2013 RENAULT KANGOO fuel

17B-161V2 MR-376-X76-17B050$100.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
Tool status Diagnostic tool title
ET001Computer + After ignition
ET038Engine
ET039Brake pedal
ET041Gearbox ratio
ET047Fuel pump control circuit
ET051Throttle stop programming
ET089Flywheel target programming
ET148OBD warning light activation request
ET321Air conditioning compressor
ET405Clutch pedal switch
ET434Low fuel level
ET571LPG minimum signal
ET673Jammed accelerator pedal detected
ET717Target gearbox ratio
ET734Heating resistor 1 relay control
ET735Heating resistor 2 relay control
ET736Heating resistor 3 relay control
ET759Braking multiplex signal detected
ET760First starting
ET775Camshaft TDC* synchronisation
ET798Clutch wire contact connection
ET799Brake wire contact
PETROL INJECTION
Fault finding – Status summary table

17B-166V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET047FUEL PUMP CONTROL CIRCUIT
STATUS DEFINITIONACTIVE: This status indicates that the fuel pump is active.
INACTIVE: This status indicates that the fuel pump is inactive.
Conformity check: Engine stopped, ignition on or engine running.
ACTIVEStatus ET047 is ACTIVE when starting the engine. In the event of a fault apply the
interpretation of DF085 Fuel pump relay circuit.
INACTIVEStatus ET047 is INACTIVE when the engine is stopped and the ignition off.
V42_V04_ET047/V42_V05_ET047/V42_V06_ET047/V42_V14_ET047/V42_V16_ET047/V42_V18_ET047

17B-198
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
PR139RICHNESS ADAPTIVE OPERATION
PA R A M E T E R
DEFINITIONNo faults must be present.
Conformity check with the engine running and engine coolant temperature > 80°C
Check the sealing of the fuel vapour absorber bleed.
Repair if necessary.
With the engine warm in the idle speed regulation phase, look at parameter PR139.
– If the parameter goes to MAXIMUM stop, there is not enough fuel or too much air in the mixture.
– If the parameter goes to MINIMUM stop, there is too much fuel or not enough air in the mixture.
Check the cleanliness and correct operation of:
– petrol filter,
– petrol pump,
– fuel circuit,
–tank,
– air supply pipe,
– air filter,
– plugs.
Repair if necessary.
Check:
– the compressions,
– the valve clearance,
– the ignition.
Repair if necessary.
V42_V04_PR139/V42_V05_PR139/V42_V06_PR139/V42_V14_PR139/V42_V16_PR139/V42_V18_PR139

17B-213V2 MR-376-X76-17B050$140.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
*TDC: Top Dead Centre
**GMV: fan assemblyTool
commandDiagnostic tool title Comments
RZ001 Fault memoryThis command is used to clear the faults stored in the computer.
RZ003 Engine adaptivesThis command enables a long engine start time.
RZ031 Throttle stop programmingThis command is used to reset the necessary system adaptives
if replacing the throttle valve.
RZ033Richness regulation
programmingThis command is used to reset the necessary system adaptives
if replacing the injectors.
RZ037Flywheel target
programmingThis command is used to reset the necessary system adaptives
if replacing the TDC* sensor.
RZ064Programming the level of
alcoholThis command is used to count the richness adaptive
programming necessary when replacing the injection computer.
AC005 Cylinder 1 injectorThis command is used to perform an audible check on injector 1.
AC006 Cylinder 2 injectorThis command is used to perform an audible check on injector 2.
AC007 Cylinder 3 injectorThis command is used to perform an audible check on injector 3.
AC008 Cylinder 4 injectorThis command is used to perform an audible check on injector 4.
AC015 Fuel pump relayThis command is used to check the fuel pump.
AC017Canister bleed solenoid
valveThis command is used to check the canister bleed solenoid
valve.
AC027 Motorised throttleThis command is used to check the motorised throttle.
AC038 Low speed GMV** relayThis command is used to check the low speed GMV** relay.
AC039 High speed GMV** relayThis command is used to check the high speed GMV** relay.
AC180Air conditioning
compressor relay controlThis command is used to check the air conditioning compressor
relay.
PETROL INJECTION
Fault finding – Command summary table

17B-214V2 MR-376-X76-17B050$140.mif
PETROL INJECTION
Fault finding – Command summary table17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AC217Additional fuel circuit
solenoid valveThis command is used to check the additional fuel circuit
solenoid valve. Only on Flexfuel injection
AC224Additional fuel circuit pump
relay This command is used to check the relay of the additional circuit
pump. Only on Flexfuel injection
AC250 Heating resistor 1 relayThis command is used to activate the heating resistor no.1 relay.
AC251 Heating resistor 2 relayThis command is used to activate the heating resistor no.2 relay.
AC252 Heating resistor 3 relayThis command is used to activate the heating resistor no.3 relay.
SC001 Write saved dataUse this command after replacing or (re)programming the
computer (if the data has been saved using command SC003).
SC003 Save computer dataThis command enables the computer operating data, the engine
adaptives, to be recorded.
SC006Start OBD test: Catalytic
converterThis command is used to test the catalytic converter.
SC007 Run OBD test: O2 sensorThis command is used to test the O2 sensors.
SC061Oil change interval (OCS)
OxidationThis command is used to perform a test on the oil oxidation (see
Technical Note 6523A, Oil change interval (OCS) fault finding
for petrol and diesel engines)
VP010 Enter VIN.This command is used to enter the VIN.
VP036 Fuel supply inhibitedThis command is used to inhibit fuel supply to the engine.

17B-215V2 MR-376-X76-17B050$150.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
NOTESSpecial note:
Only address this customer complaint after a complete check with the diagnostic
tool.
NO COMMUNICATION WITH THE COMPUTER ALP1
GENERAL APPEARANCE OF ENGINE COMPARTMENT ALP2
APPEARANCE AND MOUNTING OF THE EXHAUST ALP3
LEAK FROM THE ENGINE
FUEL LEAKALP4
ENGINE OIL LEAKALP5
COOLANT LEAKALP6
ODOURS UNDER BONNET
UNUSUAL ODOURALP7
FUEL ODOURALP8
PETROL INJECTION
Fault finding – Customer complaints

17B-217V2 MR-376-X76-17B050$150.mif
PETROL INJECTION
Fault finding – Customer complaints17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
EXCESSIVE CONSUMPTION
EXCESSIVE FUEL CONSUMPTION ALP 13
EXCESSIVE COOLANT CONSUMPTION ALP14
EXCESSIVE OIL CONSUMPTION ALP15
ENGINE STARTING
IMPOSSIBLE TO START THE ENGINE ALP16
ENGINE STALLS WHEN COLD ALP17
THE ENGINE STARTS WITH DIFFICULTY ALP18
PERFORMANCE
LACK OF POWER OR TORQUE ALP19
ACCELERATION GAP ALP20

17B-219V2 MR-376-X76-17B050$150.mif
PETROL INJECTION
Fault finding – Customer complaints17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
LPG (only for D4F734 and K4M616 engines)
INJECTION WARNING LIGHT: LITTechnical Note 6520
(D4F734 engine on Logan
and Sandero) or Technical
Note 6524 (K4M616 engine
on Duster)
SWITCHING FROM PETROL - CARBURISING GAS: IMPOSSIBLETechnical Note 6520
(D4F734 engine on Logan
and Sandero) or Technical
Note 6524 (K4M616 engine
on Duster)
JERKING WHEN SWITCHING FROM THE FUEL - CARBURISING
GASTechnical Note 6520
(D4F734 engine on Logan
and Sandero) or Technical
Note 6524 (K4M616 engine
on Duster)
FUEL ODOURTechnical Note 6520
(D4F734 engine on Logan
and Sandero) or Technical
Note 6524 (K4M616 engine
on Duster)
CARBURISING MODE CHANGE BUTTON AND WARNING LIGHT:
MALFUNCTIONTechnical Note 6520
(D4F734 engine on Logan
and Sandero) or Technical
Note 6524 (K4M616 engine
on Duster)
CARBURISING MODE CHANGE: UNEXPECTEDTechnical Note 6520
(D4F734 engine on Logan
and Sandero) or Technical
Note 6524 (K4M616 engine
on Duster)