check the cleanliness and condition of the connector of the additional petrol pump relay, component code 1639
and of the injection computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
–3ACK between components 1639 and 120,
–3FB between components 1639 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
Check the supply of the power circuit of the additional fuel supply pump relay with a test light by running command
AC224. If the check is correct, replace the pump, component code 1639 (see MR 388 (Logan and Sandero) or
MR 374 (Kangoo VLL), Mechanical, 19C, Tank, Fuel pump of the additional fuel tank: Removal - Refitting).
If the fault is still present, contact the Techline.
V42_V04_DF884/V42_V05_DF884/V42_V06_DF884/V42_V14_DF884/V42_V16_DF884/V42_V18_DF884

17B-126
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF894
PRESENT OR
STOREDADDITIONAL FUEL CIRCUIT SOLENOID VALVECC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
For engines: K4M, K7M, D4D
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Kangoo VLL.
Check the connection and condition of the connector of the additional fuel circuit solenoid valve, component code
1640 and the injection computer connector, component code 120.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity, insulation, and absence of interference resistance on the following connections:
–3ACM between components 1640 and 120,
–3FB between components 1640 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
Check the supply of the solenoid valve using a test light, by running command AC217 Additional fuel circuit
solenoid valve.
Check the internal resistance of the solenoid valve, component code 1640 on the computer connector; its value
must be between: 12  < X  16  (Duster F4R engine) or 22  < X  30  (Duster K4M engine). If the resistance
is incorrect, replace the solenoid valve.
If the fault is still present, contact the Techline.
V42_V04_DF894/V42_V05_DF894/V42_V06_DF894/V42_V14_DF894/V42_V16_DF894/V42_V18_DF894
PETROL INJECTION
Fault finding – Interpretation of faults

17B-127
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF894
CONTINUED 1
For engines: F4R 404, 405, 408
NOTESThis fault corresponds to an electrical fault of the additional fuel circuit injector, which is
fitted directly on the throttle valve. It is not a solenoid valve fault.
See the Wiring Diagrams Technical Note for Duster.
Check the fitting and sealing of the additional fuel circuit injector
If there is leakage, replace the defective component (the injector inlet hose, the injector seal, the additional fuel
circuit injector).
Check the connection and condition of the connector of the additional fuel circuit injector, component code 1640
and the injection computer connector, component code 120.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity, insulation and the absence of interference resistance on the following connections:
–3ACM between components 1640 and 120,
–3FB between components 1640 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.

17B-128
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF894
CONTINUED 2
Check the supply of the additional fuel circuit injector using a multimeter in the voltmeter position (direct current
mode).
Run command AC217 Additional fuel circuit solenoid valve and check that the average voltage reading is
different from 0 V.
Check the internal resistance of the additional fuel circuit injector, component code 1640 on the computer
connector. Its value must be between: 13.775   X  15.225 or 24   X  30  (F4R engine on Duster) at
20ºC. If the resistance is incorrect, replace the injector.
If the fault is still present, contact the Techline.

17B-139
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF1034
PRESENT OR
STOREDCOMBUSTION MISFIRES
1.DEF: Polluting misfiring
2.DEF: Destructive misfiring
NOTESFault priorities:
Deal with the following faults first:
–DF109 Low fuel level misfiring
–DF059 Misfiring on cylinder 1
–DF060 Misfiring on cylinder 2
–DF061 Misfiring on cylinder 3
–DF062 Misfiring on cylinder 4
Special notes:
After this fault appears:
the OBD warning light is on.
Conditions for application to a stored fault:
The fault is declared present:
Engine idling.
1.DEF
NOTESNone.
Check the ignition coil circuit of cylinder 3,
Check the fuel supply circuit (see MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374
(Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel circuit: Operating diagram),
Check the fuel supply pump circuit,
Check the condition of the cylinder 3 injector (see MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio
II F 6) or MR 374 (Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal -
Refitting),
Check the compression of cylinder 3.
V42_V04_DF1034/V42_V05_DF1034/V42_V06_DF1034/V42_V14_DF1034/V42_V16_DF1034/V42_V18_DF1034

17B-140
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF1034
CONTINUED
After repair, check that the catalytic converter was not damaged by the misfire.
To do this, switch on the ignition, run the catalytic converter test SC006 Run OBD test: Catalytic converter and
start the engine (only depress the brake pedal to authorise the starting of the engine,
Do not depress the accelerator pedal or the clutch pedal).
At the end, check the test results:
STATUS1: Fault finding was not performed/impossible to obtain the necessary conditions
STATUS2: The component is in an average condition - sensor OK
STATUS3: The component is in a good condition - sensor OK
STATUS4: The component is in poor condition - replace the catalytic converter (see MR 451 (Duster), MR 423
(Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 19B, Exhaust, Catalytic
converter: Removal - Refitting).
Note: The catalytic converter procedure is not carried out if a fault is present.
Important: Do not run the procedure if a new catalytic converter is fitted.
2.DEF
NOTESNone.
Check the ignition coil circuit of cylinder 3,
Check the fuel supply circuit (see MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374
(Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel circuit: Operating diagram),
Check the fuel supply pump circuit,
Check the condition of the cylinder 3 injector (see MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio
II F 6) or MR 374 (Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal -
Refitting),
Check the compression of cylinder 3.

17B-141
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF1058
PRESENT OR
STOREDINLET PRESSURE CONSISTENCY1.DEF: Abnormal voltage
2.DEF: Abnormal pressure
NOTESPriority when dealing with a number of faults:
DF079 Motorised throttle valve servo
Conditions for applying the fault finding procedure to a stored fault:
The fault is considered present under the following conditions:
–For 2.DEF engine running at idle speed.
Special note:
For 2.DEF, the OBD warning light and level 1 fault warning light illuminate,
For 1.DEF, the OBD warning light illuminates.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the fitting and sealing of the inlet air pressure sensor, component code 147 (condition of the seals) and look
for possible leaks on the inlet air pipe.
Check the connector of the inlet air pressure sensor, component code 147.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the supply voltage of the sensor on connections 3AJR and 3AJP.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3AJP between components 120 and 147,
–3AJR between components 120 and 147,
–3AJQ between components 120 and 147.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Replace the inlet air pressure sensor, component code 147 and check that the fault is no longer present (see MR
388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374
(Kangoo VLL), Mechanical, 12A, Fuel mixture, Air inlet: Description).
If the fault is still present, contact the Techline.
V42_V04_DF1058/V42_V05_DF1058/V42_V06_DF1058/V42_V14_DF1058/V42_V16_DF1058/V42_V18_DF1058